aboutsummaryrefslogtreecommitdiff
path: root/arch/x86/kernel/reboot_32.S
blob: 1d5c46df0d787abc497a1d025a9a8fd2cd347026 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
#include <linux/linkage.h>
#include <linux/init.h>
#include <asm/segment.h>
#include <asm/page_types.h>

/*
 * The following code and data reboots the machine by switching to real
 * mode and jumping to the BIOS reset entry point, as if the CPU has
 * really been reset.  The previous version asked the keyboard
 * controller to pulse the CPU reset line, which is more thorough, but
 * doesn't work with at least one type of 486 motherboard.  It is easy
 * to stop this code working; hence the copious comments.
 *
 * This code is called with the restart type (0 = BIOS, 1 = APM) in %eax.
 */
	.section ".x86_trampoline","a"
	.balign 16
	.code32
ENTRY(machine_real_restart_asm)
r_base = .
	/* Get our own relocated address */
	call	1f
1:	popl	%ebx
	subl	$(1b - r_base), %ebx

	/* Compute the equivalent real-mode segment */
	movl	%ebx, %ecx
	shrl	$4, %ecx
	
	/* Patch post-real-mode segment jump */
	movw	(dispatch_table - r_base)(%ebx,%eax,2),%ax
	movw	%ax, (101f - r_base)(%ebx)
	movw	%cx, (102f - r_base)(%ebx)

	/* Set up the IDT for real mode. */
	lidtl	(machine_real_restart_idt - r_base)(%ebx)

	/*
	 * Set up a GDT from which we can load segment descriptors for real
	 * mode.  The GDT is not used in real mode; it is just needed here to
	 * prepare the descriptors.
	 */
	lgdtl	(machine_real_restart_gdt - r_base)(%ebx)

	/*
	 * Load the data segment registers with 16-bit compatible values
	 */
	movl	$16, %ecx
	movl	%ecx, %ds
	movl	%ecx, %es
	movl	%ecx, %fs
	movl	%ecx, %gs
	movl	%ecx, %ss
	ljmpl	$8, $1f - r_base

/*
 * This is 16-bit protected mode code to disable paging and the cache,
 * switch to real mode and jump to the BIOS reset code.
 *
 * The instruction that switches to real mode by writing to CR0 must be
 * followed immediately by a far jump instruction, which set CS to a
 * valid value for real mode, and flushes the prefetch queue to avoid
 * running instructions that have already been decoded in protected
 * mode.
 *
 * Clears all the flags except ET, especially PG (paging), PE
 * (protected-mode enable) and TS (task switch for coprocessor state
 * save).  Flushes the TLB after paging has been disabled.  Sets CD and
 * NW, to disable the cache on a 486, and invalidates the cache.  This
 * is more like the state of a 486 after reset.  I don't know if
 * something else should be done for other chips.
 *
 * More could be done here to set up the registers as if a CPU reset had
 * occurred; hopefully real BIOSs don't assume much.  This is not the
 * actual BIOS entry point, anyway (that is at 0xfffffff0).
 *
 * Most of this work is probably excessive, but it is what is tested.
 */
	.code16
1:
	xorl	%ecx, %ecx
	movl	%cr0, %eax
	andl	$0x00000011, %eax
	orl	$0x60000000, %eax
	movl	%eax, %cr0
	movl	%ecx, %cr3
	movl	%cr0, %edx
	andl	$0x60000000, %edx	/* If no cache bits -> no wbinvd */
	jz	2f
	wbinvd
2:
	andb	$0x10, %al
	movl	%eax, %cr0
	.byte	0xea			/* ljmpw */
101:	.word	0			/* Offset */
102:	.word	0			/* Segment */

bios:
	ljmpw	$0xf000, $0xfff0

apm:
	movw	$0x1000, %ax
	movw	%ax, %ss
	movw	$0xf000, %sp
	movw	$0x5307, %ax
	movw	$0x0001, %bx
	movw	$0x0003, %cx
	int	$0x15

END(machine_real_restart_asm)

	.balign 16
	/* These must match <asm/reboot.h */
dispatch_table:
	.word	bios - r_base
	.word	apm - r_base
END(dispatch_table)

	.balign 16
machine_real_restart_idt:
	.word	0xffff		/* Length - real mode default value */
	.long	0		/* Base - real mode default value */
END(machine_real_restart_idt)

	.balign 16
ENTRY(machine_real_restart_gdt)
	.quad	0		/* Self-pointer, filled in by PM code */
	.quad	0		/* 16-bit code segment, filled in by PM code */
	/*
	 * 16-bit data segment with the selector value 16 = 0x10 and
	 * base value 0x100; since this is consistent with real mode
	 * semantics we don't have to reload the segments once CR0.PE = 0.
	 */
	.quad	GDT_ENTRY(0x0093, 0x100, 0xffff)
END(machine_real_restart_gdt)