1 files changed, 88 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/qca,qca7000.txt b/Documentation/devicetree/bindings/net/qca,qca7000.txt
new file mode 100644
index 000000000000..6d9efb2eb9a5
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/qca,qca7000.txt
@@ -0,0 +1,88 @@
+* Qualcomm QCA7000
+
+The QCA7000 is a serial-to-powerline bridge with a host interface which could
+be configured either as SPI or UART slave. This configuration is done by
+the QCA7000 firmware.
+
+(a) Ethernet over SPI
+
+In order to use the QCA7000 as SPI device it must be defined as a child of a
+SPI master in the device tree.
+
+Required properties:
+- compatible	    : Should be "qca,qca7000"
+- reg		    : Should specify the SPI chip select
+- interrupts	    : The first cell should specify the index of the source
+		      interrupt and the second cell should specify the trigger
+		      type as rising edge
+- spi-cpha	    : Must be set
+- spi-cpol	    : Must be set
+
+Optional properties:
+- interrupt-parent  : Specify the pHandle of the source interrupt
+- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at.
+		      Numbers smaller than 1000000 or greater than 16000000
+		      are invalid. Missing the property will set the SPI
+		      frequency to 8000000 Hertz.
+- local-mac-address : see ./ethernet.txt
+- qca,legacy-mode   : Set the SPI data transfer of the QCA7000 to legacy mode.
+		      In this mode the SPI master must toggle the chip select
+		      between each data word. In burst mode these gaps aren't
+		      necessary, which is faster. This setting depends on how
+		      the QCA7000 is setup via GPIO pin strapping. If the
+		      property is missing the driver defaults to burst mode.
+
+SPI Example:
+
+/* Freescale i.MX28 SPI master*/
+ssp2: spi@80014000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+
+	qca7000: ethernet@0 {
+		compatible = "qca,qca7000";
+		reg = <0x0>;
+		interrupt-parent = <&gpio3>;      /* GPIO Bank 3 */
+		interrupts = <25 0x1>;            /* Index: 25, rising edge */
+		spi-cpha;                         /* SPI mode: CPHA=1 */
+		spi-cpol;                         /* SPI mode: CPOL=1 */
+		spi-max-frequency = <8000000>;    /* freq: 8 MHz */
+		local-mac-address = [ A0 B0 C0 D0 E0 F0 ];
+	};
+};
+
+(b) Ethernet over UART
+
+In order to use the QCA7000 as UART slave it must be defined as a child of a
+UART master in the device tree. It is possible to preconfigure the UART
+settings of the QCA7000 firmware, but it's not possible to change them during
+runtime.
+
+Required properties:
+- compatible        : Should be "qca,qca7000"
+
+Optional properties:
+- local-mac-address : see ./ethernet.txt
+- current-speed     : current baud rate of QCA7000 which defaults to 115200
+		      if absent, see also ../serial/slave-device.txt
+
+UART Example:
+
+/* Freescale i.MX28 UART */
+auart0: serial@8006a000 {
+	compatible = "fsl,imx28-auart", "fsl,imx23-auart";
+	reg = <0x8006a000 0x2000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_2pins_a>;
+	status = "okay";
+
+	qca7000: ethernet {
+		compatible = "qca,qca7000";
+		local-mac-address = [ A0 B0 C0 D0 E0 F0 ];
+		current-speed = <38400>;
+	};
+};