diff options
Diffstat (limited to 'Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt | 108 |
1 files changed, 108 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt new file mode 100644 index 000000000000..8310073f14e1 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt @@ -0,0 +1,108 @@ +STMicroelectronics STM32 ADC device driver + +STM32 ADC is a successive approximation analog-to-digital converter. +It has several multiplexed input channels. Conversions can be performed +in single, continuous, scan or discontinuous mode. Result of the ADC is +stored in a left-aligned or right-aligned 32-bit data register. +Conversions can be launched in software or using hardware triggers. + +The analog watchdog feature allows the application to detect if the input +voltage goes beyond the user-defined, higher or lower thresholds. + +Each STM32 ADC block can have up to 3 ADC instances. + +Each instance supports two contexts to manage conversions, each one has its +own configurable sequence and trigger: +- regular conversion can be done in sequence, running in background +- injected conversions have higher priority, and so have the ability to + interrupt regular conversion sequence (either triggered in SW or HW). + Regular sequence is resumed, in case it has been interrupted. + +Contents of a stm32 adc root node: +----------------------------------- +Required properties: +- compatible: Should be one of: + "st,stm32f4-adc-core" + "st,stm32h7-adc-core" +- reg: Offset and length of the ADC block register set. +- interrupts: Must contain the interrupt for ADC block. +- clocks: Core can use up to two clocks, depending on part used: + - "adc" clock: for the analog circuitry, common to all ADCs. + It's required on stm32f4. + It's optional on stm32h7. + - "bus" clock: for registers access, common to all ADCs. + It's not present on stm32f4. + It's required on stm32h7. +- clock-names: Must be "adc" and/or "bus" depending on part used. +- interrupt-controller: Identifies the controller node as interrupt-parent +- vref-supply: Phandle to the vref input analog reference voltage. +- #interrupt-cells = <1>; +- #address-cells = <1>; +- #size-cells = <0>; + +Optional properties: +- A pinctrl state named "default" for each ADC channel may be defined to set + inX ADC pins in mode of operation for analog input on external pin. + +Contents of a stm32 adc child node: +----------------------------------- +An ADC block node should contain at least one subnode, representing an +ADC instance available on the machine. + +Required properties: +- compatible: Should be one of: + "st,stm32f4-adc" + "st,stm32h7-adc" +- reg: Offset of ADC instance in ADC block (e.g. may be 0x0, 0x100, 0x200). +- clocks: Input clock private to this ADC instance. It's required only on + stm32f4, that has per instance clock input for registers access. +- interrupt-parent: Phandle to the parent interrupt controller. +- interrupts: IRQ Line for the ADC (e.g. may be 0 for adc@0, 1 for adc@100 or + 2 for adc@200). +- st,adc-channels: List of single-ended channels muxed for this ADC. + It can have up to 16 channels on stm32f4 or 20 channels on stm32h7, numbered + from 0 to 15 or 19 (resp. for in0..in15 or in0..in19). +- #io-channel-cells = <1>: See the IIO bindings section "IIO consumers" in + Documentation/devicetree/bindings/iio/iio-bindings.txt + +Optional properties: +- dmas: Phandle to dma channel for this ADC instance. + See ../../dma/dma.txt for details. +- dma-names: Must be "rx" when dmas property is being used. +- assigned-resolution-bits: Resolution (bits) to use for conversions. Must + match device available resolutions: + * can be 6, 8, 10 or 12 on stm32f4 + * can be 8, 10, 12, 14 or 16 on stm32h7 + Default is maximum resolution if unset. + +Example: + adc: adc@40012000 { + compatible = "st,stm32f4-adc-core"; + reg = <0x40012000 0x400>; + interrupts = <18>; + clocks = <&rcc 0 168>; + clock-names = "adc"; + vref-supply = <®_vref>; + interrupt-controller; + pinctrl-names = "default"; + pinctrl-0 = <&adc3_in8_pin>; + + #interrupt-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + compatible = "st,stm32f4-adc"; + #io-channel-cells = <1>; + reg = <0x0>; + clocks = <&rcc 0 168>; + interrupt-parent = <&adc>; + interrupts = <0>; + st,adc-channels = <8>; + dmas = <&dma2 0 0 0x400 0x0>; + dma-names = "rx"; + assigned-resolution-bits = <8>; + }; + ... + other adc child nodes follow... + }; |