diff options
Diffstat (limited to 'Documentation/devicetree/bindings/media')
50 files changed, 1996 insertions, 108 deletions
diff --git a/Documentation/devicetree/bindings/media/atmel-isc.txt b/Documentation/devicetree/bindings/media/atmel-isc.txt new file mode 100644 index 000000000000..bbe0e87c6188 --- /dev/null +++ b/Documentation/devicetree/bindings/media/atmel-isc.txt @@ -0,0 +1,65 @@ +Atmel Image Sensor Controller (ISC) +---------------------------------------------- + +Required properties for ISC: +- compatible + Must be "atmel,sama5d2-isc". +- reg + Physical base address and length of the registers set for the device. +- interrupts + Should contain IRQ line for the ISC. +- clocks + List of clock specifiers, corresponding to entries in + the clock-names property; + Please refer to clock-bindings.txt. +- clock-names + Required elements: "hclock", "iscck", "gck". +- #clock-cells + Should be 0. +- clock-output-names + Should be "isc-mck". +- pinctrl-names, pinctrl-0 + Please refer to pinctrl-bindings.txt. + +ISC supports a single port node with parallel bus. It should contain one +'port' child node with child 'endpoint' node. Please refer to the bindings +defined in Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: +isc: isc@f0008000 { + compatible = "atmel,sama5d2-isc"; + reg = <0xf0008000 0x4000>; + interrupts = <46 IRQ_TYPE_LEVEL_HIGH 5>; + clocks = <&isc_clk>, <&iscck>, <&isc_gclk>; + clock-names = "hclock", "iscck", "gck"; + #clock-cells = <0>; + clock-output-names = "isc-mck"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_isc_base &pinctrl_isc_data_8bit &pinctrl_isc_data_9_10 &pinctrl_isc_data_11_12>; + + port { + isc_0: endpoint { + remote-endpoint = <&ov7740_0>; + hsync-active = <1>; + vsync-active = <0>; + pclk-sample = <1>; + }; + }; +}; + +i2c1: i2c@fc028000 { + ov7740: camera@21 { + compatible = "ovti,ov7740"; + reg = <0x21>; + clocks = <&isc>; + clock-names = "xvclk"; + assigned-clocks = <&isc>; + assigned-clock-rates = <24000000>; + + port { + ov7740_0: endpoint { + remote-endpoint = <&isc_0>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/atmel-isi.txt b/Documentation/devicetree/bindings/media/atmel-isi.txt index 251f008f220c..332513a151cc 100644 --- a/Documentation/devicetree/bindings/media/atmel-isi.txt +++ b/Documentation/devicetree/bindings/media/atmel-isi.txt @@ -1,51 +1,66 @@ -Atmel Image Sensor Interface (ISI) SoC Camera Subsystem ----------------------------------------------- - -Required properties: -- compatible: must be "atmel,at91sam9g45-isi" -- reg: physical base address and length of the registers set for the device; -- interrupts: should contain IRQ line for the ISI; -- clocks: list of clock specifiers, corresponding to entries in - the clock-names property; -- clock-names: must contain "isi_clk", which is the isi peripherial clock. - -ISI supports a single port node with parallel bus. It should contain one +Atmel Image Sensor Interface (ISI) +---------------------------------- + +Required properties for ISI: +- compatible: must be "atmel,at91sam9g45-isi". +- reg: physical base address and length of the registers set for the device. +- interrupts: should contain IRQ line for the ISI. +- clocks: list of clock specifiers, corresponding to entries in the clock-names + property; please refer to clock-bindings.txt. +- clock-names: required elements: "isi_clk". +- pinctrl-names, pinctrl-0: please refer to pinctrl-bindings.txt. + +ISI supports a single port node with parallel bus. It shall contain one 'port' child node with child 'endpoint' node. Please refer to the bindings defined in Documentation/devicetree/bindings/media/video-interfaces.txt. -Example: - isi: isi@f0034000 { - compatible = "atmel,at91sam9g45-isi"; - reg = <0xf0034000 0x4000>; - interrupts = <37 IRQ_TYPE_LEVEL_HIGH 5>; - - clocks = <&isi_clk>; - clock-names = "isi_clk"; +Endpoint node properties +------------------------ - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_isi>; +- bus-width: <8> or <10> (mandatory) +- hsync-active (default: active high) +- vsync-active (default: active high) +- pclk-sample (default: sample on falling edge) +- remote-endpoint: A phandle to the bus receiver's endpoint node (mandatory). - port { - #address-cells = <1>; - #size-cells = <0>; +Example: - isi_0: endpoint { - remote-endpoint = <&ov2640_0>; - bus-width = <8>; - }; +isi: isi@f0034000 { + compatible = "atmel,at91sam9g45-isi"; + reg = <0xf0034000 0x4000>; + interrupts = <37 IRQ_TYPE_LEVEL_HIGH 5>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_isi_data_0_7>; + clocks = <&isi_clk>; + clock-names = "isi_clk"; + port { + isi_0: endpoint { + remote-endpoint = <&ov2640_0>; + bus-width = <8>; + vsync-active = <1>; + hsync-active = <1>; }; }; +}; - i2c1: i2c@f0018000 { - ov2640: camera@0x30 { - compatible = "ovti,ov2640"; - reg = <0x30>; +i2c1: i2c@f0018000 { + ov2640: camera@30 { + compatible = "ovti,ov2640"; + reg = <0x30>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>; + resetb-gpios = <&pioE 11 GPIO_ACTIVE_LOW>; + pwdn-gpios = <&pioE 13 GPIO_ACTIVE_HIGH>; + clocks = <&pck0>; + clock-names = "xvclk"; + assigned-clocks = <&pck0>; + assigned-clock-rates = <25000000>; - port { - ov2640_0: endpoint { - remote-endpoint = <&isi_0>; - bus-width = <8>; - }; + port { + ov2640_0: endpoint { + remote-endpoint = <&isi_0>; + bus-width = <8>; }; }; }; +}; diff --git a/Documentation/devicetree/bindings/media/cec.txt b/Documentation/devicetree/bindings/media/cec.txt new file mode 100644 index 000000000000..22d7aae3d3d7 --- /dev/null +++ b/Documentation/devicetree/bindings/media/cec.txt @@ -0,0 +1,8 @@ +Common bindings for HDMI CEC adapters + +- hdmi-phandle: phandle to the HDMI controller. + +- needs-hpd: if present the CEC support is only available when the HPD + is high. Some boards only let the CEC pin through if the HPD is high, + for example if there is a level converter that uses the HPD to power + up or down. diff --git a/Documentation/devicetree/bindings/media/exynos4-fimc-is.txt b/Documentation/devicetree/bindings/media/exynos4-fimc-is.txt index 55c9ad6f9599..32ced99d4244 100644 --- a/Documentation/devicetree/bindings/media/exynos4-fimc-is.txt +++ b/Documentation/devicetree/bindings/media/exynos4-fimc-is.txt @@ -16,9 +16,10 @@ Required properties: - clocks : list of clock specifiers, corresponding to entries in clock-names property; - clock-names : must contain "ppmuispx", "ppmuispx", "lite0", "lite1" - "mpll", "sysreg", "isp", "drc", "fd", "mcuisp", "uart", - "ispdiv0", "ispdiv1", "mcuispdiv0", "mcuispdiv1", "aclk200", - "div_aclk200", "aclk400mcuisp", "div_aclk400mcuisp" entries, + "mpll", "sysreg", "isp", "drc", "fd", "mcuisp", "gicisp", + "pwm_isp", "mcuctl_isp", "uart", "ispdiv0", "ispdiv1", + "mcuispdiv0", "mcuispdiv1", "aclk200", "div_aclk200", + "aclk400mcuisp", "div_aclk400mcuisp" entries, matching entries in the clocks property. pmu subnode ----------- diff --git a/Documentation/devicetree/bindings/media/exynos5-gsc.txt b/Documentation/devicetree/bindings/media/exynos5-gsc.txt index 5fe9372abb37..26ca25b6d264 100644 --- a/Documentation/devicetree/bindings/media/exynos5-gsc.txt +++ b/Documentation/devicetree/bindings/media/exynos5-gsc.txt @@ -3,7 +3,8 @@ G-Scaler is used for scaling and color space conversion on EXYNOS5 SoCs. Required properties: -- compatible: should be "samsung,exynos5-gsc" +- compatible: should be "samsung,exynos5-gsc" (for Exynos 5250, 5420 and + 5422 SoCs) or "samsung,exynos5433-gsc" (Exynos 5433) - reg: should contain G-Scaler physical address location and length. - interrupts: should contain G-Scaler interrupt number diff --git a/Documentation/devicetree/bindings/media/fsl-vdoa.txt b/Documentation/devicetree/bindings/media/fsl-vdoa.txt new file mode 100644 index 000000000000..6c5628530bb7 --- /dev/null +++ b/Documentation/devicetree/bindings/media/fsl-vdoa.txt @@ -0,0 +1,21 @@ +Freescale Video Data Order Adapter +================================== + +The Video Data Order Adapter (VDOA) is present on the i.MX6q. Its sole purpose +is to reorder video data from the macroblock tiled order produced by the CODA +960 VPU to the conventional raster-scan order for scanout. + +Required properties: +- compatible: must be "fsl,imx6q-vdoa" +- reg: the register base and size for the device registers +- interrupts: the VDOA interrupt +- clocks: the vdoa clock + +Example: + +vdoa@21e4000 { + compatible = "fsl,imx6q-vdoa"; + reg = <0x021e4000 0x4000>; + interrupts = <0 18 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6QDL_CLK_VDOA>; +}; diff --git a/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt b/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt index 56e726ef4bf2..58261fb7b408 100644 --- a/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt +++ b/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt @@ -5,7 +5,8 @@ Required properties: - gpios: specifies GPIO used for IR signal reception. Optional properties: - - linux,rc-map-name: Linux specific remote control map name. + - linux,rc-map-name: see rc.txt file in the same + directory. Example node: diff --git a/Documentation/devicetree/bindings/media/hix5hd2-ir.txt b/Documentation/devicetree/bindings/media/hix5hd2-ir.txt index fb5e7606643a..13ebc0fac9ea 100644 --- a/Documentation/devicetree/bindings/media/hix5hd2-ir.txt +++ b/Documentation/devicetree/bindings/media/hix5hd2-ir.txt @@ -8,10 +8,11 @@ Required properties: the device. The interrupt specifier format depends on the interrupt controller parent. - clocks: clock phandle and specifier pair. - - hisilicon,power-syscon: phandle of syscon used to control power. Optional properties: - - linux,rc-map-name : Remote control map name. + - linux,rc-map-name: see rc.txt file in the same directory. + - hisilicon,power-syscon: DEPRECATED. Don't use this in new dts files. + Provide correct clocks instead. Example node: @@ -19,7 +20,6 @@ Example node: compatible = "hisilicon,hix5hd2-ir"; reg = <0xf8001000 0x1000>; interrupts = <0 47 4>; - clocks = <&clock HIX5HD2_FIXED_24M>; - hisilicon,power-syscon = <&sysctrl>; + clocks = <&clock HIX5HD2_IR_CLOCK>; linux,rc-map-name = "rc-tivo"; }; diff --git a/Documentation/devicetree/bindings/media/i2c/ad5820.txt b/Documentation/devicetree/bindings/media/i2c/ad5820.txt new file mode 100644 index 000000000000..5940ca11c021 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ad5820.txt @@ -0,0 +1,19 @@ +* Analog Devices