aboutsummaryrefslogtreecommitdiff
path: root/arch/cris/include/asm/etraxgpio.h
blob: d474818a537e75dd3f28164ecf69672050fc5c96 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
/*
 * The following devices are accessable using this driver using
 * GPIO_MAJOR (120) and a couple of minor numbers.
 *
 * For ETRAX 100LX (CONFIG_ETRAX_ARCH_V10):
 * /dev/gpioa  minor 0, 8 bit GPIO, each bit can change direction
 * /dev/gpiob  minor 1, 8 bit GPIO, each bit can change direction
 * /dev/leds   minor 2, Access to leds depending on kernelconfig
 * /dev/gpiog  minor 3
 *       g0dir, g8_15dir, g16_23dir, g24 dir configurable in R_GEN_CONFIG
 *       g1-g7 and g25-g31 is both input and outputs but on different pins
 *       Also note that some bits change pins depending on what interfaces
 *       are enabled.
 *
 * For ETRAX FS (CONFIG_ETRAXFS):
 * /dev/gpioa  minor 0,  8 bit GPIO, each bit can change direction
 * /dev/gpiob  minor 1, 18 bit GPIO, each bit can change direction
 * /dev/gpioc  minor 3, 18 bit GPIO, each bit can change direction
 * /dev/gpiod  minor 4, 18 bit GPIO, each bit can change direction
 * /dev/gpioe  minor 5, 18 bit GPIO, each bit can change direction
 * /dev/leds   minor 2, Access to leds depending on kernelconfig
 *
 * For ARTPEC-3 (CONFIG_CRIS_MACH_ARTPEC3):
 * /dev/gpioa  minor 0, 32 bit GPIO, each bit can change direction
 * /dev/gpiob  minor 1, 32 bit GPIO, each bit can change direction
 * /dev/gpioc  minor 3, 16 bit GPIO, each bit can change direction
 * /dev/gpiod  minor 4, 32 bit GPIO, input only
 * /dev/leds   minor 2, Access to leds depending on kernelconfig
 * /dev/pwm0   minor 16, PWM channel 0 on PA30
 * /dev/pwm1   minor 17, PWM channel 1 on PA31
 * /dev/pwm2   minor 18, PWM channel 2 on PB26
 * /dev/ppwm   minor 19, PPWM channel
 *
 */
#ifndef _ASM_ETRAXGPIO_H
#define _ASM_ETRAXGPIO_H

#define GPIO_MINOR_FIRST 0

#define ETRAXGPIO_IOCTYPE 43

/* etraxgpio _IOC_TYPE, bits 8 to 15 in ioctl cmd */
#ifdef CONFIG_ETRAX_ARCH_V10
#define GPIO_MINOR_A 0
#define GPIO_MINOR_B 1
#define GPIO_MINOR_LEDS 2
#define GPIO_MINOR_G 3
#define GPIO_MINOR_LAST 3
#define GPIO_MINOR_LAST_REAL GPIO_MINOR_LAST
#endif

#ifdef CONFIG_ETRAXFS
#define GPIO_MINOR_A 0
#define GPIO_MINOR_B 1
#define GPIO_MINOR_LEDS 2
#define GPIO_MINOR_C 3
#define GPIO_MINOR_D 4
#define GPIO_MINOR_E 5
#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
#define GPIO_MINOR_V 6
#define GPIO_MINOR_LAST 6
#else
#define GPIO_MINOR_LAST 5
#endif
#define GPIO_MINOR_LAST_REAL GPIO_MINOR_LAST
#endif

#ifdef CONFIG_CRIS_MACH_ARTPEC3
#define GPIO_MINOR_A 0
#define GPIO_MINOR_B 1
#define GPIO_MINOR_LEDS 2
#define GPIO_MINOR_C 3
#define GPIO_MINOR_D 4
#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
#define GPIO_MINOR_V 6
#define GPIO_MINOR_LAST 6
#else
#define GPIO_MINOR_LAST 4
#endif
#define GPIO_MINOR_FIRST_PWM 16
#define GPIO_MINOR_PWM0 (GPIO_MINOR_FIRST_PWM+0)
#define GPIO_MINOR_PWM1 (GPIO_MINOR_FIRST_PWM+1)
#define GPIO_MINOR_PWM2 (GPIO_MINOR_FIRST_PWM+2)
#define GPIO_MINOR_PPWM (GPIO_MINOR_FIRST_PWM+3)
#define GPIO_MINOR_LAST_PWM GPIO_MINOR_PPWM
#define GPIO_MINOR_LAST_REAL GPIO_MINOR_LAST_PWM
#endif



/* supported ioctl _IOC_NR's */

#define IO_READBITS  0x1  /* read and return current port bits (obsolete) */
#define IO_SETBITS   0x2  /* set the bits marked by 1 in the argument */
#define IO_CLRBITS   0x3  /* clear the bits marked by 1 in the argument */

/* the alarm is waited for by select() */

#define IO_HIGHALARM 0x4  /* set alarm on high for bits marked by 1 */
#define IO_LOWALARM  0x5  /* set alarm on low for bits marked by 1 */
#define IO_CLRALARM  0x6  /* clear alarm for bits marked by 1 */

/* LED ioctl */
#define IO_LEDACTIVE_SET 0x7 /* set active led
                              * 0=off, 1=green, 2=red, 3=yellow */

