diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/wireless')
8 files changed, 329 insertions, 8 deletions
diff --git a/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt b/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt index 5dbf169cd81c..590f622188de 100644 --- a/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt +++ b/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt @@ -31,7 +31,7 @@ mmc3: mmc@01c12000 { non-removable; status = "okay"; - brcmf: bcrmf@1 { + brcmf: wifi@1 { reg = <1>; compatible = "brcm,bcm4329-fmac"; interrupt-parent = <&pio>; diff --git a/Documentation/devicetree/bindings/net/wireless/esp,esp8089.txt b/Documentation/devicetree/bindings/net/wireless/esp,esp8089.txt new file mode 100644 index 000000000000..19331bb4ff6e --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/esp,esp8089.txt @@ -0,0 +1,31 @@ +Espressif ESP8089 wireless SDIO devices + +This node provides properties for controlling the ESP8089 wireless device. +The node is expected to be specified as a child node to the SDIO controller +that connects the device to the system. + +Required properties: + + - compatible : Should be "esp,esp8089". + +Optional properties: + - esp,crystal-26M-en: Integer value for the crystal_26M_en firmware parameter + +Example: + +&mmc1 { + #address-cells = <1>; + #size-cells = <0>; + + vmmc-supply = <®_dldo1>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + esp8089: sdio_wifi@1 { + compatible = "esp,esp8089"; + reg = <1>; + esp,crystal-26M-en = <2>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/ieee80211.txt b/Documentation/devicetree/bindings/net/wireless/ieee80211.txt new file mode 100644 index 000000000000..f6442b1397f5 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/ieee80211.txt @@ -0,0 +1,24 @@ +Common IEEE 802.11 properties + +This provides documentation of common properties that are valid for all wireless +devices. + +Optional properties: + - ieee80211-freq-limit : list of supported frequency ranges in KHz. This can be + used for devices that in a given config support less channels than + normally. It may happen chipset supports a wide wireless band but it is + limited to some part of it due to used antennas or power amplifier. + An example case for this can be tri-band wireless router with two + identical chipsets used for two different 5 GHz subbands. Using them + incorrectly could not work or decrease performance noticeably. + +Example: + +pcie@0,0 { + reg = <0x0000 0 0 0 0>; + wifi@0,0 { + reg = <0x0000 0 0 0 0>; + ieee80211-freq-limit = <2402000 2482000>, + <5170000 5250000>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt b/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt new file mode 100644 index 000000000000..0854451ff91d --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt @@ -0,0 +1,70 @@ +Marvell 8787/8897/8997 (sd8787/sd8897/sd8997/pcie8997) SDIO/PCIE devices +------ + +This node provides properties for controlling the Marvell SDIO/PCIE wireless device. +The node is expected to be specified as a child node to the SDIO/PCIE controller that +connects the device to the system. + +Required properties: + + - compatible : should be one of the following: + * "marvell,sd8787" + * "marvell,sd8897" + * "marvell,sd8997" + * "pci11ab,2b42" + * "pci1b4b,2b42" + +Optional properties: + + - marvell,caldata* : A series of properties with marvell,caldata prefix, + represent calibration data downloaded to the device during + initialization. This is an array of unsigned 8-bit values. + the properties should follow below property name and + corresponding array length: + "marvell,caldata-txpwrlimit-2g" (length = 566). + "marvell,caldata-txpwrlimit-5g-sub0" (length = 502). + "marvell,caldata-txpwrlimit-5g-sub1" (length = 688). + "marvell,caldata-txpwrlimit-5g-sub2" (length = 750). + "marvell,caldata-txpwrlimit-5g-sub3" (length = 502). + - marvell,wakeup-pin : a wakeup pin number of wifi chip which will be configured + to firmware. Firmware will wakeup the host using this pin + during suspend/resume. + - interrupt-parent: phandle of the parent interrupt controller + - interrupts : interrupt pin number to the cpu. driver will request an irq based on + this interrupt number. during system suspend, the irq will be enabled + so that the wifi chip can wakeup host platform under certain condition. + during system resume, the irq will be disabled to make sure + unnecessary interrupt is not received. + - vmmc-supply: a phandle of a regulator, supplying VCC to the card + - mmc-pwrseq: phandle to the MMC power sequence node. See "mmc-pwrseq-*" + for documentation of MMC power sequence bindings. + +Example: + +Tx power limit calibration data is configured in below example. +The calibration data is an array of unsigned values, the length +can vary between hw versions. +IRQ pin 38 is used as system wakeup source interrupt. wakeup pin 3 is configured +so that firmware can wakeup host using this device side pin. + +&mmc3 { + status = "okay"; + vmmc-supply = <&wlan_en_reg>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + cap-power-off-card; + keep-power-in-suspend; + + #address-cells = <1>; + #size-cells = <0>; + mwifiex: wifi@1 { + compatible = "marvell,sd8897"; + reg = <1>; + interrupt-parent = <&pio>; + interrupts = <38 IRQ_TYPE_LEVEL_LOW>; + + marvell,caldata_00_txpwrlimit_2g_cfg_set = /bits/ 8 < + 0x01 0x00 0x06 0x00 0x08 0x02 0x89 0x01>; + marvell,wakeup-pin = <3>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt b/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt new file mode 100644 index 000000000000..b7396c8c271c --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt @@ -0,0 +1,48 @@ +* Qualcomm Atheros ath9k wireless devices + +This node provides properties for configuring the ath9k wireless device. The +node is expected to be specified as a child node of the PCI controller to +which the wireless chip is connected. + +Required properties: +- compatible: For PCI and PCIe devices this should be an identifier following + the format as defined in "PCI Bus Binding to Open Firmware" + Revision 2.1. One of the possible formats is "pciVVVV,DDDD" + where VVVV is the PCI vendor ID and DDDD is PCI device ID. + Typically QCA's PCI vendor ID 168c is used while the PCI device + ID depends on the chipset - see the following (possibly + incomplete) list: + - 0023 for AR5416 + - 0024 for AR5418 + - 0027 for AR9160 + - 0029 for AR9220 and AR9223 + - 002a for AR9280 and AR9283 + - 002b for AR9285 + - 002c for AR2427 + - 002d for AR9227 + - 002e for AR9287 + - 0030 for AR9380, AR9381 and AR9382 + - 0032 for AR9485 + - 0033 for AR9580 and AR9590 + - 0034 for AR9462 + - 0036 for AR9565 + - 0037 for AR9485 +- reg: Address and length of the register set for the device. + +Optional properties: +- qca,no-eeprom: Indicates that there is no physical EEPROM connected to the + ath9k wireless chip (in this case the calibration / + EEPROM data will be loaded from userspace using the + kernel firmware loader). +- mac-address: See ethernet.txt in the parent directory +- local-mac-address: See ethernet.txt in the parent directory + + +In this example, the node is defined as child node of the PCI controller: +&pci0 { + wifi@168c,002d { + compatible = "pci168c,002d"; + reg = <0x7000 0 0 0 0x1000>; + qca,no-eeprom; + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt index edefc26c6204..74d7f0af209c 100644 --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt @@ -1,17 +1,55 @@ * Qualcomm Atheros ath10k wireless devices -For ath10k devices the calibration data can be provided through Device -Tree. The node is a child node of the PCI controller. - Required properties: --compatible : Should be "qcom,ath10k" +- compatible: Should be one of the following: + * "qcom,ath10k" + * "qcom,ipq4019-wifi" + +PCI based devices uses compatible string "qcom,ath10k" and takes calibration +data along with board specific data via "qcom,ath10k-calibration-data". +Rest of the properties are not applicable for PCI based devices. + +AHB based devices (i.e. ipq4019) uses compatible string "qcom,ipq4019-wifi" +and also uses most of the properties defined in this doc (except +"qcom,ath10k-calibration-data"). It uses "qcom,ath10k-pre-calibration-data" +to carry pre calibration data. + +In general, entry "qcom,ath10k-pre-calibration-data" and +"qcom,ath10k-calibration-data" conflict with each other and only one +can be provided per device. Optional properties: -- qcom,ath10k-calibration-data : calibration data as an array, the - length can vary between hw versions +- reg: Address and length of the register set for the device. +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reseti.txt for details. +- reset-names: Must include the list of following reset