AD5820 autofocus coil + +Required Properties: + + - compatible: Must contain "adi,ad5820" + + - reg: I2C slave address + + - VANA-supply: supply of voltage for VANA pin + +Example: + + ad5820: coil@c { + compatible = "adi,ad5820"; + reg = <0x0c>; + + VANA-supply = <&vaux4>; + }; + diff --git a/Documentation/devicetree/bindings/media/i2c/adv7180.txt b/Documentation/devicetree/bindings/media/i2c/adv7180.txt new file mode 100644 index 000000000000..552b6a82cb1f --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adv7180.txt @@ -0,0 +1,49 @@ +* Analog Devices ADV7180 analog video decoder family + +The adv7180 family devices are used to capture analog video to different +digital interfaces like MIPI CSI-2 or parallel video. + +Required Properties : +- compatible : value must be one of + "adi,adv7180" + "adi,adv7180cp" + "adi,adv7180st" + "adi,adv7182" + "adi,adv7280" + "adi,adv7280-m" + "adi,adv7281" + "adi,adv7281-m" + "adi,adv7281-ma" + "adi,adv7282" + "adi,adv7282-m" + +Device nodes of "adi,adv7180cp" and "adi,adv7180st" must contain one +'port' child node per device input and output port, in accordance with the +video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. The port +nodes are numbered as follows. + + Port adv7180cp adv7180st +------------------------------------------------------------------- + Input 0-2 0-5 + Output 3 6 + +The digital output port node must contain at least one endpoint. + +Optional Properties : +- powerdown-gpios: reference to the GPIO connected to the powerdown pin, + if any. + + +Example: + + i2c0@1c22000 { + ... + ... + adv7180@21 { + compatible = "adi,adv7180"; + reg = <0x21>; + }; + ... + }; + diff --git a/Documentation/devicetree/bindings/media/i2c/adv748x.txt b/Documentation/devicetree/bindings/media/i2c/adv748x.txt new file mode 100644 index 000000000000..21ffb5ed8183 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adv748x.txt @@ -0,0 +1,95 @@ +* Analog Devices ADV748X video decoder with HDMI receiver + +The ADV7481 and ADV7482 are multi format video decoders with an integrated +HDMI receiver. They can output CSI-2 on two independent outputs TXA and TXB +from three input sources HDMI, analog and TTL. + +Required Properties: + + - compatible: Must contain one of the following + - "adi,adv7481" for the ADV7481 + - "adi,adv7482" for the ADV7482 + + - reg: I2C slave address + +Optional Properties: + + - interrupt-names: Should specify the interrupts as "intrq1", "intrq2" and/or + "intrq3". All interrupts are optional. The "intrq3" interrupt + is only available on the adv7481 + - interrupts: Specify the interrupt lines for the ADV748x + +The device node must contain one 'port' child node per device input and output +port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes +are numbered as follows. + + Name Type Port + --------------------------------------- + AIN0 sink 0 + AIN1 sink 1 + AIN2 sink 2 + AIN3 sink 3 + AIN4 sink 4 + AIN5 sink 5 + AIN6 sink 6 + AIN7 sink 7 + HDMI sink 8 + TTL sink 9 + TXA source 10 + TXB source 11 + +The digital output port nodes must contain at least one endpoint. + +Ports are optional if they are not connected to anything at the hardware level. + +Example: + + video-receiver@70 { + compatible = "adi,adv7482"; + reg = <0x70>; + + #address-cells = <1>; + #size-cells = <0>; + + interrupt-parent = <&gpio6>; + interrupt-names = "intrq1", "intrq2"; + interrupts = <30 IRQ_TYPE_LEVEL_LOW>, + <31 IRQ_TYPE_LEVEL_LOW>; + + port@7 { + reg = <7>; + + adv7482_ain7: endpoint { + remote-endpoint = <&cvbs_in>; + }; + }; + + port@8 { + reg = <8>; + + adv7482_hdmi: endpoint { + remote-endpoint = <&hdmi_in>; + }; + }; + + port@10 { + reg = <10>; + + adv7482_txa: endpoint { + clock-lanes = <0>; + data-lanes = <1 2 3 4>; + remote-endpoint = <&csi40_in>; + }; + }; + + port@11 { + reg = <11>; + + adv7482_txb: endpoint { + clock-lanes = <0>; + data-lanes = <1>; + remote-endpoint = <&csi20_in>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt b/Documentation/devicetree/bindings/media/i2c/adv7604.txt index 8337f75c75da..9cbd92eb5d05 100644 --- a/Documentation/devicetree/bindings/media/i2c/adv7604.txt +++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt @@ -34,6 +34,7 @@ The digital output port node must contain at least one endpoint. Optional Properties: - reset-gpios: Reference to the GPIO connected to the device's reset pin. + - default-input: Select which input is selected after reset. Optional Endpoint Properties: @@ -47,8 +48,6 @@ Optional Endpoint Properties: If none of hsync-active, vsync-active and pclk-sample is specified the endpoint will use embedded BT.656 synchronization. - - default-input: Select which input is selected after reset. - Example: hdmi_receiver@4c { diff --git a/Documentation/devicetree/bindings/media/i2c/max2175.txt b/Documentation/devicetree/bindings/media/i2c/max2175.txt new file mode 100644 index 000000000000..02b4e9cd7b1b --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/max2175.txt @@ -0,0 +1,59 @@ +Maxim Integrated MAX2175 RF to Bits tuner +----------------------------------------- + +The MAX2175 IC is an advanced analog/digital hybrid-radio receiver with +RF to Bits® front-end designed for software-defined radio solutions. + +Required properties: +-------------------- +- compatible: "maxim,max2175" for MAX2175 RF-to-bits tuner. +- clocks: clock specifier. +- port: child port node corresponding to the I2S output, in accordance with + the video interface bindings defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The port + node must contain at least one endpoint. + +Optional properties: +-------------------- +- maxim,master : phandle to the master tuner if it is a slave. This + is used to define two tuners in diversity mode + (1 master, 1 slave). By default each tuner is an + individual master. +- maxim,refout-load : load capacitance value (in picofarads) on reference + output drive level. The possible load values are: + 0 (default - refout disabled) + 10 + 20 + 30 + 40 + 60 + 70 +- maxim,am-hiz-filter : empty property indicates the AM Hi-Z filter is used + in this hardware for AM antenna input. + +Example: +-------- + +Board specific DTS file + +/* Fixed XTAL clock node */ +maxim_xtal: clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <36864000>; +}; + +/* A tuner device instance under i2c bus */ +max2175_0: tuner@60 { + compatible = "maxim,max2175"; + reg = <0x60>; + clocks = <&maxim_xtal>; + maxim,refout-load = <10>; + + port { + max2175_0_ep: endpoint { + remote-endpoint = <&slave_rx_device>; + }; + }; + +}; diff --git a/Documentation/devicetree/bindings/media/i2c/mt9v032.txt b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt index 202565313e82..100f0ae43269 100644 --- a/Documentation/devicetree/bindings/media/i2c/mt9v032.txt +++ b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt @@ -20,6 +20,8 @@ Optional Properties: - link-frequencies: List of allowed link frequencies in Hz. Each frequency is expressed as a 64-bit big-endian integer. +- reset-gpios: GPIO handle which is connected to the reset pin of the chip. +- standby-gpios: GPIO handle which is connected to the standby pin of the chip. For further reading on port node refer to Documentation/devicetree/bindings/media/video-interfaces.txt. diff --git a/Documentation/devicetree/bindings/media/i2c/ov2640.txt b/Documentation/devicetree/bindings/media/i2c/ov2640.txt index c429b5bdcaa0..989ce6cb6ac3 100644 --- a/Documentation/devicetree/bindings/media/i2c/ov2640.txt +++ b/Documentation/devicetree/bindings/media/i2c/ov2640.txt @@ -1,8 +1,8 @@ * Omnivision OV2640 CMOS sensor -The Omnivision OV2640 sensor support multiple resolutions output, such as -CIF, SVGA, UXGA. It also can support YUV422/420, RGB565/555 or raw RGB -output format. +The Omnivision OV2640 sensor supports multiple resolutions output, such as +CIF, SVGA, UXGA. It also can support the YUV422/420, RGB565/555 or raw RGB +output formats. Required Properties: - compatible: should be "ovti,ov2640" @@ -20,26 +20,21 @@ Documentation/devicetree/bindings/media/video-interfaces.txt. Example: i2c1: i2c@f0018000 { - ov2640: camera@0x30 { + ov2640: camera@30 { compatible = "ovti,ov2640"; reg = <0x30>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_pck1 &pinctrl_ov2640_pwdn &pinctrl_ov2640_resetb>; - - resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>; - pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>; - - clocks = <&pck1>; + pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>; + resetb-gpios = <&pioE 11 GPIO_ACTIVE_LOW>; + pwdn-gpios = <&pioE 13 GPIO_ACTIVE_HIGH>; + clocks = <&pck0>; clock-names = "xvclk"; - - assigned-clocks = <&pck1>; + assigned-clocks = <&pck0>; assigned-clock-rates = <25000000>; port { ov2640_0: endpoint { remote-endpoint = <&isi_0>; - bus-width = <8>; }; }; }; diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.txt b/Documentation/devicetree/bindings/media/i2c/ov5640.txt new file mode 100644 index 000000000000..540b36c4b1f2 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov5640.txt @@ -0,0 +1,45 @@ +* Omnivision OV5640 MIPI CSI-2 sensor + +Required Properties: +- compatible: should be "ovti,ov5640" +- clocks: reference to the xclk input clock. +- clock-names: should be "xclk". +- DOVDD-supply: Digital I/O voltage supply, 1.8 volts +- AVDD-supply: Analog voltage supply, 2.8 volts +- DVDD-supply: Digital core voltage supply, 1.5 volts + +Optional Properties: +- reset-gpios: reference to the GPIO connected to the reset pin, if any. + This is an active low signal to the OV5640. +- powerdown-gpios: reference to the GPIO connected to the powerdown pin, + if any. This is an active high signal to the OV5640. + +The device node must contain one 'port' child node for its digital output +video port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + +&i2c1 { + ov5640: camera@3c { + compatible = "ovti,ov5640"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ov5640>; + reg = <0x3c>; + clocks = <&clks IMX6QDL_CLK_CKO>; + clock-names = "xclk"; + DOVDD-supply = <&vgen4_reg>; /* 1.8v */ + AVDD-supply = <&vgen3_reg>; /* 2.8v */ + DVDD-supply = <&vgen2_reg>; /* 1.5v */ + powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; + + port { + ov5640_to_mipi_csi2: endpoint { + remote-endpoint = <&mipi_csi2_from_ov5640>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/i2c/ov5645.txt b/Documentation/devicetree/bindings/media/i2c/ov5645.txt