diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mfd')
38 files changed, 1679 insertions, 66 deletions
diff --git a/Documentation/devicetree/bindings/mfd/ac100.txt b/Documentation/devicetree/bindings/mfd/ac100.txt new file mode 100644 index 000000000000..b8ef00667599 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/ac100.txt @@ -0,0 +1,54 @@ +X-Powers AC100 Codec/RTC IC Device Tree bindings + +AC100 is a audio codec and RTC subsystem combo IC. The 2 parts are +separated, including power supplies and interrupt lines, but share +a common register address space and host interface. + +Required properties: +- compatible: "x-powers,ac100" +- reg: The I2C slave address or RSB hardware address for the chip +- sub-nodes: + - codec + - compatible: "x-powers,ac100-codec" + - interrupt-parent: The parent interrupt controller + - interrupts: SoC NMI / GPIO interrupt connected to the + IRQ_AUDIO pin + - #clock-cells: Shall be 0 + - clock-output-names: "4M_adda" + + - see clock/clock-bindings.txt for common clock bindings + + - rtc + - compatible: "x-powers,ac100-rtc" + - interrupt-parent: The parent interrupt controller + - interrupts: SoC NMI / GPIO interrupt connected to the + IRQ_RTC pin + - clocks: A phandle to the codec's "4M_adda" clock + - #clock-cells: Shall be 1 + - clock-output-names: "cko1_rtc", "cko2_rtc", "cko3_rtc" + + - see clock/clock-bindings.txt for common clock bindings + +Example: + +ac100: codec@e89 { + compatible = "x-powers,ac100"; + reg = <0xe89>; + + ac100_codec: codec { + compatible = "x-powers,ac100-codec"; + interrupt-parent = <&r_pio>; + interrupts = <0 9 IRQ_TYPE_LEVEL_LOW>; /* PL9 */ + #clock-cells = <0>; + clock-output-names = "4M_adda"; + }; + + ac100_rtc: rtc { + compatible = "x-powers,ac100-rtc"; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + clocks = <&ac100_codec>; + #clock-cells = <1>; + clock-output-names = "cko1_rtc", "cko2_rtc", "cko3_rtc"; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/act8945a.txt b/Documentation/devicetree/bindings/mfd/act8945a.txt new file mode 100644 index 000000000000..462819ac3da8 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/act8945a.txt @@ -0,0 +1,84 @@ +Device-Tree bindings for Active-semi ACT8945A MFD driver + +Required properties: + - compatible: "active-semi,act8945a". + - reg: the I2C slave address for the ACT8945A chip + +The chip exposes two subdevices: + - a regulators: see ../regulator/act8945a-regulator.txt + - a charger: see ../power/act8945a-charger.txt + +Example: + pmic@5b { + compatible = "active-semi,act8945a"; + reg = <0x5b>; + status = "okay"; + + active-semi,vsel-high; + + regulators { + vdd_1v35_reg: REG_DCDC1 { + regulator-name = "VDD_1V35"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + vdd_1v2_reg: REG_DCDC2 { + regulator-name = "VDD_1V2"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + }; + + vdd_3v3_reg: REG_DCDC3 { + regulator-name = "VDD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_fuse_reg: REG_LDO1 { + regulator-name = "VDD_FUSE"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + vdd_3v3_lp_reg: REG_LDO2 { + regulator-name = "VDD_3V3_LP"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_led_reg: REG_LDO3 { + regulator-name = "VDD_LED"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_sdhc_1v8_reg: REG_LDO4 { + regulator-name = "VDD_SDHC_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + }; + + charger { + compatible = "active-semi,act8945a-charger"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_charger_chglev &pinctrl_charger_lbo &pinctrl_charger_irq>; + interrupt-parent = <&pioA>; + interrupts = <45 GPIO_ACTIVE_LOW>; + + active-semi,chglev-gpios = <&pioA 12 GPIO_ACTIVE_HIGH>; + active-semi,lbo-gpios = <&pioA 72 GPIO_ACTIVE_LOW>; + active-semi,input-voltage-threshold-microvolt = <6600>; + active-semi,precondition-timeout = <40>; + active-semi,total-timeout = <3>; + status = "okay"; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/altera-a10sr.txt b/Documentation/devicetree/bindings/mfd/altera-a10sr.txt new file mode 100644 index 000000000000..c8a736554b4b --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/altera-a10sr.txt @@ -0,0 +1,57 @@ +* Altera Arria10 Development Kit System Resource Chip + +Required parent device properties: +- compatible : "altr,a10sr" +- spi-max-frequency : Maximum SPI frequency. +- reg : The SPI Chip Select address for the Arria10 + System Resource chip +- interrupt-parent : The parent interrupt controller. +- interrupts : The interrupt line the device is connected to. +- interrupt-controller : Marks the device node as an interrupt controller. +- #interrupt-cells : The number of cells to describe an IRQ, should be 2. + The first cell is the IRQ number. + The second cell is the flags, encoded as trigger + masks from ../interrupt-controller/interrupts.txt. + +The A10SR consists of these sub-devices: + +Device Description +------ ---------- +a10sr_gpio GPIO Controller +a10sr_rst Reset Controller + +Arria10 GPIO +Required Properties: +- compatible : Should be "altr,a10sr-gpio" +- gpio-controller : Marks the device node as a GPIO Controller. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify flags. + See ../gpio/gpio.txt for more information. + +Arria10 Peripheral PHY Reset +Required Properties: +- compatible : Should be "altr,a10sr-reset" +- #reset-cells : Should be one. + +Example: + + resource-manager@0 { + compatible = "altr,a10sr"; + reg = <0>; + spi-max-frequency = <100000>; + interrupt-parent = <&portb>; + interrupts = <5 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + + a10sr_gpio: gpio-controller { + compatible = "altr,a10sr-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + + a10sr_rst: reset-controller { + compatible = "altr,a10sr-reset"; + #reset-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/arizona.txt b/Documentation/devicetree/bindings/mfd/arizona.txt index 9b30011ecabe..b37bdde5cfda 100644 --- a/Documentation/devicetree/bindings/mfd/arizona.txt +++ b/Documentation/devicetree/bindings/mfd/arizona.txt @@ -1,6 +1,6 @@ Cirrus Logic/Wolfson Microelectronics Arizona class audio SoCs -These devices are audio SoCs with extensive digital capabilites and a range +These devices are audio SoCs with extensive digital capabilities and a range of analogue I/O. Required properties: @@ -30,7 +30,8 @@ Required properties: - gpio-controller : Indicates this device is a GPIO controller. - #gpio-cells : Must be 2. The first cell is the pin number and the - second cell is used to specify optional parameters (currently unused). + second cell is used to specify optional parameters, see ../gpio/gpio.txt + for details. - AVDD-supply, DBVDD1-supply, CPVDD-supply : Power supplies for the device, as covered in Documentation/devicetree/bindings/regulator/regulator.txt @@ -85,6 +86,24 @@ Optional properties: present, the number of values should be less than or equal to the number of inputs, unspecified inputs will use the chip default. + - wlf,max-channels-clocked : The maximum number of channels to be clocked on + each AIF, useful for I2S systems with multiple data lines being mastered. + Specify one cell for each AIF to be configured, specify zero for AIFs that + should be handled normally. + If present, number of cells must be less than or equal to the number of + AIFs. If less than the number of AIFs, for cells that have not been + specified the corresponding AIFs will be treated as default setting. + + - wlf,spk-fmt : PDM speaker data format, must contain 2 cells (OUT5 and OUT6). + See the datasheet for values. + The second cell is ignored for codecs that do not have OUT6 (wm5102, wm8997, + wm8998, wm1814) + + - wlf,spk-mute : PDM speaker mute setting, must contain 2 cells (OUT5 and OUT6). + See the datasheet for values. + The second cell is ignored for codecs that do not have OUT6 (wm5102, wm8997, + wm8998, wm1814) + - DCVDD-supply, MICVDD-supply : Power supplies, only need to be specified if they are being externally supplied. As covered in Documentation/devicetree/bindings/regulator/regulator.txt diff --git a/Documentation/devicetree/bindings/mfd/as3722.txt b/Documentation/devicetree/bindings/mfd/as3722.txt index 4f64b2a73169..0b2a6099aa20 100644 --- a/Documentation/devicetree/bindings/mfd/as3722.txt +++ b/Documentation/devicetree/bindings/mfd/as3722.txt @@ -122,8 +122,7 @@ Following are properties of regulator subnode. Power-off: ========= -AS3722 supports the system power off by turning off all its rail. This -is provided through pm_power_off. +AS3722 supports the system power off by turning off all its rails. The device node should have the following properties to enable this functionality ams,system-power-controller: Boolean, to enable the power off functionality diff --git a/Documentation/devicetree/bindings/mfd/aspeed-gfx.txt b/Documentation/devicetree/bindings/mfd/aspeed-gfx.txt new file mode 100644 index 000000000000..aea5370efd97 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/aspeed-gfx.txt @@ -0,0 +1,17 @@ +* Device tree bindings for Aspeed SoC Display Controller (GFX) + +The Aspeed SoC Display Controller primarily does as its name suggests, but also +participates in pinmux requests on the g5 SoCs. It is