aboutsummaryrefslogtreecommitdiff
path: root/include/uapi/linux/fdreg.h
blob: 61ce64169004a84ba753321a8d7a988d3b768259 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
#ifndef _LINUX_FDREG_H
#define _LINUX_FDREG_H
/*
 * This file contains some defines for the floppy disk controller.
 * Various sources. Mostly "IBM Microcomputers: A Programmers
 * Handbook", Sanches and Canton.
 */

#ifdef FDPATCHES
#define FD_IOPORT fdc_state[fdc].address
#else
/* It would be a lot saner just to force fdc_state[fdc].address to always
   be set ! FIXME */
#define FD_IOPORT 0x3f0
#endif

/* Fd controller regs. S&C, about page 340 */
#define FD_STATUS	(4 + FD_IOPORT )
#define FD_DATA		(5 + FD_IOPORT )

/* Digital Output Register */
#define FD_DOR		(2 + FD_IOPORT )

/* Digital Input Register (read) */
#define FD_DIR		(7 + FD_IOPORT )

/* Diskette Control Register (write)*/
#define FD_DCR		(7 + FD_IOPORT )

/* Bits of main status register */
#define STATUS_BUSYMASK	0x0F		/* drive busy mask */
#define STATUS_BUSY	0x10		/* FDC busy */
#define STATUS_DMA	0x20		/* 0- DMA mode */
#define STATUS_DIR	0x40		/* 0- cpu->fdc */
#define STATUS_READY	0x80		/* Data reg ready */

/* Bits of FD_ST0 */
#define ST0_DS		0x03		/* drive select mask */
#define ST0_HA		0x04		/* Head (Address) */
#define ST0_NR		0x08		/* Not Ready */
#define ST0_ECE		0x10		/* Equipment check error */
#define ST0_SE		0x20		/* Seek end */
#define ST0_INTR	0xC0		/* Interrupt code mask */

/* Bits of FD_ST1 */
#define ST1_MAM		0x01		/* Missing Address Mark */
#define ST1_WP		0x02		/* Write Protect */
#define ST1_ND		0x04		/* No Data - unreadable */
#define ST1_OR		0x10		/* OverRun */
#define ST1_CRC		0x20		/* CRC error in data or addr */
#define ST1_EOC		0x80		/* End Of Cylinder */

/* Bits of FD_ST2 */
#define ST2_MAM		0x01		/* Missing Address Mark (again) */
#define ST2_BC		0x02		/* Bad Cylinder */
#define ST2_SNS		0x04		/* Scan Not Satisfied */
#define ST2_SEH		0x08		/* Scan Equal Hit */
#define ST2_WC		0x10		/* Wrong Cylinder */
#define ST2_CRC		0x20		/* CRC error in data field */
#define ST2_CM		0x40		/* Control Mark = deleted */

/* Bits of FD_ST3 */
#define ST3_HA		0x04		/* Head (Address) */
#define ST3_DS		0x08		/* drive is double-sided */
#define ST3_TZ		0x10		/* Track Zero signal (1=track 0) */
#define ST3_RY		0x20		/* drive is ready */
#define ST3_WP		0x40		/* Write Protect */
#define ST3_FT		0x80		/* Drive Fault */

/* Values for FD_COMMAND */
#define FD_RECALIBRATE		0x07	/* move to track 0 */
#define FD_SEEK			0x0F	/* seek track */
#define FD_READ			0xE6	/* read with MT, MFM, SKip deleted */
#define FD_WRITE		0xC5	/* write with MT, MFM */
#define FD_SENSEI		0x08	/* Sense Interrupt Status */
#define FD_SPECIFY		0x03	/* specify HUT etc */
#define FD_FORMAT		0x4D	/* format one track */
#define FD_VERSION		0x10	/* get version code */
#define FD_CONFIGURE		0x13	/* configure FIFO operation */
#define FD_PERPENDICULAR	0x12	/* perpendicular r/w mode */
#define FD_GETSTATUS		0x04	/* read ST3 */
#define FD_DUMPREGS		0x0E	/* dump the contents of the fdc regs */
#define FD_READID		0xEA	/* prints the header of a sector */
#define FD_UNLOCK		0x14	/* Fifo config unlock */
#define FD_LOCK			0x94	/* Fifo config lock */
#define FD_RSEEK_OUT		0x8f	/* seek out (i.e. to lower tracks) */
#define FD_RSEEK_IN		0xcf	/* seek in (i.e. to higher tracks) */

/* the following commands are new in the 82078. They are not used in the
 * floppy driver, except the first three. These commands may be useful for apps
 * which use the FDRAWCMD interface. For doc, get the 82078 spec sheets at
 * http://www.intel.com/design/archives/periphrl/docs/29046803.htm */

#define FD_PARTID		0x18	/* part id ("extended" version cmd) */
#define FD_SAVE			0x2e	/* save fdc regs for later restore */
#define FD_DRIVESPEC		0x8e	/* drive specification: Access to the
					 * 2 Mbps data transfer rate for tape
					 * drives */

#define FD_RESTORE		0x4e    /* later restore */
#define FD_POWERDOWN		0x27	/* configure FDC's powersave features */
#define FD_FORMAT_N_WRITE	0xef    /* format and write in one go. */
#define FD_OPTION		0x33	/* ISO format (which is a clean way to
					 * pack more sectors on a track) */

/* DMA commands */
#define DMA_READ	0x46
#define DMA_WRITE	0x4A

/* FDC version return types */
#define FDC_NONE	0x00
#define FDC_UNKNOWN	0x10	/* DO NOT USE THIS TYPE EXCEPT IF IDENTIFICATION
				   FAILS EARLY */
#define FDC_8272A	0x20	/* Intel 8272a, NEC 765 */
#define FDC_765ED	0x30	/* Non-Intel 1MB-compatible FDC, can't detect */
#define FDC_82072	0x40	/* Intel 82072; 8272a + FIFO + DUMPREGS */
#define FDC_82072A	0x45	/* 82072A (on Sparcs) */
#define FDC_82077_ORIG	0x51	/* Original version of 82077AA, sans LOCK */
#define FDC_82077	0x52	/* 82077AA-1 */
#define FDC_82078_UNKN	0x5f	/* Unknown 82078 variant */
#define FDC_82078	0x60	/* 44pin 82078 or 64pin 82078SL */
#define FDC_82078_1	0x61	/* 82078-1 (2Mbps fdc) */
#define FDC_S82078B	0x62	/* S82078B (first seen on Adaptec AVA-2825 VLB
				 * SCSI/EIDE/Floppy controller) */
#define FDC_87306	0x63	/* National Semiconductor PC 87306 */

/*
 * Beware: the fdc type list is roughly sorted by increasing features.
 * Presence of features is tested by comparing the FDC version id with the
 * "oldest" version that has the needed feature.
 * If during FDC detection, an obscure test fails late in the sequence, don't
 * assign FDC_UNKNOWN. Else the FDC will be treated as a dumb 8272a, or worse.
 * This is especially true if the tests are unneeded.
 */

#define FD_RESET_DELAY 20
#endif