new file mode 100644 index 000000000000..fd7aec9f8e24 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov5645.txt @@ -0,0 +1,54 @@ +* Omnivision 1/4-Inch 5Mp CMOS Digital Image Sensor + +The Omnivision OV5645 is a 1/4-Inch CMOS active pixel digital image sensor with +an active array size of 2592H x 1944V. It is programmable through a serial I2C +interface. + +Required Properties: +- compatible: Value should be "ovti,ov5645". +- clocks: Reference to the xclk clock. +- clock-names: Should be "xclk". +- clock-frequency: Frequency of the xclk clock. +- enable-gpios: Chip enable GPIO. Polarity is GPIO_ACTIVE_HIGH. This corresponds + to the hardware pin PWDNB which is physically active low. +- reset-gpios: Chip reset GPIO. Polarity is GPIO_ACTIVE_LOW. This corresponds to + the hardware pin RESETB. +- vdddo-supply: Chip digital IO regulator. +- vdda-supply: Chip analog regulator. +- vddd-supply: Chip digital core regulator. + +The device node must contain one 'port' child node for its digital output +video port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + &i2c1 { + ... + + ov5645: ov5645@78 { + compatible = "ovti,ov5645"; + reg = <0x78>; + + enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio5 20 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&camera_rear_default>; + + clocks = <&clks 200>; + clock-names = "xclk"; + clock-frequency = <23880000>; + + vdddo-supply = <&camera_dovdd_1v8>; + vdda-supply = <&camera_avdd_2v8>; + vddd-supply = <&camera_dvdd_1v2>; + + port { + ov5645_ep: endpoint { + clock-lanes = <1>; + data-lanes = <0 2>; + remote-endpoint = <&csi0_ep>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ov5647.txt b/Documentation/devicetree/bindings/media/i2c/ov5647.txt new file mode 100644 index 000000000000..22e44945b661 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov5647.txt @@ -0,0 +1,35 @@ +Omnivision OV5647 raw image sensor +--------------------------------- + +OV5647 is a raw image sensor with MIPI CSI-2 and CCP2 image data interfaces +and CCI (I2C compatible) control bus. + +Required properties: + +- compatible : "ovti,ov5647". +- reg : I2C slave address of the sensor. +- clocks : Reference to the xclk clock. + +The common video interfaces bindings (see video-interfaces.txt) should be +used to specify link to the image data receiver. The OV5647 device +node should contain one 'port' child node with an 'endpoint' subnode. + +Endpoint node mandatory properties: + +- remote-endpoint: A phandle to the bus receiver's endpoint node. + +Example: + + i2c@2000 { + ... + ov: camera@36 { + compatible = "ovti,ov5647"; + reg = <0x36>; + clocks = <&camera_clk>; + port { + camera_1: endpoint { + remote-endpoint = <&csi1_ep1>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ov7670.txt b/Documentation/devicetree/bindings/media/i2c/ov7670.txt new file mode 100644 index 000000000000..826b6563b009 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov7670.txt @@ -0,0 +1,43 @@ +* Omnivision OV7670 CMOS sensor + +The Omnivision OV7670 sensor supports multiple resolutions output, such as +CIF, SVGA, UXGA. It also can support the YUV422/420, RGB565/555 or raw RGB +output formats. + +Required Properties: +- compatible: should be "ovti,ov7670" +- clocks: reference to the xclk input clock. +- clock-names: should be "xclk". + +Optional Properties: +- reset-gpios: reference to the GPIO connected to the resetb pin, if any. + Active is low. +- powerdown-gpios: reference to the GPIO connected to the pwdn pin, if any. + Active is high. + +The device node must contain one 'port' child node for its digital output +video port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + i2c1: i2c@f0018000 { + ov7670: camera@21 { + compatible = "ovti,ov7670"; + reg = <0x21>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>; + reset-gpios = <&pioE 11 GPIO_ACTIVE_LOW>; + powerdown-gpios = <&pioE 13 GPIO_ACTIVE_HIGH>; + clocks = <&pck0>; + clock-names = "xclk"; + assigned-clocks = <&pck0>; + assigned-clock-rates = <25000000>; + + port { + ov7670_0: endpoint { + remote-endpoint = <&isi_0>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt b/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt new file mode 100644 index 000000000000..0b7b6a4d84ff --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt @@ -0,0 +1,48 @@ +Toshiba et8ek8 5MP sensor + +Toshiba et8ek8 5MP sensor is an image sensor found in Nokia N900 device + +More detailed documentation can be found in +Documentation/devicetree/bindings/media/video-interfaces.txt . + + +Mandatory properties +-------------------- + +- compatible: "toshiba,et8ek8" +- reg: I2C address (0x3e, or an alternative address) +- vana-supply: Analogue voltage supply (VANA), 2.8 volts +- clocks: External clock to the sensor +- clock-frequency: Frequency of the external clock to the sensor. Camera + driver will set this frequency on the external clock. The clock frequency is + a pre-determined frequency known to be suitable to the board. +- reset-gpios: XSHUTDOWN GPIO. The XSHUTDOWN signal is active low. The sensor + is in hardware standby mode when the signal is in the low state. + + +Endpoint node mandatory properties +---------------------------------- + +- remote-endpoint: A phandle to the bus receiver's endpoint node. + + +Example +------- + +&i2c3 { + clock-frequency = <400000>; + + cam1: camera@3e { + compatible = "toshiba,et8ek8"; + reg = <0x3e>; + vana-supply = <&vaux4>; + clocks = <&isp 0>; + clock-frequency = <9600000>; + reset-gpio = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* 102 */ + port { + csi_cam1: endpoint { + remote-endpoint = <&csi_out1>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt new file mode 100644 index 000000000000..8c0fc1a26bf0 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt @@ -0,0 +1,45 @@ +* Texas Instruments TVP5150 and TVP5151 video decoders + +The TVP5150 and TVP5151 are video decoders that convert baseband NTSC and PAL +(and also SECAM in the TVP5151 case) video signals to either 8-bit 4:2:2 YUV +with discrete syncs or 8-bit ITU-R BT.656 with embedded syncs output formats. + +Required Properties: +- compatible: value must be "ti,tvp5150" +- reg: I2C slave address + +Optional Properties: +- pdn-gpios: phandle for the GPIO connected to the PDN pin, if any. +- reset-gpios: phandle for the GPIO connected to the RESETB pin, if any. + +The device node must contain one 'port' child node for its digital output +video port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Required Endpoint Properties for parallel synchronization: + +- hsync-active: active state of the HSYNC signal. Must be <1> (HIGH). +- vsync-active: active state of the VSYNC signal. Must be <1> (HIGH). +- field-even-active: field signal level during the even field data + transmission. Must be <0>. + +If none of hsync-active, vsync-active and field-even-active is specified, +the endpoint is assumed to use embedded BT.656 synchronization. + +Example: + +&i2c2 { + ... + tvp5150@5c { + compatible = "ti,tvp5150"; + reg = <0x5c>; + pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>; + + port { + tvp5150_1: endpoint { + remote-endpoint = <&ccdc_ep>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/imx.txt b/Documentation/devicetree/bindings/media/imx.txt new file mode 100644 index 000000000000..77f4b0a7fd2b --- /dev/null +++ b/Documentation/devicetree/bindings/media/imx.txt @@ -0,0 +1,53 @@ +Freescale i.MX Media Video Device +================================= + +Video Media Controller node +--------------------------- + +This is the media controller node for video capture support. It is a +virtual device that lists the camera serial interface nodes that the +media device will control. + +Required properties: +- compatible : "fsl,imx-capture-subsystem"; +- ports : Should contain a list of phandles pointing to camera + sensor interface ports of IPU devices + +example: + +capture-subsystem { + compatible = "fsl,imx-capture-subsystem"; + ports = <&ipu1_csi0>, <&ipu1_csi1>; +}; + + +mipi_csi2 node +-------------- + +This is the device node for the MIPI CSI-2 Receiver core in the i.MX +SoC. This is a Synopsys Designware MIPI CSI-2 host controller core +combined with a D-PHY core mixed into the same register block. In +addition this device consists of an i.MX-specific "CSI2IPU gasket" +glue logic, also controlled from the same register block. The CSI2IPU +gasket demultiplexes the four virtual channel streams from the host +controller's 32-bit output image bus onto four 16-bit parallel busses +to the i.MX IPU CSIs. + +Required properties: +- compatible : "fsl,imx6-mipi-csi2"; +- reg : physical base address and length of the register set; +- clocks : the MIPI CSI-2 receiver requires three clocks: hsi_tx + (the D-PHY clock), video_27m (D-PHY PLL reference + clock), and eim_podf; +- clock-names : must contain "dphy", "ref", "pix"; +- port@* : five port nodes must exist, containing endpoints + connecting to the source and sink devices according to + of_graph bindings. The first port is an input port, + connecting with a MIPI CSI-2 source, and ports 1 + through 4 are output ports connecting with parallel + bus sink endpoint nodes and correspond to the four + MIPI CSI-2 virtual channel outputs. + +Optional properties: +- interrupts : must contain two level-triggered interrupts, + in order: 100 and 101; diff --git a/Documentation/devicetree/bindings/media/mediatek-jpeg-decoder.txt b/Documentation/devicetree/bindings/media/mediatek-jpeg-decoder.txt new file mode 100644 index 000000000000..3813947b4d4f --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek-jpeg-decoder.txt @@ -0,0 +1,37 @@ +* Mediatek JPEG Decoder + +Mediatek JPEG Decoder is the JPEG decode hardware present in Mediatek SoCs + +Required properties: +- compatible : must be one of the following string: + "mediatek,mt8173-jpgdec" + "mediatek,mt2701-jpgdec" +- reg : physical base address of the jpeg decoder registers and length of + memory mapped region. +- interrupts : interrupt number to the interrupt controller. +- clocks: device clocks, see + Documentation/devicetree/bindings/clock/clock-bindings.txt for details. +- clock-names: must contain "jpgdec-smi" and "jpgdec". +- power-domains: a phandle to the power domain, see + Documentation/devicetree/bindings/power/power_domain.txt for details. +- mediatek,larb: must contain the local arbiters in the current Socs, see + Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt + for details. +- iommus: should point to the respective IOMMU block with master port as + argument, see Documentation/devicetree/bindings/iommu/mediatek,iommu.txt + for details. + +Example: + jpegdec: jpegdec@15004000 { + compatible = "mediatek,mt2701-jpgdec"; + reg = <0 0x15004000 0 0x1000>; + interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_LOW>; + clocks = <&imgsys CLK_IMG_JPGDEC_SMI>, + <&imgsys CLK_IMG_JPGDEC>; + clock-names = "jpgdec-smi", + "jpgdec"; + power-domains = <&scpsys MT2701_POWER_DOMAIN_ISP>; + mediatek,larb = <&larb2>; + iommus = <&iommu MT2701_M4U_PORT_JPGDEC_WDMA>, + <&iommu MT2701_M4U_PORT_JPGDEC_BSDMA>; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek-mdp.txt b/Documentation/devicetree/bindings/media/mediatek-mdp.txt new file mode 100644 index 000000000000..0d03e3ae2be2 --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek-mdp.txt @@ -0,0 +1,103 @@ +* Mediatek Media Data Path + +Media Data Path is used for scaling and color space conversion. + +Required properties (controller node): +- compatible: "mediatek,mt8173-mdp" +- mediatek,vpu: the node of video processor unit, see + Documentation/devicetree/bindings/media/mediatek-vpu.txt for details. + +Required properties (all function blocks, child node): +- compatible: Should be one of + "mediatek,mt8173-mdp-rdma" - read DMA + "mediatek,mt8173-mdp-rsz" - resizer + "mediatek,mt8173-mdp-wdma" - write DMA + "mediatek,mt8173-mdp-wrot" - write DMA with rotation +- reg: Physical base address and length of the function block register space +- clocks: device clocks, see + Documentation/devicetree/bindings/clock/clock-bindings.txt for details. +- power-domains: a phandle to the power domain, see + Documentation/devicetree/bindings/power/power_domain.txt for details. + +Required properties (DMA function blocks, child node): +- compatible: Should be one of + "mediatek,mt8173-mdp-rdma" + "mediatek,mt8173-mdp-wdma" + "mediatek,mt8173-mdp-wrot" +- iommus: should point to the respective IOMMU block with master port as + argument, see Documentation/devicetree/bindings/iommu/mediatek,iommu.txt + for details. +- mediatek,larb: must contain the local arbiters in the current Socs, see + Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt + for details. + +Example: + mdp_rdma0: rdma@14001000 { + compatible = "mediatek,mt8173-mdp-rdma"; + "mediatek,mt8173-mdp"; + reg = <0 0x14001000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_RDMA0>, + <&mmsys CLK_MM_MUTEX_32K>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + iommus = <&iommu M4U_PORT_MDP_RDMA0>; + mediatek,larb = <&larb0>; + mediatek,vpu = <&vpu>; + }; + + mdp_rdma1: rdma@14002000 { + compatible = "mediatek,mt8173-mdp-rdma"; + reg = <0 0x14002000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_RDMA1>, + <&mmsys CLK_MM_MUTEX_32K>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + iommus = <&iommu M4U_PORT_MDP_RDMA1>; + mediatek,larb = <&larb4>; + }; + + mdp_rsz0: rsz@14003000 { + compatible = "mediatek,mt8173-mdp-rsz"; + reg = <0 0x14003000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_RSZ0>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + }; + + mdp_rsz1: rsz@14004000 { + compatible = "mediatek,mt8173-mdp-rsz"; + reg = <0 0x14004000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_RSZ1>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + }; + + mdp_rsz2: rsz@14005000 { + compatible = "mediatek,mt8173-mdp-rsz"; + reg = <0 0x14005000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_RSZ2>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + }; + + mdp_wdma0: wdma@14006000 { + compatible = "mediatek,mt8173-mdp-wdma"; + reg = <0 0x14006000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_WDMA>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + iommus = <&iommu M4U_PORT_MDP_WDMA>; + mediatek,larb = <&larb0>; + }; + + mdp_wrot0: wrot@14007000 { + compatible = "mediatek,mt8173-mdp-wrot"; + reg = <0 0x14007000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_WROT0>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + iommus = <&iommu M4U_PORT_MDP_WROT0>; + mediatek,larb = <&larb0>; + }; + + mdp_wrot1: wrot@14008000 { + compatible = "mediatek,mt8173-mdp-wrot"; + reg = <0 0x14008000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_WROT1>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + iommus = <&iommu M4U_PORT_MDP_WROT1>; + mediatek,larb = <&larb4>; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek-vcodec.txt b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt new file mode 100644 index 000000000000..46c15c54175d --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt @@ -0,0 +1,108 @@ +Mediatek Video Codec + +Mediatek Video Codec is the video codec hw present in Mediatek SoCs which +supports high resolution encoding and decoding functionalities. + +Required properties: +- compatible : "mediatek,mt8173-vcodec-enc" for encoder + "mediatek,mt8173-vcodec-dec" for decoder. +- reg : Physical base address of the video codec registers and length of + memory mapped region. +- interrupts : interrupt number to the cpu. +- mediatek,larb : must contain the local arbiters in the current Socs. +- clocks : list of clock specifiers, corresponding to entries in + the clock-names property. +- clock-names: encoder must contain "venc_sel_src", "venc_sel",, + "venc_lt_sel_src", "venc_lt_sel", decoder must contain "vcodecpll", + "univpll_d2", "clk_cci400_sel", "vdec_sel", "vdecpll", "vencpll", + "venc_lt_sel", "vdec_bus_clk_src". +- iommus : should point to the respective IOMMU block with master port as + argument, see Documentation/devicetree/bindings/iommu/mediatek,iommu.txt + for details. +- mediatek,vpu : the node of video processor unit + + +Example: + +vcodec_dec: vcodec@16000000 { + compatible = "mediatek,mt8173-vcodec-dec"; + reg = <0 0x16000000 0 0x100>, /*VDEC_SYS*/ + <0 0x16020000 0 0x1000>, /*VDEC_MISC*/ + <0 0x16021000 0 0x800>, /*VDEC_LD*/ + <0 0x16021800 0 0x800>, /*VDEC_TOP*/ + <0 0x16022000 0 0x1000>, /*VDEC_CM*/ + <0 0x16023000 0 0x1000>, /*VDEC_AD*/ + <0 0x16024000 0 0x1000>, /*VDEC_AV*/ + <0 0x16025000 0 0x1000>, /*VDEC_PP*/ + <0 0x16026800 0 0x800>, /*VP8_VD*/ + <0 0x16027000 0 0x800>, /*VP6_VD*/ + <0 0x16027800 0 0x800>, /*VP8_VL*/ + <0 0x16028400 0 0x400>; /*VP9_VD*/ + interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_LOW>; + mediatek,larb = <&larb1>; + iommus = <&iommu M4U_PORT_HW_VDEC_MC_EXT>, + <&iommu M4U_PORT_HW_VDEC_PP_EXT>, + <&iommu M4U_PORT_HW_VDEC_AVC_MV_EXT>, + <&iommu M4U_PORT_HW_VDEC_PRED_RD_EXT>, + <&iommu M4U_PORT_HW_VDEC_PRED_WR_EXT>, + <&iommu M4U_PORT_HW_VDEC_UFO_EXT>, + <&iommu M4U_PORT_HW_VDEC_VLD_EXT>, + <&iommu M4U_PORT_HW_VDEC_VLD2_EXT>; + mediatek,vpu = <&vpu>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_VDEC>; + clocks = <&apmixedsys CLK_APMIXED_VCODECPLL>, + <&topckgen CLK_TOP_UNIVPLL_D2>, + <&topckgen CLK_TOP_CCI400_SEL>, + <&topckgen CLK_TOP_VDEC_SEL>, + <&topckgen CLK_TOP_VCODECPLL>, + <&apmixedsys CLK_APMIXED_VENCPLL>, + <&topckgen CLK_TOP_VENC_LT_SEL>, + <&topckgen CLK_TOP_VCODECPLL_370P5>; + clock-names = "vcodecpll", + "univpll_d2", + "clk_cci400_sel", + "vdec_sel", + "vdecpll", + "vencpll", + "venc_lt_sel", + "vdec_bus_clk_src"; + }; + + vcodec_enc: vcodec@0x18002000 { + compatible = "mediatek,mt8173-vcodec-enc"; + reg = <0 0x18002000 0 0x1000>, /*VENC_SYS*/ + <0 0x19002000 0 0x1000>; /*VENC_LT_SYS*/ + interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 202 IRQ_TYPE_LEVEL_LOW>; + mediatek,larb = <&larb3>, + <&larb5>; + iommus = <&iommu M4U_PORT_VENC_RCPU>, + <&iommu M4U_PORT_VENC_REC>, + <&iommu M4U_PORT_VENC_BSDMA>, + <&iommu M4U_PORT_VENC_SV_COMV>, + <&iommu M4U_PORT_VENC_RD_COMV>, + <&iommu M4U_PORT_VENC_CUR_LUMA>, + <&iommu M4U_PORT_VENC_CUR_CHROMA>, + <&iommu M4U_PORT_VENC_REF_LUMA>, + <&iommu M4U_PORT_VENC_REF_CHROMA>, + <&iommu M4U_PORT_VENC_NBM_RDMA>, + <&iommu M4U_PORT_VENC_NBM_WDMA>, + <&iommu M4U_PORT_VENC_RCPU_SET2>, + <&iommu M4U_PORT_VENC_REC_FRM_SET2>, + <&iommu M4U_PORT_VENC_BSDMA_SET2>, + <&iommu M4U_PORT_VENC_SV_COMA_SET2>, + <&iommu M4U_PORT_VENC_RD_COMA_SET2>, + <&iommu M4U_PORT_VENC_CUR_LUMA_SET2>, + <&iommu M4U_PORT_VENC_CUR_CHROMA_SET2>, + <&iommu M4U_PORT_VENC_REF_LUMA_SET2>, + <&iommu M4U_PORT_VENC_REC_CHROMA_SET2>; + mediatek,vpu = <&vpu>; + clocks = <&topckgen CLK_TOP_VENCPLL_D2>, + <&topckgen CLK_TOP_VENC_SEL>, + <&topckgen CLK_TOP_UNIVPLL1_D2>, + <&topckgen CLK_TOP_VENC_LT_SEL>; + clock-names = "venc_sel_src", + "venc_sel", + "venc_lt_sel_src", + "venc_lt_sel"; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek-vpu.txt b/Documentation/devicetree/bindings/media/mediatek-vpu.txt new file mode 100644 index 000000000000..2a5bac37f9a2 --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek-vpu.txt @@ -0,0 +1,31 @@ +* Mediatek Video Processor Unit + +Video Processor Unit is a HW video controller. It controls HW Codec including +H.264/VP8/VP9 Decode, H.264/VP8 Encode and Image Processor (scale/rotate/color convert). + +Required properties: + - compatible: "mediatek,mt8173-vpu" + - reg: Must contain an entry for each entry in reg-names. + - reg-names: Must include the following entries: + "tcm": tcm base + "cfg_reg": Main configuration registers base + - interrupts: interrupt number to the cpu. + - clocks : clock name from clock manager + - clock-names: must be main. It is the main clock of VPU + +Optional properties: + - memory-region: phandle to a node describing memory (see + Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt) + to be used for VPU extended memory; if not present, VPU may be located + anywhere in the memory + +Example: + vpu: vpu@10020000 { + compatible = "mediatek,mt8173-vpu"; + reg = <0 0x10020000 0 0x30000>, + <0 0x10050000 0 0x100>; + reg-names = "tcm", "cfg_reg"; + interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&topckgen TOP_SCP_SEL>; + clock-names = "main"; + }; diff --git a/Documentation/devicetree/bindings/media/meson-ir.txt b/Documentation/devicetree/bindings/media/meson-ir.txt index 407848e85f31..efd9d29a8f10 100644 --- a/Documentation/devicetree/bindings/media/meson-ir.txt +++ b/Documentation/devicetree/bindings/media/meson-ir.txt @@ -1,10 +1,16 @@ * Amlogic Meson IR remote control receiver Required properties: - - compatible : should be "amlogic,meson6-ir" + - compatible : depending on the platform this should be one of: + - "amlogic,meson6-ir" + - "amlogic,meson8b-ir" + - "amlogic,meson-gxbb-ir" - reg : physical base address and length of the device registers - interrupts : a single specifier for the interrupt from the device +Optional properties: + - linux,rc-map-name: see rc.txt file in the same directory. + Example: ir-receiver@c8100480 { diff --git a/Documentation/devicetree/bindings/media/mtk-cir.txt b/Documentation/devicetree/bindings/media/mtk-cir.txt new file mode 100644 index 000000000000..2be2005577d6 --- /dev/null +++ b/Documentation/devicetree/bindings/media/mtk-cir.txt @@ -0,0 +1,24 @@ +Device-Tree bindings for Mediatek consumer IR controller +found in Mediatek SoC family + +Required properties: +- compatible : "mediatek,mt7623-cir" +- clocks : list of clock specifiers, corresponding to + entries in clock-names property; +- clock-names : should contain "clk" entries; +- interrupts : should contain IR IRQ number; +- reg : should contain IO map address for IR. + +Optional properties: +- linux,rc-map-name : see rc.txt file in the same directory. + +Example: + +cir: cir@10013000 { + compatible = "mediatek,mt7623-cir"; + reg = <0 0x10013000 0 0x1000>; + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_INFRA_IRRX>; + clock-names = "clk"; + linux,rc-map-name = "rc-rc6-mce"; +}; diff --git a/Documentation/devicetree/bindings/media/nokia,n900-ir b/Documentation/devicetree/bindings/media/nokia,n900-ir new file mode 100644 index 000000000000..13a18ce37dd1 --- /dev/null +++ b/Documentation/devicetree/bindings/media/nokia,n900-ir @@ -0,0 +1,20 @@ +Device-Tree bindings for LIRC TX driver for Nokia N900(RX51) + +Required properties: + - compatible: should be "nokia,n900-ir". + - pwms: specifies PWM used for IR signal transmission. + +Example node: + + pwm9: dmtimer-pwm@9 { + compatible = "ti,omap-dmtimer-pwm"; + ti,timers = <&timer9>; + ti,clock-source = <0x00>; /* timer_sys_ck */ + #pwm-cells = <3>; + }; + + ir: n900-ir { + compatible = "nokia,n900-ir"; + + pwms = <&pwm9 0 26316 0>; /* 38000 Hz */ + }; diff --git a/Documentation/devicetree/bindings/media/qcom,venus.txt b/Documentation/devicetree/bindings/media/qcom,venus.txt new file mode 100644 index 000000000000..2693449daf73 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,venus.txt @@ -0,0 +1,107 @@ +* Qualcomm Venus video encoder/decoder accelerators + +- compatible: + Usage: required + Value type: <stringlist> + Definition: Value should contain one of: + - "qcom,msm8916-venus" + - "qcom,msm8996-venus" +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: Register base address and length of the register map. +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: Should contain interrupt line number. +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: A List of phandle and clock specifier pairs as listed + in clock-names property. +- clock-names: + Usage: required for msm8916 + Value type: <stringlist> + Definition: Should contain the following entries: + - "core" Core video accelerator clock + - "iface" Video accelerator AHB clock + - "bus" Video accelerator AXI clock +- clock-names: + Usage: required for msm8996 + Value type: <stringlist> + Definition: Should contain the following entries: + - "core" Core video accelerator clock + - "iface" Video accelerator AHB clock + - "bus" Video accelerator AXI clock + - "mbus" Video MAXI clock +- power-domains: + Usage: required + Value type: <prop-encoded-array> + Definition: A phandle and power domain specifier pairs to the + power domain which is responsible for collapsing + and restoring power to the peripheral. +- iommus: + Usage: required + Value type: <prop-encoded-array> + Definition: A list of phandle and IOMMU specifier pairs. +- memory-region: + Usage: required + Value type: <phandle> + Definition: reference to the reserved-memory for the firmware + memory region. + +* Subnodes +The Venus video-codec node must contain two subnodes representing +video-decoder and video-encoder. + +Every of video-encoder or video-decoder subnode should have: + +- compatible: + Usage: required + Value type: <stringlist> + Definition: Value should contain "venus-decoder" or "venus-encoder" +- clocks: + Usage: required for msm8996 + Value type: <prop-encoded-array> + Definition: A List of phandle and clock specifier pairs as listed + in clock-names property. +- clock-names: + Usage: required for msm8996 + Value type: <stringlist> + Definition: Should contain the following entries: + - "core" Subcore video accelerator clock + +- power-domains: + Usage: required for msm8996 + Value type: <prop-encoded-array> + Definition: A phandle and power domain specifier pairs to the + power domain which is responsible for collapsing + and restoring power to the subcore. + +* An Example + video-codec@1d00000 { + compatible = "qcom,msm8916-venus"; + reg = <0x01d00000 0xff000>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_VENUS0_VCODEC0_CLK>, + <&gcc GCC_VENUS0_AHB_CLK>, + <&gcc GCC_VENUS0_AXI_CLK>; + clock-names = "core", "iface", "bus"; + power-domains = <&gcc VENUS_GDSC>; + iommus = <&apps_iommu 5>; + memory-region = <&venus_mem>; + + video-decoder { + compatible = "venus-decoder"; + clocks = <&mmcc VIDEO_SUBCORE0_CLK>; + clock-names = "core"; + power-domains = <&mmcc VENUS_CORE0_GDSC>; + }; + + video-encoder { + compatible = "venus-encoder"; + clocks = <&mmcc VIDEO_SUBCORE1_CLK>; + clock-names = "core"; + power-domains = <&mmcc VENUS_CORE1_GDSC>; + }; + }; diff --git a/Documentation/devicetree/bindings/media/rc.txt b/Documentation/devicetree/bindings/media/rc.txt new file mode 100644 index 000000000000..d3e7a012bfda --- /dev/null +++ b/Documentation/devicetree/bindings/media/rc.txt @@ -0,0 +1,117 @@ +The following properties are common to the infrared remote controllers: + +- linux,rc-map-name: string, specifies the scancode/key mapping table + defined in-kernel for the remote controller. Support values are: + * "rc-adstech-dvb-t-pci" + * "rc-alink-dtu-m" + * "rc-anysee" + * "rc-apac-viewcomp" + * "rc-asus-pc39" + * "rc-asus-ps3-100" + * "rc-ati-tv-wonder-hd-600" + * "rc-ati-x10" + * "rc-avermedia-a16d" + * "rc-avermedia-cardbus" + * "rc-avermedia-dvbt" + * "rc-avermedia-m135a" + * "rc-avermedia-m733a-rm-k6" + * "rc-avermedia-rm-ks" + * "rc-avermedia" + * "rc-avertv-303" + * "rc-azurewave-ad-tu700" + * "rc-behold-columbus" + * "rc-behold" + * "rc-budget-ci-old" + * "rc-cec" + * "rc-cinergy-1400" + * "rc-cinergy" + * "rc-delock-61959" + * "rc-dib0700-nec" + * "rc-dib0700-rc5" + * "rc-digitalnow-tinytwin" + * "rc-digittrade" + * "rc-dm1105-nec" + * "rc-dntv-live-dvbt-pro" + * "rc-dntv-live-dvb-t" + * "rc-dtt200u" + * "rc-dvbsky" + * "rc-empty" + * "rc-em-terratec" + * "rc-encore-enltv2" + * "rc-encore-enltv-fm53" + * "rc-encore-enltv" + * "rc-evga-indtube" + * "rc-eztv" + * "rc-flydvb" + * "rc-flyvideo" + * "rc-fusionhdtv-mce" + * "rc-gadmei-rm008z" + * "rc-geekbox" + * "rc-genius-tvgo-a11mce" + * "rc-gotview7135" + * "rc-hauppauge" + * "rc-imon-mce" + * "rc-imon-pad" + * "rc-iodata-bctv7e" + * "rc-it913x-v1" + * "rc-it913x-v2" + * "rc-kaiomy" + * "rc-kworld-315u" + * "rc-kworld-pc150u" + * "rc-kworld-plus-tv-analog" + * "rc-leadtek-y04g0051" + * "rc-lirc" + * "rc-lme2510" + * "rc-manli" + * "rc-medion-x10" + * "rc-medion-x10-digitainer" + * "rc-medion-x10-or2x" + * "rc-msi-digivox-ii" + * "rc-msi-digivox-iii" + * "rc-msi-tvanywhere-plus" + * "rc-msi-tvanywhere" + * "rc-nebula" + * "rc-nec-terratec-cinergy-xs" + * "rc-norwood" + * "rc-npgtech" + * "rc-pctv-sedna" + * "rc-pinnacle-color" + * "rc-pinnacle-grey" + * "rc-pinnacle-pctv-hd" + * "rc-pixelview-new" + * "rc-pixelview" + * "rc-pixelview-002t" + * "rc-pixelview-mk12" + * "rc-powercolor-real-angel" + * "rc-proteus-2309" + * "rc-purpletv" + * "rc-pv951" + * "rc-hauppauge" + * "rc-rc5-tv" + * "rc-rc6-mce" + * "rc-real-audio-220-32-keys" + * "rc-reddo" + * "rc-snapstream-firefly" + * "rc-streamzap" + * "rc-tbs-nec" + * "rc-technisat-ts35" + * "rc-technisat-usb2" + * "rc-terratec-cinergy-c-pci" + * "rc-terratec-cinergy-s2-hd" + * "rc-terratec-cinergy-xs" + * "rc-terratec-slim" + * "rc-terratec-slim-2" + * "rc-tevii-nec" + * "rc-tivo" + * "rc-total-media-in-hand" + * "rc-total-media-in-hand-02" + * "rc-trekstor" + * "rc-tt-1500" + * "rc-twinhan-dtv-cab-ci" + * "rc-twinhan1027" + * "rc-videomate-k100" + * "rc-videomate-s350" + * "rc-videomate-tv-pvr" + * "rc-winfast" + * "rc-winfast-usbii-deluxe" + * "rc-su3000" diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt b/Documentation/devicetree/bindings/media/rcar_vin.txt index 9dafe6b06cd2..6e4ef8caf759 100644 --- a/Documentation/devicetree/bindings/media/rcar_vin.txt +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt @@ -1,17 +1,26 @@ -Renesas RCar Video Input driver (rcar_vin) ------------------------------------------- +Renesas R-Car Video Input driver (rcar_vin) +------------------------------------------- The rcar_vin device provides video input capabilities for the Renesas R-Car family of devices. The current blocks are always slaves and suppot one input channel which can be either RGB, YUYV or BT656. - - compatible: Must be one of the following + - compatible: Must be one or more of the following + - "renesas,vin-r8a7795" for the R8A7795 device - "renesas,vin-r8a7794" for the R8A7794 device - "renesas,vin-r8a7793" for the R8A7793 device + - "renesas,vin-r8a7792" for the R8A7792 device - "renesas,vin-r8a7791" for the R8A7791 device - "renesas,vin-r8a7790" for the R8A7790 device - "renesas,vin-r8a7779" for the R8A7779 device - "renesas,vin-r8a7778" for the R8A7778 device + - "renesas,rcar-gen2-vin" for a generic R-Car Gen2 compatible device. + - "renesas,rcar-gen3-vin" for a generic R-Car Gen3 compatible device. + + When compatible with the generic version nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + - reg: the register base and size for the device registers - interrupts: the interrupt for the device - clocks: Reference to the parent clock @@ -36,7 +45,7 @@ Device node example }; vin0: vin@0xe6ef0000 { - compatible = "renesas,vin-r8a7790"; + compatible = "renesas,vin-r8a7790", "renesas,rcar-gen2-vin"; clocks = <&mstp8_clks R8A7790_CLK_VIN0>; reg = <0 0xe6ef0000 0 0x1000>; interrupts = <0 188 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/media/renesas,drif.txt b/Documentation/devicetree/bindings/media/renesas,drif.txt new file mode 100644 index 000000000000..0d8974aa8b38 --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,drif.txt @@ -0,0 +1,177 @@ +Renesas R-Car Gen3 Digital Radio Interface controller (DRIF) +------------------------------------------------------------ + +R-Car Gen3 DRIF is a SPI like receive only slave device. A general +representation of DRIF interfacing with a master device is shown below. + ++---------------------+ +---------------------+ +| |-----SCK------->|CLK | +| Master |-----SS-------->|SYNC DRIFn (slave) | +| |-----SD0------->|D0 | +| |-----SD1------->|D1 | ++---------------------+ +---------------------+ + +As per datasheet, each DRIF channel (drifn) is made up of two internal +channels (drifn0 & drifn1). These two internal channels share the common +CLK & SYNC. Each internal channel has its own dedicated resources like +irq, dma channels, address space & clock. This internal split is not +visible to the external master device. + +The device tree model represents each internal channel as a separate node. +The internal channels sharing the CLK & SYNC are tied together by their +phandles using a property called "renesas,bonding". For the rest of +the documentation, unless explicitly stated, the word channel implies an +internal channel. + +When both internal channels are enabled they need to be managed together +as one (i.e.) they cannot operate alone as independent devices. Out of the +two, one of them needs to act as a primary device that accepts common +properties of both the internal channels. This channel is identified by a +property called "renesas,primary-bond". + +To summarize, + - When both the internal channels that are bonded together are enabled, + the zeroth channel is selected as primary-bond. This channels accepts + properties common to all the members of the bond. + - When only one of the bonded channels need to be enabled, the property + "renesas,bonding" or "renesas,primary-bond" will have no effect. That + enabled channel can act alone as any other independent device. + +Required properties of an internal channel: +------------------------------------------- +- compatible: "renesas,r8a7795-drif" if DRIF controller is a part of R8A7795 SoC. + "renesas,r8a7796-drif" if DRIF controller is a part of R8A7796 SoC. + "renesas,rcar-gen3-drif" for a generic R-Car Gen3 compatible device. + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + +- reg: offset and length of that channel. +- interrupts: associated with that channel. +- clocks: phandle and clock specifier of that channel. +- clock-names: clock input name string: "fck". +- dmas: phandles to the DMA channels. +- dma-names: names of the DMA channel: "rx". +- renesas,bonding: phandle to the other channel. + +Optional properties of an internal channel: +------------------------------------------- +- power-domains: phandle to the respective power domain. + +Required properties of an internal channel when: + - It is the only enabled channel of the bond (or) + - If it acts as primary among enabled bonds +-------------------------------------------------------- +- pinctrl-0: pin control group to be used for this channel. +- pinctrl-names: must be "default". +- renesas,primary-bond: empty property indicating the channel acts as primary + among the bonded channels. +- port: child port node corresponding to the data input, in accordance with + the video interface bindings defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The port + node must contain at least one endpoint. + +Optional endpoint property: +--------------------------- +- sync-active: Indicates sync signal polarity, 0/1 for low/high respectively. + This property maps to SYNCAC bit in the hardware manual. The + default is 1 (active high). + +Example: +-------- + +(1) Both internal channels enabled: +----------------------------------- + +When interfacing with a third party tuner device with two data pins as shown +below. + ++---------------------+ +---------------------+ +| |-----SCK------->|CLK | +| Master |-----SS-------->|SYNC DRIFn (slave) | +| |-----SD0------->|D0 | +| |-----SD1------->|D1 | ++---------------------+ +---------------------+ + + drif00: rif@e6f40000 { + compatible = "renesas,r8a7795-drif", + "renesas,rcar-gen3-drif"; + reg = <0 0xe6f40000 0 0x64>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 515>; + clock-names = "fck"; + dmas = <&dmac1 0x20>, <&dmac2 0x20>; + dma-names = "rx", "rx"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + renesas,bonding = <&drif01>; + renesas,primary-bond; + pinctrl-0 = <&drif0_pins>; + pinctrl-names = "default"; + port { + drif0_ep: endpoint { + remote-endpoint = <&tuner_ep>; + }; + }; + }; + + drif01: rif@e6f50000 { + compatible = "renesas,r8a7795-drif", + "renesas,rcar-gen3-drif"; + reg = <0 0xe6f50000 0 0x64>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 514>; + clock-names = "fck"; + dmas = <&dmac1 0x22>, <&dmac2 0x22>; + dma-names = "rx", "rx"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + renesas,bonding = <&drif00>; + }; + + +(2) Internal channel 1 alone is enabled: +---------------------------------------- + +When interfacing with a third party tuner device with one data pin as shown +below. + ++---------------------+ +---------------------+ +| |-----SCK------->|CLK | +| Master |-----SS-------->|SYNC DRIFn (slave) | +| | |D0 (unused) | +| |-----SD-------->|D1 | ++---------------------+ +---------------------+ + + drif00: rif@e6f40000 { + compatible = "renesas,r8a7795-drif", + "renesas,rcar-gen3-drif"; + reg = <0 0xe6f40000 0 0x64>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 515>; + clock-names = "fck"; + dmas = <&dmac1 0x20>, <&dmac2 0x20>; + dma-names = "rx", "rx"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + renesas,bonding = <&drif01>; + }; + + drif01: rif@e6f50000 { + compatible = "renesas,r8a7795-drif", + "renesas,rcar-gen3-drif"; + reg = <0 0xe6f50000 0 0x64>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 514>; + clock-names = "fck"; + dmas = <&dmac1 0x22>, <&dmac2 0x22>; + dma-names = "rx", "rx"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + renesas,bonding = <&drif00>; + pinctrl-0 = <&drif0_pins>; + pinctrl-names = "default"; + port { + drif0_ep: endpoint { + remote-endpoint = <&tuner_ep>; + sync-active = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/renesas,fcp.txt b/Documentation/devicetree/bindings/media/renesas,fcp.txt new file mode 100644 index 000000000000..3ec91803ba58 --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,fcp.txt @@ -0,0 +1,33 @@ +Renesas R-Car Frame Compression Processor (FCP) +----------------------------------------------- + +The FCP is a companion module of video processing modules in the Renesas R-Car +Gen3 SoCs. It provides data compression and decompression, data caching, and +conversion of AXI transactions in order to reduce the memory bandwidth. + +There are three types of FCP: FCP for Codec (FCPC), FCP for VSP (FCPV) and FCP +for FDP (FCPF). Their configuration and behaviour depend on the module they +are paired with. These DT bindings currently support the FCPV and FCPF. + + - compatible: Must be one or more of the following + + - "renesas,fcpv" for generic compatible 'FCP for VSP' + - "renesas,fcpf" for generic compatible 'FCP for FDP' + + - reg: the register base and size for the device registers + - clocks: Reference to the functional clock + +Optional properties: + - power-domains : power-domain property defined with a power domain specifier + to respective power domain. + + +Device node example +------------------- + + fcpvd1: fcp@fea2f000 { + compatible = "renesas,fcpv"; + reg = <0 0xfea2f000 0 0x200>; + clocks = <&cpg CPG_MOD 602>; + power-domains = <&sysc R8A7795_PD_A3VP>; + }; diff --git a/Documentation/devicetree/bindings/media/renesas,fdp1.txt b/Documentation/devicetree/bindings/media/renesas,fdp1.txt new file mode 100644 index 000000000000..8dd1007bb573 --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,fdp1.txt @@ -0,0 +1,37 @@ +Renesas R-Car Fine Display Processor (FDP1) +------------------------------------------- + +The FDP1 is a de-interlacing module which converts interlaced video to +progressive video. It is capable of performing pixel format conversion between +YCbCr/YUV formats and RGB formats. Only YCbCr/YUV formats are supported as +an input to the module. + +Required properties: + + - compatible: must be "renesas,fdp1" + - reg: the register base and size for the device registers + - interrupts : interrupt specifier for the FDP1 instance + - clocks: reference to the functional clock + +Optional properties: + + - power-domains: reference to the power domain that the FDP1 belongs to, if + any. + - renesas,fcp: a phandle referencing the FCP that handles memory accesses + for the FDP1. Not needed on Gen2, mandatory on Gen3. + +Please refer to the binding documentation for the clock and/or power domain +providers for more details. + + +Device node example +------------------- + + fdp1@fe940000 { + compatible = "renesas,fdp1"; + reg = <0 0xfe940000 0 0x2400>; + interrupts = <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 119>; + power-domains = <&sysc R8A7795_PD_A3VP>; + renesas,fcp = <&fcpf0>; + }; diff --git a/Documentation/devicetree/bindings/media/renesas,jpu.txt b/Documentation/devicetree/bindings/media/renesas,jpu.txt index 0cb94201bf92..d3436e5190f9 100644 --- a/Documentation/devicetree/bindings/media/renesas,jpu.txt +++ b/Documentation/devicetree/bindings/media/renesas,jpu.txt @@ -5,11 +5,12 @@ and decoding function conforming to the JPEG baseline process, so that the JPU can encode image data and decode JPEG data quickly. Required properties: - - compatible: should containg one of the following: - - "renesas,jpu-r8a7790" for R-Car H2 - - "renesas,jpu-r8a7791" for R-Car M2-W - - "renesas,jpu-r8a7792" for R-Car V2H - - "renesas,jpu-r8a7793" for R-Car M2-N +- compatible: "renesas,jpu-<soctype>", "renesas,rcar-gen2-jpu" as fallback. + Examples with soctypes are: + - "renesas,jpu-r8a7790" for R-Car H2 + - "renesas,jpu-r8a7791" for R-Car M2-W + - "renesas,jpu-r8a7792" for R-Car V2H + - "renesas,jpu-r8a7793" for R-Car M2-N - reg: Base address and length of the registers block for the JPU. - interrupts: JPU interrupt specifier. @@ -17,7 +18,7 @@ Required properties: Example: R8A7790 (R-Car H2) JPU node jpeg-codec@fe980000 { - compatible = "renesas,jpu-r8a7790"; + compatible = "renesas,jpu-r8a7790", "renesas,rcar-gen2-jpu"; reg = <0 0xfe980000 0 