therefore considered a +syscon device. + +Required properties: +- compatible: "aspeed,ast2500-gfx", "syscon" +- reg: contains offset/length value of the GFX memory + region. + +Example: + +gfx: display@1e6e6000 { + compatible = "aspeed,ast2500-gfx", "syscon"; + reg = <0x1e6e6000 0x1000>; +}; diff --git a/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt b/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt new file mode 100644 index 000000000000..514d82ced95b --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt @@ -0,0 +1,137 @@ +====================================================================== +Device tree bindings for the Aspeed Low Pin Count (LPC) Bus Controller +====================================================================== + +The LPC bus is a means to bridge a host CPU to a number of low-bandwidth +peripheral devices, replacing the use of the ISA bus in the age of PCI[0]. The +primary use case of the Aspeed LPC controller is as a slave on the bus +(typically in a Baseboard Management Controller SoC), but under certain +conditions it can also take the role of bus master. + +The LPC controller is represented as a multi-function device to account for the +mix of functionality it provides. The principle split is between the register +layout at the start of the I/O space which is, to quote the Aspeed datasheet, +"basically compatible with the [LPC registers from the] popular BMC controller +H8S/2168[1]", and everything else, where everything else is an eclectic +collection of functions with a esoteric register layout. "Everything else", +here labeled the "host" portion of the controller, includes, but is not limited +to: + +* An IPMI Block Transfer[2] Controller + +* An LPC Host Controller: Manages LPC functions such as host vs slave mode, the + physical properties of some LPC pins, configuration of serial IRQs, and + APB-to-LPC bridging amonst other functions. + +* An LPC Host Interface Controller: Manages functions exposed to the host such + as LPC firmware hub cycles, configuration of the LPC-to-AHB mapping, UART + management and bus snoop configuration. + +* A set of SuperIO[3] scratch registers: Enables implementation of e.g. custom + hardware management protocols for handover between the host and baseboard + management controller. + +Additionally the state of the LPC controller influences the pinmux +configuration, therefore the host portion of the controller is exposed as a +syscon as a means to arbitrate access. + +[0] http://www.intel.com/design/chipsets/industry/25128901.pdf +[1] https://www.renesas.com/en-sg/doc/products/mpumcu/001/rej09b0078_h8s2168.pdf?key=7c88837454702128622bee53acbda8f4 +[2] http://www.intel.com/content/dam/www/public/us/en/documents/product-briefs/ipmi-second-gen-interface-spec-v2-rev1-1.pdf +[3] https://en.wikipedia.org/wiki/Super_I/O + +Required properties +=================== + +- compatible: One of: + "aspeed,ast2400-lpc", "simple-mfd" + "aspeed,ast2500-lpc", "simple-mfd" + +- reg: contains the physical address and length values of the Aspeed + LPC memory region. + +- #address-cells: <1> +- #size-cells: <1> +- ranges: Maps 0 to the physical address and length of the LPC memory + region + +Required LPC Child nodes +======================== + +BMC Node +-------- + +- compatible: One of: + "aspeed,ast2400-lpc-bmc" + "aspeed,ast2500-lpc-bmc" + +- reg: contains the physical address and length values of the + H8S/2168-compatible LPC controller memory region + +Host Node +--------- + +- compatible: One of: + "aspeed,ast2400-lpc-host", "simple-mfd", "syscon" + "aspeed,ast2500-lpc-host", "simple-mfd", "syscon" + +- reg: contains the address and length values of the host-related + register space for the Aspeed LPC controller + +- #address-cells: <1> +- #size-cells: <1> +- ranges: Maps 0 to the address and length of the host-related LPC memory + region + +Example: + +lpc: lpc@1e789000 { + compatible = "aspeed,ast2500-lpc", "simple-mfd"; + reg = <0x1e789000 0x1000>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x1e789000 0x1000>; + + lpc_bmc: lpc-bmc@0 { + compatible = "aspeed,ast2500-lpc-bmc"; + reg = <0x0 0x80>; + }; + + lpc_host: lpc-host@80 { + compatible = "aspeed,ast2500-lpc-host", "simple-mfd", "syscon"; + reg = <0x80 0x1e0>; + reg-io-width = <4>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x80 0x1e0>; + }; +}; + +Host Node Children +================== + +LPC Host Controller +------------------- + +The Aspeed LPC Host Controller configures the Low Pin Count (LPC) bus behaviour +between the host and the baseboard management controller. The registers exist +in the "host" portion of the Aspeed LPC controller, which must be the parent of +the LPC host controller node. + +Required properties: + +- compatible: One of: + "aspeed,ast2400-lhc"; + "aspeed,ast2500-lhc"; + +- reg: contains offset/length values of the LHC memory regions. In the + AST2400 and AST2500 there are two regions. + +Example: + +lhc: lhc@20 { + compatible = "aspeed,ast2500-lhc"; + reg = <0x20 0x24 0x48 0x8>; +}; diff --git a/Documentation/devicetree/bindings/mfd/aspeed-scu.txt b/Documentation/devicetree/bindings/mfd/aspeed-scu.txt new file mode 100644 index 000000000000..4fc5b83726d6 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/aspeed-scu.txt @@ -0,0 +1,18 @@ +The Aspeed System Control Unit manages the global behaviour of the SoC, +configuring elements such as clocks, pinmux, and reset. + +Required properties: +- compatible: One of: + "aspeed,ast2400-scu", "syscon", "simple-mfd" + "aspeed,g4-scu", "syscon", "simple-mfd" + "aspeed,ast2500-scu", "syscon", "simple-mfd" + "aspeed,g5-scu", "syscon", "simple-mfd" + +- reg: contains the offset and length of the SCU memory region + +Example: + +syscon: syscon@1e6e2000 { + compatible = "aspeed,ast2400-scu", "syscon", "simple-mfd"; + reg = <0x1e6e2000 0x1a8>; +}; diff --git a/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt b/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt index 670831b29565..eec40be7f79a 100644 --- a/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt +++ b/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt @@ -15,7 +15,7 @@ Required properties: The HLCDC IP exposes two subdevices: - a PWM chip: see ../pwm/atmel-hlcdc-pwm.txt - - a Display Controller: see ../display/atmel-hlcdc-dc.txt + - a Display Controller: see ../display/atmel/hlcdc-dc.txt Example: diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt index a474359dd206..aca09af66514 100644 --- a/Documentation/devicetree/bindings/mfd/axp20x.txt +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt @@ -5,11 +5,21 @@ axp152 (X-Powers) axp202 (X-Powers) axp209 (X-Powers) axp221 (X-Powers) +axp223 (X-Powers) +axp803 (X-Powers) +axp809 (X-Powers) Required properties: -- compatible: "x-powers,axp152", "x-powers,axp202", "x-powers,axp209", - "x-powers,axp221" -- reg: The I2C slave address for the AXP chip +- compatible: should be one of: + * "x-powers,axp152" + * "x-powers,axp202" + * "x-powers,axp209" + * "x-powers,axp221" + * "x-powers,axp223" + * "x-powers,axp803" + * "x-powers,axp806" + * "x-powers,axp809" +- reg: The I2C slave address or RSB hardware address for the AXP chip - interrupt-parent: The parent interrupt controller - interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin - interrupt-controller: The PMIC has its own internal IRQs @@ -17,7 +27,17 @@ Required properties: Optional properties: - x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz - (range: 750-1875). Default: 1.5MHz + AXP152/20X: range: 750-1875, Default: 1.5 MHz + AXP22X/80X: range: 1800-4050, Default: 3 MHz + +- x-powers,drive-vbus-en: axp221 / axp223 only boolean, set this when the + N_VBUSEN pin is used as an output pin to control an external + regulator to drive the OTG VBus, rather then as an input pin + which signals whether the board is driving OTG VBus or not. + +- x-powers,master-mode: Boolean (axp806 only). Set this when the PMIC is + wired for master mode. The default is slave mode. + - <input>-supply: a phandle to the regulator supply node. May be omitted if inputs are unregulated, such as using the IPSOUT output from the PMIC. @@ -38,7 +58,6 @@ Optional properties for DCDC regulators: probably makes sense for HiFi audio related applications that aren't battery constrained. - AXP202/AXP209 regulators, type, and corresponding input supply names: Regulator Type Supply Name Notes @@ -51,7 +70,7 @@ LDO3 : LDO : ldo3in-supply LDO4 : LDO : ldo24in-supply : shared supply LDO5 : LDO : ldo5in-supply -AXP221 regulators, type, and corresponding input supply names: +AXP221/AXP223 regulators, type, and corresponding input supply names: Regulator Type Supply Name Notes --------- ---- ----------- ----- @@ -75,6 +94,82 @@ ELDO3 : LDO : eldoin-supply : shared supply LDO_IO0 : LDO : ips-supply : GPIO 0 LDO_IO1 : LDO : ips-supply : GPIO 1 RTC_LDO : LDO : ips-supply : always on +DRIVEVBUS : Enable output : drivevbus-supply : external regulator + +AXP803 regulators, type, and corresponding input supply names: + +Regulator Type Supply Name Notes +--------- ---- ----------- ----- +DCDC1 : DC-DC buck : vin1-supply +DCDC2 : DC-DC buck : vin2-supply : poly-phase capable +DCDC3 : DC-DC buck : vin3-supply : poly-phase capable +DCDC4 : DC-DC buck : vin4-supply +DCDC5 : DC-DC buck : vin5-supply : poly-phase capable +DCDC6 : DC-DC buck : vin6-supply : poly-phase capable +DC1SW : On/Off Switch : : DCDC1 secondary output +ALDO1 : LDO : aldoin-supply : shared supply +ALDO2 : LDO : aldoin-supply : shared supply +ALDO3 : LDO : aldoin-supply : shared supply +DLDO1 : LDO : dldoin-supply : shared supply +DLDO2 : LDO : dldoin-supply : shared supply +DLDO3 : LDO : dldoin-supply : shared supply +DLDO4 : LDO : dldoin-supply : shared supply +ELDO1 : LDO : eldoin-supply : shared supply +ELDO2 : LDO : eldoin-supply : shared supply +ELDO3 : LDO : eldoin-supply : shared supply +FLDO1 : LDO : fldoin-supply : shared supply +FLDO2 : LDO : fldoin-supply : shared supply +LDO_IO0 : LDO : ips-supply : GPIO 0 +LDO_IO1 : LDO : ips-supply : GPIO 1 +RTC_LDO : LDO : ips-supply : always on + +AXP806 regulators, type, and corresponding input supply names: + +Regulator Type Supply Name Notes +--------- ---- ----------- ----- +DCDCA : DC-DC buck : vina-supply : poly-phase capable +DCDCB : DC-DC buck : vinb-supply : poly-phase capable +DCDCC : DC-DC buck : vinc-supply : poly-phase capable +DCDCD : DC-DC buck : vind-supply : poly-phase capable +DCDCE : DC-DC buck : vine-supply : poly-phase capable +ALDO1 : LDO : aldoin-supply : shared supply +ALDO2 : LDO : aldoin-supply : shared supply +ALDO3 : LDO : aldoin-supply : shared supply +BLDO1 : LDO : bldoin-supply : shared supply +BLDO2 : LDO : bldoin-supply : shared supply +BLDO3 : LDO : bldoin-supply : shared supply +BLDO4 : LDO : bldoin-supply : shared supply +CLDO1 : LDO : cldoin-supply : shared supply +CLDO2 : LDO : cldoin-supply : shared supply +CLDO3 : LDO : cldoin-supply : shared supply +SW : On/Off Switch : swin-supply + +Additionally, the AXP806 DC-DC regulators support poly-phase arrangements +for higher output current. The possible groupings are: A+B, A+B+C, D+E. + +AXP809 regulators, type, and corresponding input supply names: + +Regulator Type Supply Name Notes +--------- ---- ----------- ----- +DCDC1 : DC-DC buck : vin1-supply +DCDC2 : DC-DC buck : vin2-supply +DCDC3 : DC-DC buck : vin3-supply +DCDC4 : DC-DC buck : vin4-supply +DCDC5 : DC-DC buck : vin5-supply +DC1SW : On/Off Switch : : DCDC1 secondary output +DC5LDO : LDO : : input from DCDC5 +ALDO1 : LDO : aldoin-supply : shared supply +ALDO2 : LDO : aldoin-supply : shared supply +ALDO3 : LDO : aldoin-supply : shared supply +DLDO1 : LDO : dldoin-supply : shared supply +DLDO2 : LDO : dldoin-supply : shared supply +ELDO1 : LDO : eldoin-supply : shared supply +ELDO2 : LDO : eldoin-supply : shared supply +ELDO3 : LDO : eldoin-supply : shared supply +LDO_IO0 : LDO : ips-supply : GPIO 0 +LDO_IO1 : LDO : ips-supply : GPIO 1 +RTC_LDO : LDO : ips-supply : always on +SW : On/Off Switch : swin-supply Example: diff --git a/Documentation/devicetree/bindings/mfd/da9052-i2c.txt b/Documentation/devicetree/bindings/mfd/da9052-i2c.txt index 1857f4a6b9a9..9554292dc6cb 100644 --- a/Documentation/devicetree/bindings/mfd/da9052-i2c.txt +++ b/Documentation/devicetree/bindings/mfd/da9052-i2c.txt @@ -8,10 +8,13 @@ Sub-nodes: - regulators : Contain the regulator nodes. The DA9052/53 regulators are bound using their names as listed below: - buck0 : regulator BUCK0 - buck1 : regulator BUCK1 - buck2 : regulator BUCK2 - buck3 : regulator BUCK3 + buck1 : regulator BUCK CORE + buck2 : regulator BUCK PRO + buck3 : regulator BUCK MEM + buck4 : regulator BUCK PERI + ldo1 : regulator LDO1 + ldo2 : regulator LDO2 + ldo3 : regulator LDO3 ldo4 : regulator LDO4 ldo5 : regulator LDO5 ldo6 : regulator LDO6 @@ -19,9 +22,6 @@ Sub-nodes: ldo8 : regulator LDO8 ldo9 : regulator LDO9 ldo10 : regulator LDO10 - ldo11 : regulator LDO11 - ldo12 : regulator LDO12 - ldo13 : regulator LDO13 The bindings details of individual regulator device can be found in: Documentation/devicetree/bindings/regulator/regulator.txt @@ -36,22 +36,22 @@ i2c@63fc8000 { /* I2C1 */ reg = <0x48>; regulators { - buck0 { + buck1 { regulator-min-microvolt = <500000>; regulator-max-microvolt = <2075000>; }; - buck1 { + buck2 { regulator-min-microvolt = <500000>; regulator-max-microvolt = <2075000>; }; - buck2 { + buck3 { regulator-min-microvolt = <925000>; regulator-max-microvolt = <2500000>; }; - buck3 { + buck4 { regulator-min-microvolt = <925000>; regulator-max-microvolt = <2500000>; }; diff --git a/Documentation/devicetree/bindings/mfd/da9062.txt b/Documentation/devicetree/bindings/mfd/da9062.txt index 38802b54d48a..c0a418c27e9d 100644 --- a/Documentation/devicetree/bindings/mfd/da9062.txt +++ b/Documentation/devicetree/bindings/mfd/da9062.txt @@ -1,22 +1,39 @@ * Dialog DA9062 Power Management Integrated Circuit (PMIC) -DA9062 consists of a large and varied group of sub-devices: +Product information for the DA9062 and DA9061 devices can be found here: +- http://www.dialog-semiconductor.com/products/da9062 +- http://www.dialog-semiconductor.com/products/da9061 + +The DA9062 PMIC consists of: Device Supply Names Description ------ ------------ ----------- da9062-regulator : : LDOs & BUCKs da9062-rtc : : Real-Time Clock +da9062-onkey : : On Key +da9062-watchdog : : Watchdog Timer +da9062-thermal : : Thermal + +The DA9061 PMIC consists of: + +Device Supply Names Description +------ ------------ ----------- +da9062-regulator : : LDOs & BUCKs +da9062-onkey : : On Key da9062-watchdog : : Watchdog Timer +da9062-thermal : : Thermal ====== Required properties: -- compatible : Should be "dlg,da9062". +- compatible : Should be + "dlg,da9062" for DA9062 + "dlg,da9061" for DA9061 - reg : Specifies the I2C slave address (this defaults to 0x58 but it can be modified to match the chip's OTP settings). - interrupt-parent : Specifies the reference to the interrupt controller for - the DA9062. + the DA9062 or DA9061. - interrupts : IRQ line information. - interrupt-controller @@ -25,8 +42,8 @@ further information on IRQ bindings. Sub-nodes: -- regulators : This node defines the settings for the LDOs and BUCKs. The - DA9062 regulators are bound using their names listed below: +- regulators : This node defines the settings for the LDOs and BUCKs. + The DA9062 regulators are bound using their names listed below: buck1 : BUCK_1 buck2 : BUCK_2 @@ -37,19 +54,29 @@ Sub-nodes: ldo3 : LDO_3 ldo4 : LDO_4 + The DA9061 regulators are bound using their names listed below: + + buck1 : BUCK_1 + buck2 : BUCK_2 + buck3 : BUCK_3 + ldo1 : LDO_1 + ldo2 : LDO_2 + ldo3 : LDO_3 + ldo4 : LDO_4 + The component follows the standard regulator framework and the bindings details of individual regulator device can be found in: Documentation/devicetree/bindings/regulator/regulator.txt - - rtc : This node defines settings required for the Real-Time Clock associated with the DA9062. There are currently no entries in this binding, however compatible = "dlg,da9062-rtc" should be added if a node is created. -- watchdog: This node defines the settings for the watchdog driver associated - with the DA9062 PMIC. The compatible = "dlg,da9062-watchdog" should be added - if a node is created. +- onkey : See ../input/da9062-onkey.txt + +- watchdog: See ../watchdog/da9062-watchdog.txt +- thermal : See ../thermal/da9062-thermal.txt Example: @@ -64,10 +91,6 @@ Example: compatible = "dlg,da9062-rtc"; }; - watchdog { - compatible = "dlg,da9062-watchdog"; - }; - regulators { DA9062_BUCK1: buck1 { regulator-name = "BUCK1"; diff --git a/Documentation/devicetree/bindings/mfd/fsl-imx25-tsadc.txt b/Documentation/devicetree/bindings/mfd/fsl-imx25-tsadc.txt new file mode 100644 index 000000000000..b03505286997 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/fsl-imx25-tsadc.txt @@ -0,0 +1,47 @@ +Freescale MX25 ADC/TSC MultiFunction Device (MFD) + +This device combines two general purpose conversion queues one used for general +ADC and the other used for touchscreens. + +Required properties: + - compatible: Should be "fsl,imx25-tsadc". + - reg: Start address and size of the memory area of + the device + - interrupts: Interrupt for this device + (See: ../interrupt-controller/interrupts.txt) + - clocks: An 'ipg' clock (See: ../clock/clock-bindings.txt) + - interrupt-controller: This device is an interrupt controller. It + controls the interrupts of both + conversion queues. + - #interrupt-cells: Should be '<1>'. + - #address-cells: Should be '<1>'. + - #size-cells: Should be '<1>'. + +This device includes two conversion queues which can be added as subnodes. +The first queue is for the touchscreen, the second for general purpose ADC. + +Example: + tscadc: tscadc@50030000 { + compatible = "fsl,imx25-tsadc"; + reg = <0x50030000 0xc>; + interrupts = <46>; + clocks = <&clks 119>; + clock-names = "ipg"; + interrupt-controller; + #interrupt-cells = <1>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + tsc: tcq@50030400 { + compatible = "fsl,imx25-tcq"; + reg = <0x50030400 0x60>; + ... + }; + + adc: gcq@50030800 { + compatible = "fsl,imx25-gcq"; + reg = <0x50030800 0x60>; + ... + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/hi6421.txt b/Documentation/devicetree/bindings/mfd/hi6421.txt index 0d5a4466a494..22da96d344a7 100644 --- a/Documentation/devicetree/bindings/mfd/hi6421.txt +++ b/Documentation/devicetree/bindings/mfd/hi6421.txt @@ -1,7 +1,9 @@ * HI6421 Multi-Functional Device (MFD), by HiSilicon Ltd. Required parent device properties: -- compatible : contains "hisilicon,hi6421-pmic"; +- compatible : One of the following chip-specific strings: + "hisilicon,hi6421-pmic"; + "hisilicon,hi6421v530-pmic"; - reg : register range space of hi6421; Supported Hi6421 sub-devices include: diff --git a/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt b/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt new file mode 100644 index 000000000000..9630ac0e4b56 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt @@ -0,0 +1,33 @@ +Hisilicon Hi655x Power Management Integrated Circuit (PMIC) + +The hardware layout for access PMIC Hi655x from AP SoC Hi6220. +Between PMIC Hi655x and Hi6220, the physical signal channel is SSI. +We can use memory-mapped I/O to communicate. + ++----------------+ +-------------+ +| | | | +| Hi6220 | SSI bus | Hi655x | +| |-------------| | +| |(REGMAP_MMIO)| | ++----------------+ +-------------+ + +Required properties: +- compatible: Should be "hisilicon,hi655x-pmic". +- reg: Base address of PMIC on Hi6220 SoC. +- interrupt-controller: Hi655x has internal IRQs (has own IRQ domain). +- pmic-gpios: The GPIO used by PMIC IRQ. +- #clock-cells: From common clock binding; shall be set to 0 + +Optional properties: +- clock-output-names: From common clock binding to override the + default output clock name + +Example: + pmic: pmic@f8000000 { + compatible = "hisilicon,hi655x-pmic"; + reg = <0x0 0xf8000000 0x0 0x1000>; + interrupt-controller; + #interrupt-cells = <2>; + pmic-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; + #clock-cells = <0>; + } diff --git a/Documentation/devicetree/bindings/mfd/lp873x.txt b/Documentation/devicetree/bindings/mfd/lp873x.txt new file mode 100644 index 000000000000..ae9cf39bd101 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/lp873x.txt @@ -0,0 +1,67 @@ +TI LP873X PMIC MFD driver + +Required properties: + - compatible: "ti,lp8732", "ti,lp8733" + - reg: I2C slave address. + - gpio-controller: Marks the device node as a GPIO Controller. + - #gpio-cells: Should be two. The first cell is the pin number and + the second cell is used to specify flags. + See ../gpio/gpio.txt for more information. + - xxx-in-supply: Phandle to parent supply node of each regulator + populated under regulators node. xxx can be + buck0, buck1, ldo0 or ldo1. + - regulators: List of child nodes that specify the regulator + initialization data. +Example: + +pmic: lp8733@60 { + compatible = "ti,lp8733"; + reg = <0x60>; + gpio-controller; + #gpio-cells = <2>; + + buck0-in-supply = <&vsys_3v3>; + buck1-in-supply = <&vsys_3v3>; + ldo0-in-supply = <&vsys_3v3>; + ldo1-in-supply = <&vsys_3v3>; + + regulators { + lp8733_buck0: buck0 { + regulator-name = "lp8733-buck0"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-min-microamp = <1500000>; + regulator-max-microamp = <4000000>; + regulator-ramp-delay = <10000>; + regulator-always-on; + regulator-boot-on; + }; + + lp8733_buck1: buck1 { + regulator-name = "lp8733-buck1"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-min-microamp = <1500000>; + regulator-max-microamp = <4000000>; + regulator-ramp-delay = <10000>; + regulator-boot-on; + regulator-always-on; + }; + + lp8733_ldo0: ldo0 { + regulator-name = "lp8733-ldo0"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + lp8733_ldo1: ldo1 { + regulator-name = "lp8733-ldo1"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + regulator-boot-on; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/lp87565.txt b/Documentation/devicetree/bindings/mfd/lp87565.txt new file mode 100644 index 000000000000..a48df7c08ab0 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/lp87565.txt @@ -0,0 +1,43 @@ +TI LP87565 PMIC MFD driver + +Required properties: + - compatible: "ti,lp87565", "ti,lp87565-q1" + - reg: I2C slave address. + - gpio-controller: Marks the device node as a GPIO Controller. + - #gpio-cells: Should be two. The first cell is the pin number and + the second cell is used to specify flags. + See ../gpio/gpio.txt for more information. + - xxx-in-supply: Phandle to parent supply node of each regulator + populated under regulators node. xxx should match + the supply_name populated in driver. +Example: + +lp87565_pmic: pmic@60 { + compatible = "ti,lp87565-q1"; + reg = <0x60>; + gpio-controller; + #gpio-cells = <2>; + + buck10-in-supply = <&vsys_3v3>; + buck23-in-supply = <&vsys_3v3>; + + regulators: regulators { + buck10_reg: buck10 { + /* VDD_MPU */ + regulator-name = "buck10"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + }; + + buck23_reg: buck23 { + /* VDD_GPU */ + regulator-name = "buck23"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1250000>; + regulator-boot-on; + regulator-always-on; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/max77620.txt b/Documentation/devicetree/bindings/mfd/max77620.txt new file mode 100644 index 000000000000..9c16d51cc15b --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max77620.txt @@ -0,0 +1,155 @@ +MAX77620 Power management IC from Maxim Semiconductor. + +Required properties: +------------------- +- compatible: Must be one of + "maxim,max77620" + "maxim,max20024". +- reg: I2C device address. + +Optional properties: +------------------- +- interrupts: The interrupt on the parent the controller is + connected to. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: is <2> and their usage is compliant to the 2 cells + variant of <../interrupt-controller/interrupts.txt> + IRQ numbers for different interrupt source of MAX77620 + are defined at dt-bindings/mfd/max77620.h. + +Optional subnodes and their properties: +======================================= + +Flexible power sequence configurations: +-------------------------------------- +The Flexible Power Sequencer (FPS) allows each regulator to power up under +hardware or software control. Additionally, each regulator can power on +independently or among a group of other regulators with an adjustable power-up +and power-down delays (sequencing). GPIO1, GPIO2, and GPIO3 can be programmed +to be part of a sequence allowing external regulators to be sequenced along +with internal regulators. 32KHz clock can be programmed to be part of a +sequence. + +The flexible sequencing structure consists of two hardware enable inputs +(EN0, EN1), and 3 master sequencing timers called FPS0, FPS1 and FPS2. +Each master sequencing timer is programmable through its configuration +register to have a hardware enable source (EN1 or EN2) or a software enable +source (SW). When enabled/disabled, the master sequencing timer generates +eight sequencing events on different time periods called slots. The time +period between each event is programmable within the configuration register. +Each regulator, GPIO1, GPIO2, GPIO3, and 32KHz clock has a flexible power +sequence slave register which allows its enable source to be specified as +a flexible power sequencer timer or a software bit. When a FPS source of +regulators, GPIOs and clocks specifies the enable source to be a flexible +power sequencer, the power up and power down delays can be specified in +the regulators, GPIOs and clocks flexible power sequencer configuration +registers. + +When FPS event cleared (set to LOW), regulators, GPIOs and 32KHz +clock are set into following state at the sequencing event that +corresponds to its flexible sequencer configuration register. + Sleep state: In this state, regulators, GPIOs + and 32KHz clock get disabled at + the sequencing event. + Global Low Power Mode (GLPM): In this state, regulators are set in + low power mode at the sequencing event. + +The configuration parameters of FPS is provided through sub-node "fps" +and their child for FPS specific. The child node name for FPS are "fps0", +"fps1", and "fps2" for FPS0, FPS1 and FPS2 respectively. + +The FPS configurations like FPS source, power up and power down slots for +regulators, GPIOs and 32kHz clocks are provided in their respective +configuration nodes which is explained in respective sub-system DT +binding document. + +There is need for different FPS configuration parameters based on system +state like when system state changed from active to suspend or active to +power off (shutdown). + +Optional properties: +------------------- +-maxim,fps-event-source: u32, FPS event source like external + hardware input to PMIC i.e. EN0, EN1 or + software (SW). + The macros are defined on + dt-bindings/mfd/max77620.h + for different control source. + - MAX77620_FPS_EVENT_SRC_EN0 + for hardware input pin EN0. + - MAX77620_FPS_EVENT_SRC_EN1 + for hardware input pin EN1. + - MAX77620_FPS_EVENT_SRC_SW + for software control. + +-maxim,shutdown-fps-time-period-us: u32, FPS time period in microseconds + when system enters in to shutdown + state. + +-maxim,suspend-fps-time-period-us: u32, FPS time period in microseconds + when system enters in to suspend state. + +-maxim,device-state-on-disabled-event: u32, describe the PMIC state when FPS + event cleared (set to LOW) whether it + should go to sleep state or low-power + state. Following