names, + "wifi_cpu_init" + "wifi_radio_srif" + "wifi_radio_warm" + "wifi_radio_cold" + "wifi_core_warm" + "wifi_core_cold" +- clocks: List of clock specifiers, must contain an entry for each required + entry in clock-names. +- clock-names: Should contain the clock names "wifi_wcss_cmd", "wifi_wcss_ref", + "wifi_wcss_rtc". +- interrupts: List of interrupt lines. Must contain an entry + for each entry in the interrupt-names property. +- interrupt-names: Must include the entries for MSI interrupt + names ("msi0" to "msi15") and legacy interrupt + name ("legacy"), +- qcom,msi_addr: MSI interrupt address. +- qcom,msi_base: Base value to add before writing MSI data into + MSI address register. +- qcom,ath10k-calibration-data : calibration data + board specific data + as an array, the length can vary between + hw versions. +- qcom,ath10k-pre-calibration-data : pre calibration data as an array, + the length can vary between hw versions. +Example (to supply the calibration data alone): -Example: +In this example, the node is defined as child node of the PCI controller. pci { pcie@0 { @@ -28,3 +66,53 @@ pci { }; }; }; + +Example (to supply ipq4019 SoC wifi block details): + +wifi0: wifi@a000000 { + compatible = "qcom,ipq4019-wifi"; + reg = <0xa000000 0x200000>; + resets = <&gcc WIFI0_CPU_INIT_RESET>, + <&gcc WIFI0_RADIO_SRIF_RESET>, + <&gcc WIFI0_RADIO_WARM_RESET>, + <&gcc WIFI0_RADIO_COLD_RESET>, + <&gcc WIFI0_CORE_WARM_RESET>, + <&gcc WIFI0_CORE_COLD_RESET>; + reset-names = "wifi_cpu_init", + "wifi_radio_srif", + "wifi_radio_warm", + "wifi_radio_cold", + "wifi_core_warm", + "wifi_core_cold"; + clocks = <&gcc GCC_WCSS2G_CLK>, + <&gcc GCC_WCSS2G_REF_CLK>, + <&gcc GCC_WCSS2G_RTC_CLK>; + clock-names = "wifi_wcss_cmd", + "wifi_wcss_ref", + "wifi_wcss_rtc"; + interrupts = <0 0x20 0x1>, + <0 0x21 0x1>, + <0 0x22 0x1>, + <0 0x23 0x1>, + <0 0x24 0x1>, + <0 0x25 0x1>, + <0 0x26 0x1>, + <0 0x27 0x1>, + <0 0x28 0x1>, + <0 0x29 0x1>, + <0 0x2a 0x1>, + <0 0x2b 0x1>, + <0 0x2c 0x1>, + <0 0x2d 0x1>, + <0 0x2e 0x1>, + <0 0x2f 0x1>, + <0 0xa8 0x0>; + interrupt-names = "msi0", "msi1", "msi2", "msi3", + "msi4", "msi5", "msi6", "msi7", + "msi8", "msi9", "msi10", "msi11", + "msi12", "msi13", "msi14", "msi15", + "legacy"; + qcom,msi_addr = <0x0b006040>; + qcom,msi_base = <0x40>; + qcom,ath10k-pre-calibration-data = [ 01 02 03 ... ]; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt new file mode 100644 index 000000000000..8f9ced076fe1 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt @@ -0,0 +1,59 @@ +* Texas Instruments wl12xx/wl18xx wireless lan controller + +The wl12xx/wl18xx chips can be connected via SPI or via SDIO. This +document describes the binding for the SPI connected chip. + +Required properties: +- compatible : Should be one of the following: + * "ti,wl1271" + * "ti,wl1273" + * "ti,wl1281" + * "ti,wl1283" + * "ti,wl1801" + * "ti,wl1805" + * "ti,wl1807" + * "ti,wl1831" + * "ti,wl1835" + * "ti,wl1837" +- reg : Chip select address of device +- spi-max-frequency : Maximum SPI clocking speed of device in Hz +- interrupt-parent, interrupts : + Should contain parameters for 1 interrupt line. + Interrupt parameters: parent, line number, type. +- vwlan-supply : Point the node of the regulator that powers/enable the + wl12xx/wl18xx chip + +Optional properties: +- ref-clock-frequency : Reference clock frequency (should be set for wl12xx) +- clock-xtal : boolean, clock is generated from XTAL + +- Please consult Documentation/devicetree/bindings/spi/spi-bus.txt + for optional SPI connection related properties, + +Examples: + +For wl12xx family: +&spi1 { + wlcore: wlcore@1 { + compatible = "ti,wl1271"; + reg = <1>; + spi-max-frequency = <48000000>; + interrupt-parent = <&gpio3>; + interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; + vwlan-supply = <&vwlan_fixed>; + clock-xtal; + ref-clock-frequency = <38400000>; + }; +}; + +For wl18xx family: +&spi0 { + wlcore: wlcore@0 { + compatible = "ti,wl1835"; + reg = <0>; + spi-max-frequency = <48000000>; + interrupt-parent = <&gpio0>; + interrupts = <27 IRQ_TYPE_EDGE_RISING>; + vwlan-supply = <&vwlan_fixed>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt index 2a3d90de18ee..7b2cbb14113e 100644 --- a/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt +++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt @@ -10,6 +10,7 @@ Required properties: * "ti,wl1273" * "ti,wl1281" * "ti,wl1283" + * "ti,wl1285" * "ti,wl1801" * "ti,wl1805" * "ti,wl1807" |