0x10300>; interrupts = <0 272 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp1_clks R8A7790_CLK_JPU>; diff --git a/Documentation/devicetree/bindings/media/renesas,vsp1.txt b/Documentation/devicetree/bindings/media/renesas,vsp1.txt index 87fe08abf36d..9b695bcbf219 100644 --- a/Documentation/devicetree/bindings/media/renesas,vsp1.txt +++ b/Documentation/devicetree/bindings/media/renesas,vsp1.txt @@ -1,30 +1,23 @@ -* Renesas VSP1 Video Processing Engine +* Renesas VSP Video Processing Engine -The VSP1 is a video processing engine that supports up-/down-scaling, alpha +The VSP is a video processing engine that supports up-/down-scaling, alpha blending, color space conversion and various other image processing features. It can be found in the Renesas R-Car second generation SoCs. Required properties: - - compatible: Must contain "renesas,vsp1" - - - reg: Base address and length of the registers block for the VSP1. - - interrupts: VSP1 interrupt specifier. - - clocks: A phandle + clock-specifier pair for the VSP1 functional clock. - - - renesas,#rpf: Number of Read Pixel Formatter (RPF) modules in the VSP1. - - renesas,#uds: Number of Up Down Scaler (UDS) modules in the VSP1. - - renesas,#wpf: Number of Write Pixel Formatter (WPF) modules in the VSP1. + - compatible: Must contain one of the following values + - "renesas,vsp1" for the R-Car Gen2 VSP1 + - "renesas,vsp2" for the R-Car Gen3 VSP2 + - reg: Base address and length of the registers block for the VSP. + - interrupts: VSP interrupt specifier. + - clocks: A phandle + clock-specifier pair for the VSP functional clock. Optional properties: - - renesas,has-lif: Boolean, indicates that the LCD Interface (LIF) module is - available. - - renesas,has-lut: Boolean, indicates that the Look Up Table (LUT) module is - available. - - renesas,has-sru: Boolean, indicates that the Super Resolution Unit (SRU) - module is available. + - renesas,fcp: A phandle referencing the FCP that handles memory accesses + for the VSP. Not needed on Gen2, mandatory on Gen3. Example: R8A7790 (R-Car H2) VSP1-S node @@ -34,10 +27,4 @@ Example: R8A7790 (R-Car H2) VSP1-S node reg = <0 0xfe928000 0 0x8000>; interrupts = <0 267 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp1_clks R8A7790_CLK_VSP1_S>; - - renesas,has-lut; - renesas,has-sru; - renesas,#rpf = <5>; - renesas,#uds = <3>; - renesas,#wpf = <4>; }; diff --git a/Documentation/devicetree/bindings/media/s5p-cec.txt b/Documentation/devicetree/bindings/media/s5p-cec.txt new file mode 100644 index 000000000000..1b1a10ba48ce --- /dev/null +++ b/Documentation/devicetree/bindings/media/s5p-cec.txt @@ -0,0 +1,37 @@ +* Samsung HDMI CEC driver + +The HDMI CEC module is present is Samsung SoCs and its purpose is to +handle communication between HDMI connected devices over the CEC bus. + +Required properties: + - compatible : value should be following + "samsung,s5p-cec" + + - reg : Physical base address of the IP registers and length of memory + mapped region. + + - interrupts : HDMI CEC interrupt number to the CPU. + - clocks : from common clock binding: handle to HDMI CEC clock. + - clock-names : from common clock binding: must contain "hdmicec", + corresponding to entry in the clocks property. + - samsung,syscon-phandle - phandle to the PMU system controller + - hdmi-phandle - phandle to the HDMI controller, see also cec.txt. + +Optional: + - needs-hpd : if present the CEC support is only available when the HPD + is high. See cec.txt for more details. + +Example: + +hdmicec: cec@100B0000 { + compatible = "samsung,s5p-cec"; + reg = <0x100B0000 0x200>; + interrupts = <0 114 0>; + clocks = <&clock CLK_HDMI_CEC>; + clock-names = "hdmicec"; + samsung,syscon-phandle = <&pmu_system_controller>; + hdmi-phandle = <&hdmi>; + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_cec>; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/media/s5p-mfc.txt b/Documentation/devicetree/bindings/media/s5p-mfc.txt index 2d5787eac91a..d3404b5d4d17 100644 --- a/Documentation/devicetree/bindings/media/s5p-mfc.txt +++ b/Documentation/devicetree/bindings/media/s5p-mfc.txt @@ -12,6 +12,7 @@ Required properties: (b) "samsung,mfc-v6" for MFC v6 present in Exynos5 SoCs (c) "samsung,mfc-v7" for MFC v7 present in Exynos5420 SoC (d) "samsung,mfc-v8" for MFC v8 present in Exynos5800 SoC + (e) "samsung,exynos5433-mfc" for MFC v8 present in Exynos5433 SoC - reg : Physical base address of the IP registers and length of memory mapped region. @@ -21,15 +22,18 @@ Required properties: - clock-names : from common clock binding: must contain "mfc", corresponding to entry in the clocks property. - - samsung,mfc-r : Base address of the first memory bank used by MFC - for DMA contiguous memory allocation and its size. - - - samsung,mfc-l : Base address of the second memory bank used by MFC - for DMA contiguous memory allocation and its size. - Optional properties: - power-domains : power-domain property defined with a phandle to respective power domain. + - memory-region : from reserved memory binding: phandles to two reserved + memory regions, first is for "left" mfc memory bus interfaces, + second if for the "right" mfc memory bus, used when no SYSMMU + support is available; used only by MFC v5 present in Exynos4 SoCs + +Obsolete properties: + - samsung,mfc-r, samsung,mfc-l : support removed, please use memory-region + property instead + Example: SoC specific DT entry: @@ -43,9 +47,29 @@ mfc: codec@13400000 { clock-names = "mfc"; }; +Reserved memory specific DT entry for given board (see reserved memory binding +for more information): + +reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + mfc_left: region@51000000 { + compatible = "shared-dma-pool"; + no-map; + reg = <0x51000000 0x800000>; + }; + + mfc_right: region@43000000 { + compatible = "shared-dma-pool"; + no-map; + reg = <0x43000000 0x800000>; + }; +}; + Board specific DT entry: codec@13400000 { - samsung,mfc-r = <0x43000000 0x800000>; - samsung,mfc-l = <0x51000000 0x800000>; + memory-region = <&mfc_left>, <&mfc_right>; }; diff --git a/Documentation/devicetree/bindings/media/st,st-delta.txt b/Documentation/devicetree/bindings/media/st,st-delta.txt new file mode 100644 index 000000000000..a538ab30a617 --- /dev/null +++ b/Documentation/devicetree/bindings/media/st,st-delta.txt @@ -0,0 +1,17 @@ +* STMicroelectronics DELTA multi-format video decoder + +Required properties: +- compatible: should be "st,st-delta". +- clocks: from common clock binding: handle hardware IP needed clocks, the + number of clocks may depend on the SoC type. + See ../clock/clock-bindings.txt for details. +- clock-names: names of the clocks listed in clocks property in the same order. + +Example: + delta0 { + compatible = "st,st-delta"; + clock-names = "delta", "delta-st231", "delta-flash-promip"; + clocks = <&clk_s_c0_flexgen CLK_VID_DMU>, + <&clk_s_c0_flexgen CLK_ST231_DMU>, + <&clk_s_c0_flexgen CLK_FLASH_PROMIP>; + }; diff --git a/Documentation/devicetree/bindings/media/st,st-hva.txt b/Documentation/devicetree/bindings/media/st,st-hva.txt new file mode 100644 index 000000000000..0d76174a1f7e --- /dev/null +++ b/Documentation/devicetree/bindings/media/st,st-hva.txt @@ -0,0 +1,24 @@ +st-hva: multi-format video encoder for STMicroelectronics SoC. + +Required properties: +- compatible: should be "st,st-hva". +- reg: HVA physical address location and length, esram address location and + length. +- reg-names: names of the registers listed in registers property in the same + order. +- interrupts: HVA interrupt number. +- clocks: from common clock binding: handle hardware IP needed clocks, the + number of clocks may depend on the SoC type. + See ../clock/clock-bindings.txt for details. +- clock-names: names of the clocks listed in clocks property in the same order. + +Example: + hva@8c85000{ + compatible = "st,st-hva"; + reg = <0x8c85000 0x400>, <0x6000000 0x40000>; + reg-names = "hva_registers", "hva_esram"; + interrupts = <GIC_SPI 58 IRQ_TYPE_NONE>, + <GIC_SPI 59 IRQ_TYPE_NONE>; + clock-names = "clk_hva"; + clocks = <&clk_s_c0_flexgen CLK_HVA>; + }; diff --git a/Documentation/devicetree/bindings/media/st,stm32-cec.txt b/Documentation/devicetree/bindings/media/st,stm32-cec.txt new file mode 100644 index 000000000000..6be2381c180d --- /dev/null +++ b/Documentation/devicetree/bindings/media/st,stm32-cec.txt @@ -0,0 +1,19 @@ +STMicroelectronics STM32 CEC driver + +Required properties: + - compatible : value should be "st,stm32-cec" + - reg : Physical base address of the IP registers and length of memory + mapped region. + - clocks : from common clock binding: handle to CEC clocks + - clock-names : from common clock binding: must be "cec" and "hdmi-cec". + - interrupts : CEC interrupt number to the CPU. + +Example for stm32f746: + +cec: cec@40006c00 { + compatible = "st,stm32-cec"; + reg = <0x40006C00 0x400>; + interrupts = <94>; + clocks = <&rcc 0 STM32F7_APB1_CLOCK(CEC)>, <&rcc 1 CLK_HDMI_CEC>; + clock-names = "cec", "hdmi-cec"; +}; diff --git a/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt b/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt new file mode 100644 index 000000000000..249790a93017 --- /dev/null +++ b/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt @@ -0,0 +1,45 @@ +STMicroelectronics STM32 Digital Camera Memory Interface (DCMI) + +Required properties: +- compatible: "st,stm32-dcmi" +- reg: physical base address and length of the registers set for the device +- interrupts: should contain IRQ line for the DCMI +- resets: reference to a reset controller, + see Documentation/devicetree/bindings/reset/st,stm32-rcc.txt +- clocks: list of clock specifiers, corresponding to entries in + the clock-names property +- clock-names: must contain "mclk", which is the DCMI peripherial clock +- pinctrl: the pincontrol settings to configure muxing properly + for pins that connect to DCMI device. + See Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt. +- dmas: phandle to DMA controller node, + see Documentation/devicetree/bindings/dma/stm32-dma.txt +- dma-names: must contain "tx", which is the transmit channel from DCMI to DMA + +DCMI supports a single port node with parallel bus. It should contain one +'port' child node with child 'endpoint' node. Please refer to the bindings +defined in Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + dcmi: dcmi@50050000 { + compatible = "st,stm32-dcmi"; + reg = <0x50050000 0x400>; + interrupts = <78>; + resets = <&rcc STM32F4_AHB2_RESET(DCMI)>; + clocks = <&rcc 0 STM32F4_AHB2_CLOCK(DCMI)>; + clock-names = "mclk"; + pinctrl-names = "default"; + pinctrl-0 = <&dcmi_pins>; + dmas = <&dma2 1 1 0x414 0x3>; + dma-names = "tx"; + port { + dcmi_0: endpoint { + remote-endpoint = <...