are valid values: + - MAX77620_FPS_INACTIVE_STATE_SLEEP + to set the PMIC state to sleep. + - MAX77620_FPS_INACTIVE_STATE_LOW_POWER + to set the PMIC state to low + power. + Absence of this property or other value + will not change device state when FPS + event get cleared. + +Here supported time periods by device in microseconds are as follows: +MAX77620 supports 40, 80, 160, 320, 640, 1280, 2560 and 5120 microseconds. +MAX20024 supports 20, 40, 80, 160, 320, 640, 1280 and 2540 microseconds. + +-maxim,power-ok-control: configure map power ok bit + 1: Enables POK(Power OK) to control nRST_IO and GPIO1 + POK function. + 0: Disables POK control. + if property missing, do not configure MPOK bit. + If POK mapping is enabled for GPIO1/nRST_IO then, + GPIO1/nRST_IO pins are HIGH only if all rails + that have POK control enabled are HIGH. + If any of the rails goes down(which are enabled for POK + control) then, GPIO1/nRST_IO goes LOW. + this property is valid for max20024 only. + +For DT binding details of different sub modules like GPIO, pincontrol, +regulator, power, please refer respective device-tree binding document +under their respective sub-system directories. + +Example: +-------- +#include <dt-bindings/mfd/max77620.h> + +max77620@3c { + compatible = "maxim,max77620"; + reg = <0x3c>; + + interrupt-parent = <&intc>; + interrupts = <0 86 IRQ_TYPE_NONE>; + + interrupt-controller; + #interrupt-cells = <2>; + + fps { + fps0 { + maxim,shutdown-fps-time-period-us = <1280>; + maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN1>; + }; + + fps1 { + maxim,shutdown-fps-time-period-us = <1280>; + maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>; + }; + + fps2 { + maxim,shutdown-fps-time-period-us = <1280>; + maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_SW>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt index d3425846aa5b..6a1ae3a2b77f 100644 --- a/Documentation/devicetree/bindings/mfd/max77693.txt +++ b/Documentation/devicetree/bindings/mfd/max77693.txt @@ -17,28 +17,28 @@ Required properties: - interrupt-parent : The parent interrupt controller. Optional properties: -- regulators : The regulators of max77693 have to be instantiated under subnod +- regulators : The regulators of max77693 have to be instantiated under subnode named "regulators" using the following format. regulators { - regualtor-compatible = ESAFEOUT1/ESAFEOUT2/CHARGER - standard regulator constratints[*]. + regulator-compatible = ESAFEOUT1/ESAFEOUT2/CHARGER + standard regulator constraints[*]. }; [*] refer Documentation/devicetree/bindings/regulator/regulator.txt - haptic : The MAX77693 haptic device utilises a PWM controlled motor to provide users with tactile feedback. PWM period and duty-cycle are varied in - order to provide the approprite level of feedback. + order to provide the appropriate level of feedback. Required properties: - - compatible : Must be "maxim,max77693-hpatic" + - compatible : Must be "maxim,max77693-haptic" - haptic-supply : power supply for the haptic motor [*] refer Documentation/devicetree/bindings/regulator/regulator.txt - pwms : phandle to the physical PWM(Pulse Width Modulation) device. PWM properties should be named "pwms". And number of cell is different for each pwm device. - To get more informations, please refer to documentaion. + To get more information, please refer to documentation. [*] refer Documentation/devicetree/bindings/pwm/pwm.txt - charger : Node configuring the charger driver. diff --git a/Documentation/devicetree/bindings/mfd/mfd.txt b/Documentation/devicetree/bindings/mfd/mfd.txt index af9d6931a1a2..bcb6abb9d413 100644 --- a/Documentation/devicetree/bindings/mfd/mfd.txt +++ b/Documentation/devicetree/bindings/mfd/mfd.txt @@ -19,12 +19,22 @@ Optional properties: - compatible : "simple-mfd" - this signifies that the operating system should consider all subnodes of the MFD device as separate devices akin to how - "simple-bus" inidicates when to see subnodes as children for a simple + "simple-bus" indicates when to see subnodes as children for a simple memory-mapped bus. For more complex devices, when the nexus driver has to probe registers to figure out what child devices exist etc, this should not be used. In the latter case the child devices will be determined by the operating system. +- ranges: Describes the address mapping relationship to the parent. Should set + the child's base address to 0, the physical address within parent's address + space, and the length of the address map. + +- #address-cells: Specifies the number of cells used to represent physical base + addresses. Must be present if ranges is used. + +- #size-cells: Specifies the number of cells used to represent the size of an + address. Must be present if ranges is used. + Example: foo@1000 { diff --git a/Documentation/devicetree/bindings/mfd/motorola-cpcap.txt b/Documentation/devicetree/bindings/mfd/motorola-cpcap.txt new file mode 100644 index 000000000000..15bc885f9df4 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/motorola-cpcap.txt @@ -0,0 +1,31 @@ +Motorola CPCAP PMIC device tree binding + +Required properties: +- compatible : One or both of "motorola,cpcap" or "ste,6556002" +- reg : SPI chip select +- interrupt-parent : The parent interrupt controller +- interrupts : The interrupt line the device is connected to +- interrupt-controller : Marks the device node as an interrupt controller +- #interrupt-cells : The number of cells to describe an IRQ, should be 2 +- #address-cells : Child device offset number of cells, should be 1 +- #size-cells : Child device size number of cells, should be 0 +- spi-max-frequency : Typically set to 3000000 +- spi-cs-high : SPI chip select direction + +Example: + +&mcspi1 { + cpcap: pmic@0 { + compatible = "motorola,cpcap", "ste,6556002"; + reg = <0>; /* cs0 */ + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_EDGE_RISING>; + interrupt-controller; + #interrupt-cells = <2>; + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <3000000>; + spi-cs-high; + }; +}; + diff --git a/Documentation/devicetree/bindings/mfd/mt6397.txt b/Documentation/devicetree/bindings/mfd/mt6397.txt index 15043e652699..522a3bbf1bac 100644 --- a/Documentation/devicetree/bindings/mfd/mt6397.txt +++ b/Documentation/devicetree/bindings/mfd/mt6397.txt @@ -1,21 +1,22 @@ -MediaTek MT6397 Multifunction Device Driver +MediaTek MT6397/MT6323 Multifunction Device Driver -MT6397 is a multifunction device with the following sub modules: +MT6397/MT6323 is a multifunction device with the following sub modules: - Regulator - RTC - Audio codec - GPIO - Clock +- LED It is interfaced to host controller using SPI interface by a proprietary hardware -called PMIC wrapper or pwrap. MT6397 MFD is a child device of pwrap. +called PMIC wrapper or pwrap. MT6397/MT6323 MFD is a child device of pwrap. See the following for pwarp node definitions: Documentation/devicetree/bindings/soc/pwrap.txt This document describes the binding for MFD device and its sub module. Required properties: -compatible: "mediatek,mt6397" +compatible: "mediatek,mt6397" or "mediatek,mt6323" Optional subnodes: @@ -26,12 +27,18 @@ Optional subnodes: Required properties: - compatible: "mediatek,mt6397-regulator" see Documentation/devicetree/bindings/regulator/mt6397-regulator.txt + - compatible: "mediatek,mt6323-regulator" + see Documentation/devicetree/bindings/regulator/mt6323-regulator.txt - codec Required properties: - compatible: "mediatek,mt6397-codec" - clk Required properties: - compatible: "mediatek,mt6397-clk" +- led + Required properties: + - compatible: "mediatek,mt6323-led" + see Documentation/devicetree/bindings/leds/leds-mt6323.txt Example: pwrap: pwrap@1000f000 { diff --git a/Documentation/devicetree/bindings/mfd/mxs-lradc.txt b/Documentation/devicetree/bindings/mfd/mxs-lradc.txt new file mode 100644 index 000000000000..555fb117d4fa --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/mxs-lradc.txt @@ -0,0 +1,47 @@ +* Freescale MXS LRADC device driver + +Required properties: +- compatible: Should be "fsl,imx23-lradc" for i.MX23 SoC and "fsl,imx28-lradc" + for i.MX28 SoC +- reg: Address and length of the register set for the device +- interrupts: Should contain the LRADC interrupts + +Optional properties: +- fsl,lradc-touchscreen-wires: Number of wires used to connect the touchscreen + to LRADC. Valid value is either 4 or 5. If this + property is not present, then the touchscreen is + disabled. 5 wires is valid for i.MX28 SoC only. +- fsl,ave-ctrl: number of samples per direction to calculate an average value. + Allowed value is 1 ... 32, default is 4 +- fsl,ave-delay: delay between consecutive samples. Allowed value is + 2 ... 2048. It is used if 'fsl,ave-ctrl' > 1, counts at + 2 kHz and its default is 2 (= 1 ms) +- fsl,settling: delay between plate switch to next sample. Allowed value is + 1 ... 