Merge remote-tracking branch 'l2-mtd/master'

3 files changed, 152 insertions, 5 deletions

diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
index 3e7ee99d3949..f6bee57e453a 100644
--- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
@@ -1,4 +1,109 @@
-Atmel NAND flash
+Atmel NAND flash controller bindings
+
+The NAND flash controller node should be defined under the EBI bus (see
+Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt).
+One or several NAND devices can be defined under this NAND controller.
+The NAND controller might be connected to an ECC engine.
+
+* NAND controller bindings:
+
+Required properties:
+- compatible: should be one of the following
+	"atmel,at91rm9200-nand-controller"
+	"atmel,at91sam9260-nand-controller"
+	"atmel,at91sam9261-nand-controller"
+	"atmel,at91sam9g45-nand-controller"
+	"atmel,sama5d3-nand-controller"
+- ranges: empty ranges property to forward EBI ranges definitions.
+- #address-cells: should be set to 2.
+- #size-cells: should be set to 1.
+- atmel,nfc-io: phandle to the NFC IO block. Only required for sama5d3
+		controllers.
+- atmel,nfc-sram: phandle to the NFC SRAM block. Only required for sama5d3
+		  controllers.
+
+Optional properties:
+- ecc-engine: phandle to the PMECC block. Only meaningful if the SoC embeds
+	      a PMECC engine.
+
+* NAND device/chip bindings:
+
+Required properties:
+- reg: describes the CS lines assigned to the NAND device. If the NAND device
+       exposes multiple CS lines (multi-dies chips), your reg property will
+       contain X tuples of 3 entries.
+       1st entry: the CS line this NAND chip is connected to
+       2nd entry: the base offset of the memory region assigned to this
+		  device (always 0)
+       3rd entry: the memory region size (always 0x800000)
+
+Optional properties:
+- rb-gpios: the GPIO(s) used to check the Ready/Busy status of the NAND.
+- cs-gpios: the GPIO(s) used to control the CS line.
+- det-gpios: the GPIO used to detect if a Smartmedia Card is present.
+- atmel,rb: an integer identifying the native Ready/Busy pin. Only meaningful
+	    on sama5 SoCs.
+
+All generic properties described in
+Documentation/devicetree/bindings/mtd/{common,nand}.txt also apply to the NAND
+device node, and NAND partitions should be defined under the NAND node as
+described in Documentation/devicetree/bindings/mtd/partition.txt.
+
+* ECC engine (PMECC) bindings:
+
+Required properties:
+- compatible: should be one of the following
+	"atmel,at91sam9g45-pmecc"
+	"atmel,sama5d4-pmecc"
+	"atmel,sama5d2-pmecc"
+- reg: should contain 2 register ranges. The first one is pointing to the PMECC
+       block, and the second one to the PMECC_ERRLOC block.
+
+Example:
+
+	pmecc: ecc-engine@ffffc070 {
+		compatible = "atmel,at91sam9g45-pmecc";
+                reg = <0xffffc070 0x490>,
+                      <0xffffc500 0x100>;
+	};
+
+	ebi: ebi@10000000 {
+		compatible = "atmel,sama5d3-ebi";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		atmel,smc = <&hsmc>;
+		reg = <0x10000000 0x10000000
+		       0x40000000 0x30000000>;
+		ranges = <0x0 0x0 0x10000000 0x10000000
+			  0x1 0x0 0x40000000 0x10000000
+			  0x2 0x0 0x50000000 0x10000000
+			  0x3 0x0 0x60000000 0x10000000>;
+		clocks = <&mck>;
+
+                nand_controller: nand-controller {
+			compatible = "atmel,sama5d3-nand-controller";
+			atmel,nfc-sram = <&nfc_sram>;
+			atmel,nfc-io = <&nfc_io>;
+			ecc-engine = <&pmecc>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			ranges;
+
+			nand@3 {
+				reg = <0x3 0x0 0x800000>;
+				atmel,rb = <0>;
+
+				/*
+				 * Put generic NAND/MTD properties and
+				 * subnodes here.
+				 */
+			};
+		};
+	};
+
+-----------------------------------------------------------------------
+
+Deprecated bindings (should not be used in new device trees):
 
 Required properties:
 - compatible: The possible values are:
diff --git a/Documentation/devicetree/bindings/mtd/denali-nand.txt b/Documentation/devicetree/bindings/mtd/denali-nand.txt
index b04d03a1d499..e593bbeb2115 100644
--- a/Documentation/devicetree/bindings/mtd/denali-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/denali-nand.txt
@@ -1,11 +1,11 @@
 * Denali NAND controller
 
 Required properties:
-  - compatible : should be "denali,denali-nand-dt"
+  - compatible : should be one of the following:
+      "altr,socfpga-denali-nand"            - for Altera SOCFPGA
   - reg : should contain registers location and length for data and reg.
   - reg-names: Should contain the reg names "nand_data" and "denali_reg"
   - interrupts : The interrupt number.
-  - dm-mask : DMA bit mask
 
 The device tree may optionally contain sub-nodes describing partitions of the
 address space. See partition.txt for more detail.
@@ -15,9 +15,8 @@ Examples:
 nand: nand@ff900000 {
 	#address-cells = <1>;
 	#size-cells = <1>;
-	compatible = "denali,denali-nand-dt";
+	compatible = "altr,socfpga-denali-nand";
 	reg = <0xff900000 0x100000>, <0xffb80000 0x10000>;
 	reg-names = "nand_data", "denali_reg";
 	interrupts = <0 144 4>;
-	dma-mask = <0xffffffff>;
 };
diff --git a/Documentation/devicetree/bindings/mtd/stm32-quadspi.txt b/Documentation/devicetree/bindings/mtd/stm32-quadspi.txt
new file mode 100644
index 000000000000..ddd18c135148
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/stm32-quadspi.txt
@@ -0,0 +1,43 @@
+* STMicroelectronics Quad Serial Peripheral Interface(QuadSPI)
+
+Required properties:
+- compatible: should be "st,stm32f469-qspi"
+- reg: the first contains the register location and length.
+       the second contains the memory mapping address and length
+- reg-names: should contain the reg names "qspi" "qspi_mm"
+- interrupts: should contain the interrupt for the device
+- clocks: the phandle of the clock needed by the QSPI controller
+- A pinctrl must be defined to set pins in mode of operation for QSPI transfer
+
+Optional properties:
+- resets: must contain the phandle to the reset controller.
+
+A spi flash must be a child of the nor_flash node and could have some
+properties. Also see jedec,spi-nor.txt.
+
+Required properties:
+- reg: chip-Select number (QSPI controller may connect 2 nor flashes)
+- spi-max-frequency: max frequency of spi bus
+
+Optional property:
+- spi-rx-bus-width: see ../spi/spi-bus.txt for the description
+
+Example:
+
+qspi: spi@a0001000 {
+	compatible = "st,stm32f469-qspi";
+	reg = <0xa0001000 0x1000>, <0x90000000 0x10000000>;
+	reg-names = "qspi", "qspi_mm";
+	interrupts = <91>;
+	resets = <&rcc STM32F4_AHB3_RESET(QSPI)>;
+	clocks = <&rcc 0 STM32F4_AHB3_CLOCK(QSPI)>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi0>;
+
+	flash@0 {
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		...
+	};
+};