/* GPIO direction ioctl's */
#define IO_READDIR    0x8  /* Read direction 0=input 1=output  (obsolete) */
#define IO_SETINPUT   0x9  /* Set direction for bits set, 0=unchanged 1=input,
                              returns mask with current inputs (obsolete) */
#define IO_SETOUTPUT  0xA  /* Set direction for bits set, 0=unchanged 1=output,
                              returns mask with current outputs (obsolete)*/

/* LED ioctl extended */
#define IO_LED_SETBIT 0xB
#define IO_LED_CLRBIT 0xC

/* SHUTDOWN ioctl */
#define IO_SHUTDOWN   0xD
#define IO_GET_PWR_BT 0xE

/* Bit toggling in driver settings */
/* bit set in low byte0 is CLK mask (0x00FF),
   bit set in byte1 is DATA mask    (0xFF00)
   msb, data_mask[7:0] , clk_mask[7:0]
 */
#define IO_CFG_WRITE_MODE 0xF
#define IO_CFG_WRITE_MODE_VALUE(msb, data_mask, clk_mask) \
	( (((msb)&1) << 16) | (((data_mask) &0xFF) << 8) | ((clk_mask) & 0xFF) )

/* The following 4 ioctl's take a pointer as argument and handles
 * 32 bit ports (port G) properly.
 * These replaces IO_READBITS,IO_SETINPUT AND IO_SETOUTPUT
 */
#define IO_READ_INBITS   0x10 /* *arg is result of reading the input pins */
#define IO_READ_OUTBITS  0x11 /* *arg is result of reading the output shadow */
#define IO_SETGET_INPUT  0x12 /* bits set in *arg is set to input, */
			      /* *arg updated with current input pins. */
#define IO_SETGET_OUTPUT 0x13 /* bits set in *arg is set to output, */
			      /* *arg updated with current output pins. */

/* The following ioctl's are applicable to the PWM channels only */

#define IO_PWM_SET_MODE     0x20

enum io_pwm_mode {
	PWM_OFF = 0,		/* disabled, deallocated */
	PWM_STANDARD = 1,	/* 390 kHz, duty cycle 0..255/256 */
	PWM_FAST = 2,		/* variable freq, w/ 10ns active pulse len */
	PWM_VARFREQ = 3,	/* individually configurable high/low periods */
	PWM_SOFT = 4		/* software generated */
};

struct io_pwm_set_mode {
	enum io_pwm_mode mode;
};

/* Only for mode PWM_VARFREQ. Period lo/high set in increments of 10ns
 * from 10ns (value = 0) to 81920ns (value = 8191)
 * (Resulting frequencies range from 50 MHz (10ns + 10ns) down to
 * 6.1 kHz (81920ns + 81920ns) at 50% duty cycle, to 12.2 kHz at min/max duty
 * cycle (81920 + 10ns or 10ns + 81920ns, respectively).)
 */
#define IO_PWM_SET_PERIOD   0x21

struct io_pwm_set_period {
	unsigned int lo;		/* 0..8191 */
	unsigned int hi;		/* 0..8191 */
};

/* Only for modes PWM_STANDARD and PWM_FAST.
 * For PWM_STANDARD, set duty cycle of 390 kHz PWM output signal, from
 * 0 (value = 0) to 255/256 (value = 255).
 * For PWM_FAST, set duty cycle of PWM output signal from
 * 0% (value = 0) to 100% (value = 255). Output signal in this mode
 * is a 10ns pulse surrounded by a high or low level depending on duty
 * cycle (except for 0% and 100% which result in a constant output).
 * Resulting output frequency varies from 50 MHz at 50% duty cycle,
 * down to 390 kHz at min/max duty cycle.
 */
#define IO_PWM_SET_DUTY     0x22

struct io_pwm_set_duty {
	int duty;		/* 0..255 */
};

/* Returns information about the latest PWM pulse.
 * lo: Length of the latest low period, in units of 10ns.
 * hi: Length of the latest high period, in units of 10ns.
 * cnt: Time since last detected edge, in units of 10ns.
 *
 * The input source to PWM is decied by IO_PWM_SET_INPUT_SRC.
 *
 * NOTE: All PWM devices is connected to the same input source.
 */
#define IO_PWM_GET_PERIOD   0x23

struct io_pwm_get_period {
	unsigned int lo;
	unsigned int hi;
	unsigned int cnt;
};

/* Sets the input source for the PWM input. For the src value see the
 * register description for gio:rw_pwm_in_cfg.
 *
 * NOTE: All PWM devices is connected to the same input source.
 */
#define IO_PWM_SET_INPUT_SRC   0x24
struct io_pwm_set_input_src {
	unsigned int src;	/* 0..7 */
};

/* Sets the duty cycles in steps of 1/256, 0 = 0%, 255 = 100% duty cycle */
#define IO_PPWM_SET_DUTY     0x25

struct io_ppwm_set_duty {
	int duty;		/* 0..255 */
};

/* Configuraton struct for the IO_PWMCLK_SET_CONFIG ioctl to configure
 * PWM capable gpio pins:
 */
#define IO_PWMCLK_SETGET_CONFIG 0x26
struct gpio_pwmclk_conf {
  unsigned int gpiopin; /* The pin number based on the opened device */
  unsigned int baseclk; /* The base clock to use, or sw will select one close*/
  unsigned int low;     /* The number of low periods of the baseclk */
  unsigned int high;    /* The number of high periods of the baseclk */
};

/* Examples:
 * To get a symmetric 12 MHz clock without knowing anything about the hardware:
 * baseclk = 12000000, low = 0, high = 0
 * To just get info of current setting:
 * baseclk = 0, low = 0, high = 0, the values will be updated by driver.
 */

#endif