2047. It counts at 2 kHz and its default is + 10 (= 5 ms) + +Example for i.MX23 SoC: + + lradc@80050000 { + compatible = "fsl,imx23-lradc"; + reg = <0x80050000 0x2000>; + interrupts = <36 37 38 39 40 41 42 43 44>; + status = "okay"; + fsl,lradc-touchscreen-wires = <4>; + fsl,ave-ctrl = <4>; + fsl,ave-delay = <2>; + fsl,settling = <10>; + }; + +Example for i.MX28 SoC: + + lradc@80050000 { + compatible = "fsl,imx28-lradc"; + reg = <0x80050000 0x2000>; + interrupts = <10 14 15 16 17 18 19 20 21 22 23 24 25>; + status = "okay"; + fsl,lradc-touchscreen-wires = <5>; + fsl,ave-ctrl = <4>; + fsl,ave-delay = <2>; + fsl,settling = <10>; + }; diff --git a/Documentation/devicetree/bindings/mfd/omap-usb-host.txt b/Documentation/devicetree/bindings/mfd/omap-usb-host.txt index 4721b2d521e4..aa1eaa59581b 100644 --- a/Documentation/devicetree/bindings/mfd/omap-usb-host.txt +++ b/Documentation/devicetree/bindings/mfd/omap-usb-host.txt @@ -64,8 +64,8 @@ Required properties if child node exists: Properties for children: The OMAP HS USB Host subsystem contains EHCI and OHCI controllers. -See Documentation/devicetree/bindings/usb/omap-ehci.txt and -omap3-ohci.txt +See Documentation/devicetree/bindings/usb/ehci-omap.txt and +Documentation/devicetree/bindings/usb/ohci-omap3.txt. Example for OMAP4: diff --git a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt index f24f33409164..9e5eba4a4f0d 100644 --- a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt +++ b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt @@ -10,6 +10,7 @@ voltages and other various functionality to Qualcomm SoCs. Value type: <string> Definition: must be one of: "qcom,pm8058" + "qcom,pm8821" "qcom,pm8921" - #address-cells: @@ -62,6 +63,7 @@ The below bindings specify the set of valid subnodes. "qcom,pm8058-rtc" "qcom,pm8921-rtc" "qcom,pm8941-rtc" + "qcom,pm8018-rtc" - reg: Usage: required diff --git a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt index 5e97a9593ad7..3c91ad430eea 100644 --- a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt +++ b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt @@ -13,6 +13,7 @@ frequencies. "qcom,rpm-msm8660" "qcom,rpm-msm8960" "qcom,rpm-ipq8064" + "qcom,rpm-mdm9615" - reg: Usage: required @@ -59,6 +60,7 @@ Regulator nodes are identified by their compatible: "qcom,rpm-pm8058-regulators" "qcom,rpm-pm8901-regulators" "qcom,rpm-pm8921-regulators" + "qcom,rpm-pm8018-regulators" - vdd_l0_l1_lvs-supply: - vdd_l2_l11_l12-supply: @@ -137,6 +139,15 @@ Regulator nodes are identified by their compatible: Definition: reference to regulator supplying the input pin, as described in the data sheet +- vin_lvs1-supply: +- vdd_l7-supply: +- vdd_l8-supply: +- vdd_l9_l10_l11_l12-supply: + Usage: optional (pm8018 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + The regulator node houses sub-nodes for each regulator within the device. Each sub-node is identified using the node's name, with valid values listed for each of the pmics below. @@ -156,6 +167,10 @@ pm8921: l29, lvs1, lvs2, lvs3, lvs4, lvs5, lvs6, lvs7, usb-switch, hdmi-switch, ncp +pm8018: + s1, s2, s3, s4, s5, , l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, + l12, l14, lvs1 + The content of each sub-node is defined by the standard binding for regulators - see regulator.txt - with additional custom properties described below: @@ -178,7 +193,7 @@ see regulator.txt - with additional custom properties described below: - qcom,force-mode: Usage: optional (default if no other qcom,force-mode is specified) Value type: <u32> - Defintion: indicates that the regulator should be forced to a + Definition: indicates that the regulator should be forced to a particular mode, valid values are: QCOM_RPM_FORCE_MODE_NONE - do not force any mode QCOM_RPM_FORCE_MODE_LPM - force into low power mode @@ -204,7 +219,7 @@ see regulator.txt - with additional custom properties described below: - qcom,force-mode: Usage: optional Value type: <u32> - Defintion: indicates that the regulator should not be forced to any + Definition: indicates that the regulator should not be forced to any particular mode, valid values are: QCOM_RPM_FORCE_MODE_NONE - do not force any mode QCOM_RPM_FORCE_MODE_LPM - force into low power mode @@ -219,7 +234,7 @@ see regulator.txt - with additional custom properties described below: - qcom,switch-mode-frequency: Usage: required Value type: <u32> - Definition: Frequency (Hz) of the swith mode power supply; + Definition: Frequency (Hz) of the switch mode power supply; must be one of: 19200000, 9600000, 6400000, 4800000, 3840000, 3200000, 2740000, 2400000, 2130000, 1920000, 1750000, 1600000, diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt index 4ca6aab4273a..9636ae8d8d41 100644 --- a/Documentation/devicetree/bindings/mfd/rk808.txt +++ b/Documentation/devicetree/bindings/mfd/rk808.txt @@ -1,7 +1,11 @@ -RK808 Power Management Integrated Circuit +RK8XX Power Management Integrated Circuit + +The rk8xx family current members: +rk808 +rk818 Required properties: -- compatible: "rockchip,rk808" +- compatible: "rockchip,rk808", "rockchip,rk818" - reg: I2C slave address - interrupt-parent: The parent interrupt controller. - interrupts: the interrupt outputs of the controller. @@ -13,6 +17,8 @@ Optional properties: default output clock name - rockchip,system-power-controller: Telling whether or not this pmic is controlling the system power. + +Optional RK808 properties: - vcc1-supply: The input supply for DCDC_REG1 - vcc2-supply: The input supply for DCDC_REG2 - vcc3-supply: The input supply for DCDC_REG3 @@ -29,7 +35,20 @@ Optional properties: the gpio controller. If DVS GPIOs aren't present, voltage changes will happen very quickly with no slow ramp time. -Regulators: All the regulators of RK808 to be instantiated shall be +Optional RK818 properties: +- vcc1-supply: The input supply for DCDC_REG1 +- vcc2-supply: The input supply for DCDC_REG2 +- vcc3-supply: The input supply for DCDC_REG3 +- vcc4-supply: The input supply for DCDC_REG4 +- boost-supply: The input supply for DCDC_BOOST +- vcc6-supply: The input supply for LDO_REG1 and LDO_REG2 +- vcc7-supply: The input supply for LDO_REG3, LDO_REG5 and LDO_REG7 +- vcc8-supply: The input supply for LDO_REG4, LDO_REG6 and LDO_REG8 +- vcc9-supply: The input supply for LDO_REG9 and SWITCH_REG +- h_5v-supply: The input supply for HDMI_SWITCH +- usb-supply: The input supply for OTG_SWITCH + +Regulators: All the regulators of RK8XX to be instantiated shall be listed in a child node named 'regulators'. Each regulator is represented by a child node of the 'regulators' node. @@ -48,6 +67,18 @@ number as described in RK808 datasheet. - SWITCH_REGn - valid values for n are 1 to 2 +Following regulators of the RK818 PMIC block are supported. Note that +the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO +number as described in RK818 datasheet. + + - DCDC_REGn + - valid values for n are 1 to 4. + - LDO_REGn + - valid values for n are 1 to 9. + - SWITCH_REG + - HDMI_SWITCH + - OTG_SWITCH + Standard regulator bindings are used inside regulator subnodes. Check Documentation/devicetree/bindings/regulator/regulator.txt for more details diff --git a/Documentation/devicetree/bindings/mfd/rn5t618.txt b/Documentation/devicetree/bindings/mfd/rn5t618.txt index 937785a3eddc..65c23263cc54 100644 --- a/Documentation/devicetree/bindings/mfd/rn5t618.txt +++ b/Documentation/devicetree/bindings/mfd/rn5t618.txt @@ -1,18 +1,25 @@ -* Ricoh RN5T618 PMIC +* Ricoh RN5T567/RN5T618 PMIC -Ricoh RN5T618 is a power management IC which integrates 3 step-down -DCDC converters, 7 low-dropout regulators, a Li-ion battery charger, -fuel gauge, ADC, GPIOs and a watchdog timer. It can be controlled -through a I2C interface. +Ricoh RN5T567/RN5T618/RC5T619 is a power management IC family which +integrates 3 to 5 step-down DCDC converters, 7 to 10 low-dropout regulators, +GPIOs, and a watchdog timer. It can be controlled through an I2C interface. +The RN5T618/RC5T619 provides additionally a Li-ion battery charger, +fuel gauge, and an ADC. +The RC5T619 additionnally includes USB charger detection and an RTC. Required properties: - - compatible: should be "ricoh,rn5t618" + - compatible: must be one of + "ricoh,rn5t567" + "ricoh,rn5t618" + "ricoh,rc5t619" - reg: the I2C slave address of the device Sub-nodes: - regulators: the node is required if the regulator functionality is - needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, LDO1, - LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2. + needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, DCDC4 + (RN5T567/RC5T619), LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7, LDO8, + LDO9, LDO10, LDORTC1 and LDORTC2. + LDO7-10 are specific to RC5T619. The common bindings for each individual regulator can be found in: Documentation/devicetree/bindings/regulator/regulator.txt diff --git a/Documentation/devicetree/bindings/mfd/samsung,exynos5433-lpass.txt b/Documentation/devicetree/bindings/mfd/samsung,exynos5433-lpass.txt new file mode 100644 index 000000000000..df664018c148 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/samsung,exynos5433-lpass.txt @@ -0,0 +1,74 @@ +Samsung Exynos SoC Low Power Audio Subsystem (LPASS) + +Required properties: + + - compatible : "samsung,exynos5433-lpass" + - reg : should contain the LPASS top SFR region location + and size + - clock-names : should contain following required clocks: "sfr0_ctrl" + - clocks : should contain clock specifiers of all clocks, which + input names have been specified