>; + bus-width = <8>; + hsync-active = <0>; + vsync-active = <0>; + pclk-sample = <1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/stih-cec.txt b/Documentation/devicetree/bindings/media/stih-cec.txt new file mode 100644 index 000000000000..8be2a040c6c6 --- /dev/null +++ b/Documentation/devicetree/bindings/media/stih-cec.txt @@ -0,0 +1,27 @@ +STMicroelectronics STIH4xx HDMI CEC driver + +Required properties: + - compatible : value should be "st,stih-cec" + - reg : Physical base address of the IP registers and length of memory + mapped region. + - clocks : from common clock binding: handle to HDMI CEC clock + - interrupts : HDMI CEC interrupt number to the CPU. + - pinctrl-names: Contains only one value - "default" + - pinctrl-0: Specifies the pin control groups used for CEC hardware. + - resets: Reference to a reset controller + - hdmi-phandle: Phandle to the HDMI controller, see also cec.txt. + +Example for STIH407: + +sti-cec@094a087c { + compatible = "st,stih-cec"; + reg = <0x94a087c 0x64>; + clocks = <&clk_sysin>; + clock-names = "cec-clk"; + interrupts = <GIC_SPI 140 IRQ_TYPE_NONE>; + interrupt-names = "cec-irq"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_cec0_default>; + resets = <&softreset STIH407_LPM_SOFTRESET>; + hdmi-phandle = <&hdmi>; +}; diff --git a/Documentation/devicetree/bindings/media/sunxi-ir.txt b/Documentation/devicetree/bindings/media/sunxi-ir.txt index 1811a067c72c..302a0b183cb8 100644 --- a/Documentation/devicetree/bindings/media/sunxi-ir.txt +++ b/Documentation/devicetree/bindings/media/sunxi-ir.txt @@ -9,7 +9,7 @@ Required properties: - reg : should contain IO map address for IR. Optional properties: -- linux,rc-map-name : Remote control map name. +- linux,rc-map-name: see rc.txt file in the same directory. - resets : phandle + reset specifier pair Example: diff --git a/Documentation/devicetree/bindings/media/ti,da850-vpif.txt b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt new file mode 100644 index 000000000000..df7182a63e59 --- /dev/null +++ b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt @@ -0,0 +1,107 @@ +Texas Instruments VPIF +---------------------- + +The TI Video Port InterFace (VPIF) is the primary component for video +capture and display on the DA850/AM18x family of TI DaVinci/Sitara +SoCs. + +TI Document reference: SPRUH82C, Chapter 35 +http://www.ti.com/lit/pdf/spruh82 + +Required properties: +- compatible: must be "ti,da850-vpif" +- reg: physical base address and length of the registers set for the device; +- interrupts: should contain IRQ line for the VPIF + +Video Capture: + +VPIF has a 16-bit parallel bus input, supporting 2 8-bit channels or a +single 16-bit channel. It should contain one or two port child nodes +with child 'endpoint' node. If there are two ports then port@0 must +describe the input and port@1 output channels. Please refer to the +bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example using 2 8-bit input channels, one of which is connected to an +I2C-connected TVP5147 decoder: + + vpif: vpif@217000 { + compatible = "ti,da850-vpif"; + reg = <0x217000 0x1000>; + interrupts = <92>; + + port@0 { + vpif_input_ch0: endpoint@0 { + reg = <0>; + bus-width = <8>; + remote-endpoint = <&composite_in>; + }; + + vpif_input_ch1: endpoint@1 { + reg = <1>; + bus-width = <8>; + data-shift = <8>; + }; + }; + + port@1 { + vpif_output_ch0: endpoint { + bus-width = <8>; + remote-endpoint = <&composite_out>; + }; + }; + }; + +[ ... ] + +&i2c0 { + + tvp5147@5d { + compatible = "ti,tvp5147"; + reg = <0x5d>; + status = "okay"; + + port { + composite_in: endpoint { + hsync-active = <1>; + vsync-active = <1>; + pclk-sample = <0>; + + /* VPIF channel 0 (lower 8-bits) */ + remote-endpoint = <&vpif_input_ch0>; + bus-width = <8>; + }; + }; + }; + + adv7343@2a { + compatible = "adi,adv7343"; + reg = <0x2a>; + + port { + composite_out: endpoint { + adi,dac-enable = <1 1 1>; + adi,sd-dac-enable = <1>; + + remote-endpoint = <&vpif_output_ch0>; + bus-width = <8>; + }; + }; + }; +}; + + +Alternatively, an example when the bus is configured as a single +16-bit input (e.g. for raw-capture mode): + + vpif: vpif@217000 { + compatible = "ti,da850-vpif"; + reg = <0x217000 0x1000>; + interrupts = <92>; + + port { + vpif_ch0: endpoint { + bus-width = <16>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/ti-cal.txt b/Documentation/devicetree/bindings/media/ti-cal.txt new file mode 100644 index 000000000000..ae9b52f37576 --- /dev/null +++ b/Documentation/devicetree/bindings/media/ti-cal.txt @@ -0,0 +1,72 @@ +Texas Instruments DRA72x CAMERA ADAPTATION LAYER (CAL) +------------------------------------------------------ + +The Camera Adaptation Layer (CAL) is a key component for image capture +applications. The capture module provides the system interface and the +processing capability to connect CSI2 image-sensor modules to the +DRA72x device. + +Required properties: +- compatible: must be "ti,dra72-cal" +- reg: CAL Top level, Receiver Core #0, Receiver Core #1 and Camera RX + control address space +- reg-names: cal_top, cal_rx_core0, cal_rx_core1, and camerrx_control + registers +- interrupts: should contain IRQ line for the CAL; + +CAL supports 2 camera port nodes on MIPI bus. Each CSI2 camera port nodes +should contain a 'port' child node with child 'endpoint' node. Please +refer to the bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + cal: cal@4845b000 { + compatible = "ti,dra72-cal"; + ti,hwmods = "cal"; + reg = <0x4845B000 0x400>, + <0x4845B800 0x40>, + <0x4845B900 0x40>, + <0x4A002e94 0x4>; + reg-names = "cal_top", + "cal_rx_core0", + "cal_rx_core1", + "camerrx_control"; + interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + csi2_0: port@0 { + reg = <0>; + endpoint { + slave-mode; + remote-endpoint = <&ar0330_1>; + }; + }; + csi2_1: port@1 { + reg = <1>; + }; + }; + }; + + i2c5: i2c@4807c000 { + ar0330@10 { + compatible = "ti,ar0330"; + reg = <0x10>; + + port { + #address-cells = <1>; + #size-cells = <0>; + + ar0330_1: endpoint { + reg = <0>; + clock-lanes = <1>; + data-lanes = <0 2 3 4>; + remote-endpoint = <&csi2_0>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/video-interfaces.txt b/Documentation/devicetree/bindings/media/video-interfaces.txt index 9cd2a369125d..852041a7480c 100644 --- a/Documentation/devicetree/bindings/media/video-interfaces.txt +++ b/Documentation/devicetree/bindings/media/video-interfaces.txt @@ -76,6 +76,11 @@ Optional endpoint properties mode horizontal and vertical synchronization signals are provided to the slave device (data source) by the master device (data sink). In the master mode the data source device is also the source of the synchronization signals. +- bus-type: data bus type. Possible values are: + 0 - autodetect based on other properties (MIPI CSI-2 D-PHY, parallel or Bt656) + 1 - MIPI CSI-2 C-PHY + 2 - MIPI CSI1 + 3 - CCP2 - bus-width: number of data lines actively used, valid for the parallel busses. - data-shift: on the parallel data busses, if bus-width is used to specify the number of data lines, data-shift can be used to specify which data lines are @@ -112,7 +117,8 @@ Optional endpoint properties should be the combined length of data-lanes and clock-lanes properties. If the lane-polarities property is omitted, the value must be interpreted as 0 (normal). This property is valid for serial busses only. - +- strobe: Whether the clock signal is used as clock (0) or strobe (1). Used + with CCP2, for instance. Example ------- diff --git a/Documentation/devicetree/bindings/media/video-mux.txt b/Documentation/devicetree/bindings/media/video-mux.txt new file mode 100644 index 000000000000..63b9dc913e45 --- /dev/null +++ b/Documentation/devicetree/bindings/media/video-mux.txt @@ -0,0 +1,60 @@ +Video Multiplexer +================= + +Video multiplexers allow to select between multiple input ports. Video received +on the active input port is passed through to the output port. Muxes described +by this binding are controlled by a multiplexer controller that is described by +the bindings in Documentation/devicetree/bindings/mux/mux-controller.txt + +Required properties: +- compatible : should be "video-mux" +- mux-controls : mux controller node to use for operating the mux +- #address-cells: should be <1> +- #size-cells: should be <0> +- port@*: at least three port nodes containing endpoints connecting to the + source and sink devices according to of_graph bindings. The last port is + the output port, all others are inputs. + +Optionally, #address-cells, #size-cells, and port nodes can be grouped under a +ports node as described in Documentation/devicetree/bindings/graph.txt. + +Example: + + mux: mux-controller { + compatible = "gpio-mux"; + #mux-control-cells = <0>; + + mux-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; + }; + + video-mux { + compatible = "video-mux"; + mux-controls = <&mux>; + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + mux_in0: endpoint { + remote-endpoint = <&video_source0_out>; + }; + }; + + port@1 { + reg = <1>; + + mux_in1: endpoint { + remote-endpoint = <&video_source1_out>; + }; + }; + + port@2 { + reg = <2>; + + mux_out: endpoint { + remote-endpoint = <&capture_interface_in>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/xilinx/video.txt b/Documentation/devicetree/bindings/media/xilinx/video.txt index cbd46fa0988f..68ac210e688e 100644 --- a/Documentation/devicetree/bindings/media/xilinx/video.txt +++ b/Documentation/devicetree/bindings/media/xilinx/video.txt @@ -20,7 +20,7 @@ The following properties are common to all Xilinx video IP cores. - xlnx,video-format: This property represents a video format transmitted on an AXI bus between video IP cores, using its VF code as defined in "AXI4-Stream Video IP and System Design Guide" [UG934]. How the format relates to the IP - core is decribed in the IP core bindings documentation. + core is described in the IP core bindings documentation. - xlnx,video-width: This property qualifies the video format with the sample width expressed as a number of bits per pixel component. All components must |