in clock-names + property, in same order. + - #address-cells : should be 1 + - #size-cells : should be 1 + - ranges : must be present + +Each IP block of the Low Power Audio Subsystem should be specified as +an optional sub-node. For "samsung,exynos5433-lpass" compatible this includes: +UART, SLIMBUS, PCM, I2S, DMAC, Timers 0...4, VIC, WDT 0...1 devices. + +Bindings of the sub-nodes are described in: + ../serial/samsung_uart.txt + ../sound/samsung-i2s.txt + ../dma/arm-pl330.txt + + +Example: + +audio-subsystem { + compatible = "samsung,exynos5433-lpass"; + reg = <0x11400000 0x100>, <0x11500000 0x08>; + clocks = <&cmu_aud CLK_PCLK_SFR0_CTRL>; + clock-names = "sfr0_ctrl"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + adma: adma@11420000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x11420000 0x1000>; + interrupts = <0 73 0>; + clocks = <&cmu_aud CLK_ACLK_DMAC>; + clock-names = "apb_pclk"; + #dma-cells = <1>; + #dma-channels = <8>; + #dma-requests = <32>; + }; + + i2s0: i2s0@11440000 { + compatible = "samsung,exynos7-i2s"; + reg = <0x11440000 0x100>; + dmas = <&adma 0 &adma 2>; + dma-names = "tx", "rx"; + interrupts = <0 70 0>; + clocks = <&cmu_aud CLK_PCLK_AUD_I2S>, + <&cmu_aud CLK_SCLK_AUD_I2S>, + <&cmu_aud CLK_SCLK_I2S_BCLK>; + clock-names = "iis", "i2s_opclk0", "i2s_opclk1"; + pinctrl-names = "default"; + pinctrl-0 = <&i2s0_bus>; + status = "disabled"; + }; + + serial_3: serial@11460000 { + compatible = "samsung,exynos5433-uart"; + reg = <0x11460000 0x100>; + interrupts = <0 67 0>; + clocks = <&cmu_aud CLK_PCLK_AUD_UART>, + <&cmu_aud CLK_SCLK_AUD_UART>; + clock-names = "uart", "clk_uart_baud0"; + pinctrl-names = "default"; + pinctrl-0 = <&uart_aud_bus>; + status = "disabled"; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/stm32-timers.txt b/Documentation/devicetree/bindings/mfd/stm32-timers.txt new file mode 100644 index 000000000000..1db6e0057a63 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/stm32-timers.txt @@ -0,0 +1,46 @@ +STM32 Timers driver bindings + +This IP provides 3 types of timer along with PWM functionality: +- advanced-control timers consist of a 16-bit auto-reload counter driven by a programmable + prescaler, break input feature, PWM outputs and complementary PWM ouputs channels. +- general-purpose timers consist of a 16-bit or 32-bit auto-reload counter driven by a + programmable prescaler and PWM outputs. +- basic timers consist of a 16-bit auto-reload counter driven by a programmable prescaler. + +Required parameters: +- compatible: must be "st,stm32-timers" + +- reg: Physical base address and length of the controller's + registers. +- clock-names: Set to "int". +- clocks: Phandle to the clock used by the timer module. + For Clk properties, please refer to ../clock/clock-bindings.txt + +Optional parameters: +- resets: Phandle to the parent reset controller. + See ../reset/st,stm32-rcc.txt + +Optional subnodes: +- pwm: See ../pwm/pwm-stm32.txt +- timer: See ../iio/timer/stm32-timer-trigger.txt + +Example: + timers@40010000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40010000 0x400>; + clocks = <&rcc 0 160>; + clock-names = "int"; + + pwm { + compatible = "st,stm32-pwm"; + pinctrl-0 = <&pwm1_pins>; + pinctrl-names = "default"; + }; + + timer@0 { + compatible = "st,stm32-timer-trigger"; + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt index 3fb68bfefc8b..f9065a5781a2 100644 --- a/Documentation/devicetree/bindings/mfd/stmpe.txt +++ b/Documentation/devicetree/bindings/mfd/stmpe.txt @@ -4,7 +4,7 @@ STMPE is an MFD device which may expose the following inbuilt devices: gpio, keypad, touchscreen, adc, pwm, rotator. Required properties: - - compatible : "st,stmpe[610|801|811|1601|2401|2403]" + - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]" - reg : I2C/SPI address of the device Optional properties: diff --git a/Documentation/devicetree/bindings/mfd/sun4i-gpadc.txt b/Documentation/devicetree/bindings/mfd/sun4i-gpadc.txt new file mode 100644 index 000000000000..badff3611a98 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/sun4i-gpadc.txt @@ -0,0 +1,59 @@ +Allwinner SoCs' GPADC Device Tree bindings +------------------------------------------ +The Allwinner SoCs all have an ADC that can also act as a thermal sensor +and sometimes as a touchscreen controller. + +Required properties: + - compatible: "allwinner,sun8i-a33-ths", + - reg: mmio address range of the chip, + - #thermal-sensor-cells: shall be 0, + - #io-channel-cells: shall be 0, + +Example: + ths: ths@01c25000 { + compatible = "allwinner,sun8i-a33-ths"; + reg = <0x01c25000 0x100>; + #thermal-sensor-cells = <0>; + #io-channel-cells = <0>; + }; + +sun4i, sun5i and sun6i SoCs are also supported via the older binding: + +sun4i resistive touchscreen controller +-------------------------------------- + +Required properties: + - compatible: "allwinner,sun4i-a10-ts", "allwinner,sun5i-a13-ts" or + "allwinner,sun6i-a31-ts" + - reg: mmio address range of the chip + - interrupts: interrupt to which the chip is connected + - #thermal-sensor-cells: shall be 0 + +Optional properties: + - allwinner,ts-attached : boolean indicating that an actual touchscreen + is attached to the controller + - allwinner,tp-sensitive-adjust : integer (4 bits) + adjust sensitivity of pen down detection + between 0 (least sensitive) and 15 + (defaults to 15) + - allwinner,filter-type : integer (2 bits) + select median and averaging filter + samples used for median / averaging filter + 0: 4/2 + 1: 5/3 + 2: 8/4 + 3: 16/8 + (defaults to 1) + +Example: + + rtp: rtp@01c25000 { + compatible = "allwinner,sun4i-a10-ts"; + reg = <0x01c25000 0x100>; + interrupts = <29>; + allwinner,ts-attached; + #thermal-sensor-cells = <0>; + /* sensitive/noisy touch panel */ + allwinner,tp-sensitive-adjust = <0>; + allwinner,filter-type = <3>; + }; diff --git a/Documentation/devicetree/bindings/mfd/ti-lmu.txt b/Documentation/devicetree/bindings/mfd/ti-lmu.txt new file mode 100644 index 000000000000..c885cf89b8ce --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/ti-lmu.txt @@ -0,0 +1,243 @@ +TI LMU (Lighting Management Unit) device tree bindings + +TI LMU driver supports lighting devices below. + + Name Child nodes + ------ --------------------------------- + LM3532 Backlight + LM3631 Backlight and regulator + LM3632 Backlight and regulator + LM3633 Backlight, LED and fault monitor + LM3695 Backlight + LM3697 Backlight and fault monitor + +Required properties: + - compatible: Should be one of: + "ti,lm3532" + "ti,lm3631" + "ti,lm3632" + "ti,lm3633" + "ti,lm3695" + "ti,lm3697" + - reg: I2C slave address. + 0x11 for LM3632 + 0x29 for LM3631 + 0x36 for LM3633, LM3697 + 0x38 for LM3532 + 0x63 for LM3695 + +Optional property: + - enable-gpios: A GPIO specifier for hardware enable pin. + +Required node: + - backlight: All LMU devices have backlight child nodes. + For the properties, please refer to [1]. + +Optional nodes: + - fault-monitor: Hardware fault monitoring driver for LM3633 and LM3697. + Required properties: + - compatible: Should be one of: + "ti,lm3633-fault-monitor" + "ti,lm3697-fault-monitor" + - leds: LED properties for LM3633. Please refer to [2]. + - regulators: Regulator properties for LM3631 and LM3632. + Please refer to [3]. + +[1] ../leds/backlight/ti-lmu-backlight.txt +[2] ../leds/leds-lm3633.txt +[3] ../regulator/lm363x-regulator.txt + +lm3532@38 { + compatible = "ti,lm3532"; + reg = <0x38>; + + enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>; + + backlight { + compatible = "ti,lm3532-backlight"; + + lcd { + led-sources = <0 1 2>; + ramp-up-msec = <30>; + ramp-down-msec = <0>; + }; + }; +}; + +lm3631@29 { + compatible = "ti,lm3631"; + reg = <0x29>; + + regulators { + compatible = "ti,lm363x-regulator"; + + vboost { + regulator-name = "lcd_boost"; + regulator-min-microvolt = <4500000>; + regulator-max-microvolt = <6350000>; + regulator-always-on; + }; + + vcont { + regulator-name = "lcd_vcont"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + voref { + regulator-name = "lcd_voref"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6000000>; + }; + + vpos { + regulator-name = "lcd_vpos"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6000000>; + regulator-boot-on; + }; + + vneg { + regulator-name = "lcd_vneg"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6000000>; + regulator-boot-on; + }; + }; + + backlight { + compatible = "ti,lm3631-backlight"; + + lcd_bl { + led-sources = <0 1>; + ramp-up-msec = <300>; + }; + }; +}; + +lm3632@11 { + compatible = "ti,lm3632"; + reg = <0x11>; + + enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>; /* PC2 */ + + regulators { + compatible = "ti,lm363x-regulator"; + + ti,lcm-en1-gpio = <&pioC 0 GPIO_ACTIVE_HIGH>; /* PC0 */ + ti,lcm-en2-gpio = <&pioC 1 GPIO_ACTIVE_HIGH>; /* PC1 */ + + vboost { + regulator-name = "lcd_boost"; + regulator-min-microvolt = <4500000>; + regulator-max-microvolt = <6400000>; + regulator-always-on; + }; + + vpos { + regulator-name = "lcd_vpos"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6000000>; + }; + + vneg { + regulator-name = "lcd_vneg"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6000000>; + }; + }; + + backlight { + compatible = "ti,lm3632-backlight"; + + pwms = <&pwm0 0 10000 0>; /* pwm number, period, polarity */ + pwm-names = "lmu-backlight"; + + lcd { + led-sources = <0 1>; + pwm-period = <10000>; + }; + }; +}; + +lm3633@36 { + compatible = "ti,lm3633"; + reg = <0x36>; + + enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>; + + backlight { + compatible = "ti,lm3633-backlight"; + + main { + label = "main_lcd"; + led-sources = <1 2>; + ramp-up-msec = <500>; + ramp-down-msec = <500>; + }; + + front { + label = "front_lcd"; + led-sources = <0>; + ramp-up-msec = <1000>; + ramp-down-msec = <0>; + }; + }; + + leds { + compatible = "ti,lm3633-leds"; + + chan1 { + label = "status"; + led-sources = <1>; + led-max-microamp = <6000>; + }; + + chan345 { + label = "rgb"; + led-sources = <3 4 5>; + led-max-microamp = <10000>; + }; + }; + + fault-monitor { + compatible = "ti,lm3633-fault-monitor"; + }; +}; + +lm3695@63 { + compatible = "ti,lm3695"; + reg = <0x63>; + + enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>; + + backlight { + compatible = "ti,lm3695-backlight"; + + lcd { + label = "bl"; + led-sources = <0 1>; + }; + }; +}; + +lm3697@36 { + compatible = "ti,lm3697"; + reg = <0x36>; + + enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>; + + backlight { + compatible = "ti,lm3697-backlight"; + + lcd { + led-sources = <0 1 2>; + ramp-up-msec = <200>; + ramp-down-msec = <200>; + }; + }; + + fault-monitor { + compatible = "ti,lm3697-fault-monitor"; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/tps65086.txt b/Documentation/devicetree/bindings/mfd/tps65086.txt new file mode 100644 index 000000000000..9cfa886fe99f --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/tps65086.txt @@ -0,0 +1,55 @@ +* TPS65086 Power Management Integrated Circuit (PMIC) bindings + +Required properties: + - compatible : Should be "ti,tps65086". + - reg : I2C slave address. + - interrupt-parent : Phandle to the parent interrupt controller. + - interrupts : The interrupt line the device is connected to. + - interrupt-controller : Marks the device node as an interrupt controller. + - #interrupt-cells : The number of cells to describe an IRQ, should be 2. + The first cell is the IRQ number. + The second cell is the flags, encoded as trigger + masks from ../interrupt-controller/interrupts.txt. + - gpio-controller : Marks the device node as a GPIO Controller. + - #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify flags. + See ../gpio/gpio.txt for more information. + - regulators: : List of child nodes that specify the regulator + initialization data. Child nodes must be named + after their hardware counterparts: buck[1-6], + ldoa[1-3], swa1, swb[1-2], and vtt. Each child + node is defined using the standard binding for + regulators and the optional regulator properties + defined below. + +Optional regulator properties: + - ti,regulator-step-size-25mv : This is applicable for buck[1-6], set this + if the regulator is factory set with a 25mv + step voltage mapping. + - ti,regulator-decay : This is applicable for buck[1-6], set this if + the output needs to decay, default is for + the output to slew down. + +Example: + + pmic: tps65086@5e { + compatible = "ti,tps65086"; + reg = <0x5e>; + interrupt-parent = <&gpio1>; + interrupts = <28 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + + regulators { + buck1 { + regulator-name = "vcc1"; + regulator-min-microvolt = <1600000>; + regulator-max-microvolt = <1600000>; + regulator-boot-on; + ti,regulator-decay; + ti,regulator-step-size-25mv; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/tps65910.txt b/Documentation/devicetree/bindings/mfd/tps65910.txt index 38833e63a59f..8af1202b381d 100644 --- a/Documentation/devicetree/bindings/mfd/tps65910.txt +++ b/Documentation/devicetree/bindings/mfd/tps65910.txt @@ -61,6 +61,10 @@ Optional properties: There should be 9 entries here, one for each gpio. - ti,system-power-controller: Telling whether or not this pmic is controlling the system power. +- ti,sleep-enable: Enable SLEEP state. +- ti,sleep-keep-therm: Keep thermal monitoring on in sleep state. +- ti,sleep-keep-ck32k: Keep the 32KHz clock output on in sleep state. +- ti,sleep-keep-hsclk: Keep high speed internal clock on in sleep state. Regulator Optional properties: - ti,regulator-ext-sleep-control: enable external sleep diff --git a/Documentation/devicetree/bindings/mfd/tps65912.txt b/Documentation/devicetree/bindings/mfd/tps65912.txt new file mode 100644 index 000000000000..717e66d23142 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/tps65912.txt @@ -0,0 +1,50 @@ +* TPS65912 Power Management Integrated Circuit bindings + +Required properties: + - compatible : Should be "ti,tps65912". + - reg : Slave address or chip select number (I2C / SPI). + - interrupt-parent : The parent interrupt controller. + - interrupts : The interrupt line the device is connected to. + - interrupt-controller : Marks the device node as an interrupt controller. + - #interrupt-cells : The number of cells to describe an IRQ, should be 2. + The first cell is the IRQ number. + The second cell is the flags, encoded as trigger + masks from ../interrupt-controller/interrupts.txt. + - gpio-controller : Marks the device node as a GPIO Controller. + - #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify flags. + See ../gpio/gpio.txt for more information. + - regulators: : List of child nodes that specify the regulator + initialization data. Child nodes must be named + after their hardware counterparts: dcdc[1-4] and + ldo[1-10]. Each child nodes is defined using the + standard binding for regulators. + +Example: + + pmic: tps65912@2d { + compatible = "ti,tps65912"; + reg = <0x2d>; + interrupt-parent = <&gpio1>; + interrupts = <28 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + + regulators { + dcdc1 { + regulator-name = "vdd_core"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <1144000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <1900000>; + regulator-max-microvolt = <1900000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/twl6040.txt b/Documentation/devicetree/bindings/mfd/twl6040.txt index a41157b5d930..9a98ee7c323d 100644 --- a/Documentation/devicetree/bindings/mfd/twl6040.txt +++ b/Documentation/devicetree/bindings/mfd/twl6040.txt @@ -12,6 +12,7 @@ Required properties: - interrupt-parent: The parent interrupt controller - gpio-controller: - #gpio-cells = <1>: twl6040 provides GPO lines. +- #clock-cells = <0>; twl6040 is a provider of pdmclk which is used by McPDM - twl6040,audpwron-gpio: Power on GPIO line for the twl6040 - vio-supply: Regulator for the twl6040 VIO supply @@ -19,8 +20,8 @@ Required properties: Optional properties, nodes: - enable-active-high: To power on the twl6040 during boot. -- clocks: phandle to the clk32k clock provider -- clock-names: Must be "clk32k" +- clocks: phandle to the clk32k and/or to mclk clock provider +- clock-names: Must be "clk32k" for the 32K clock and "mclk" for the MCLK. Vibra functionality Required properties: diff --git a/Documentation/devicetree/bindings/mfd/wm831x.txt b/Documentation/devicetree/bindings/mfd/wm831x.txt new file mode 100644 index 000000000000..9f8b7430673c --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/wm831x.txt @@ -0,0 +1,81 @@ +Cirrus Logic/Wolfson Microelectronics wm831x PMICs + +System PMICs with a wide range of additional features. + +Required properties: + + - compatible : One of the following chip-specific strings: + "wlf,wm8310" + "wlf,wm8311" + "wlf,wm8312" + "wlf,wm8320" + "wlf,wm8321" + "wlf,wm8325" + "wlf,wm8326" + + - reg : I2C slave address when connected using I2C, chip select number + when using SPI. + + - gpio-controller : Indicates this device is a GPIO controller. + - #gpio-cells : Must be 2. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). + + - interrupts : The interrupt line the IRQ signal for the device is + connected to. + - interrupt-parent : The parent interrupt controller. + + - interrupt-controller : wm831x devices contain interrupt controllers and + may provide interrupt services to other devices. + - #interrupt-cells: Must be 2. The first cell is the IRQ number, and the + second cell is the flags, encoded as the trigger masks from + ../interrupt-controller/interrupts.txt + +Optional sub-nodes: + - regulators : Contains sub-nodes for each of the regulators supplied by + the device. The regulators are bound using their names listed below: + + dcdc1 : DCDC1 + dcdc2 : DCDC2 + dcdc3 : DCDC3 + dcdc4 : DCDC3 + isink1 : ISINK1 + isink2 : ISINK2 + ldo1 : LDO1 + ldo2 : LDO2 + ldo3 : LDO3 + ldo4 : LDO4 + ldo5 : LDO5 + ldo7 : LDO7 + ldo11 : LDO11 + + The bindings details of each regulator can be found in: + ../regulator/regulator.txt + +Example: + +wm8310: pmic@36 { + compatible = "wlf,wm8310"; + reg = <0x36>; + + gpio-controller; + #gpio-cells = <2>; + + interrupts = <347>; + interrupt-parent = <&gic>; + + interrupt-controller; + #interrupt-cells = <2>; + + regulators { + dcdc1: dcdc1 { + regulator-name = "DCDC1"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <600000>; + }; + ldo1: ldo1 { + regulator-name = "LDO1"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <1700000>; + }; + }; +}; |