diff options
Diffstat (limited to 'Documentation/devicetree/bindings/phy')
30 files changed, 1767 insertions, 49 deletions
diff --git a/Documentation/devicetree/bindings/phy/bcm-ns-usb2-phy.txt b/Documentation/devicetree/bindings/phy/bcm-ns-usb2-phy.txt new file mode 100644 index 000000000000..a7aee9ea8926 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/bcm-ns-usb2-phy.txt @@ -0,0 +1,21 @@ +Driver for Broadcom Northstar USB 2.0 PHY + +Required properties: +- compatible: brcm,ns-usb2-phy +- reg: iomem address range of DMU (Device Management Unit) +- reg-names: "dmu", the only needed & supported reg right now +- clocks: USB PHY reference clock +- clock-names: "phy-ref-clk", the only needed & supported clock right now + +To initialize USB 2.0 PHY driver needs to setup PLL correctly. To do this it +requires passing phandle to the USB PHY reference clock. + +Example: + usb2-phy { + compatible = "brcm,ns-usb2-phy"; + reg = <0x1800c000 0x1000>; + reg-names = "dmu"; + #phy-cells = <0>; + clocks = <&genpll BCM_NSP_GENPLL_USB_PHY_REF_CLK>; + clock-names = "phy-ref-clk"; + }; diff --git a/Documentation/devicetree/bindings/phy/bcm-ns-usb3-phy.txt b/Documentation/devicetree/bindings/phy/bcm-ns-usb3-phy.txt new file mode 100644 index 000000000000..32f057260351 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/bcm-ns-usb3-phy.txt @@ -0,0 +1,34 @@ +Driver for Broadcom Northstar USB 3.0 PHY + +Required properties: + +- compatible: one of: "brcm,ns-ax-usb3-phy", "brcm,ns-bx-usb3-phy". +- reg: address of MDIO bus device +- usb3-dmp-syscon: phandle to syscon with DMP (Device Management Plugin) + registers +- #phy-cells: must be 0 + +Initialization of USB 3.0 PHY depends on Northstar version. There are currently +three known series: Ax, Bx and Cx. +Known A0: BCM4707 rev 0 +Known B0: BCM4707 rev 4, BCM53573 rev 2 +Known B1: BCM4707 rev 6 +Known C0: BCM47094 rev 0 + +Example: + mdio: mdio@0 { + reg = <0x0>; + #size-cells = <1>; + #address-cells = <0>; + + usb3-phy@10 { + compatible = "brcm,ns-ax-usb3-phy"; + reg = <0x10>; + usb3-dmp-syscon = <&usb3_dmp>; + #phy-cells = <0>; + }; + }; + + usb3_dmp: syscon@18105000 { + reg = <0x18105000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/phy/brcm,mdio-mux-bus-pci.txt b/Documentation/devicetree/bindings/phy/brcm,mdio-mux-bus-pci.txt new file mode 100644 index 000000000000..5b51007c6f24 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/brcm,mdio-mux-bus-pci.txt @@ -0,0 +1,27 @@ +* Broadcom NS2 PCIe PHY binding document + +Required bus properties: +- reg: MDIO Bus number for the MDIO interface +- #address-cells: must be 1 +- #size-cells: must be 0 + +Required PHY properties: +- compatible: should be "brcm,ns2-pcie-phy" +- reg: MDIO Phy ID for the MDIO interface +- #phy-cells: must be 0 + +This is a child bus node of "brcm,mdio-mux-iproc" node. + +Example: + +mdio@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + + pci_phy0: pci-phy@0 { + compatible = "brcm,ns2-pcie-phy"; + reg = <0x0>; + #phy-cells = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt b/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt new file mode 100644 index 000000000000..04f063aa7883 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt @@ -0,0 +1,30 @@ +BROADCOM NORTHSTAR2 USB2 (DUAL ROLE DEVICE) PHY + +Required properties: + - compatible: brcm,ns2-drd-phy + - reg: offset and length of the NS2 PHY related registers. + - reg-names + The below registers must be provided. + icfg - for DRD ICFG configurations + rst-ctrl - for DRD IDM reset + crmu-ctrl - for CRMU core vdd, PHY and PHY PLL reset + usb2-strap - for port over current polarity reversal + - #phy-cells: Must be 0. No args required. + - vbus-gpios: vbus gpio binding + - id-gpios: id gpio binding + +Refer to phy/phy-bindings.txt for the generic PHY binding properties + +Example: + usbdrd_phy: phy@66000960 { + #phy-cells = <0>; + compatible = "brcm,ns2-drd-phy"; + reg = <0x66000960 0x24>, + <0x67012800 0x4>, + <0x6501d148 0x4>, + <0x664d0700 0x4>; + reg-names = "icfg", "rst-ctrl", + "crmu-ctrl", "usb2-strap"; + id-gpios = <&gpio_g 30 0>; + vbus-gpios = <&gpio_g 31 0>; + }; diff --git a/Documentation/devicetree/bindings/phy/brcm,brcmstb-sata-phy.txt b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt index d87ab7c127b8..97977cd29a98 100644 --- a/Documentation/devicetree/bindings/phy/brcm,brcmstb-sata-phy.txt +++ b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt @@ -1,14 +1,19 @@ -* Broadcom SATA3 PHY for STB +* Broadcom SATA3 PHY Required properties: - compatible: should be one or more of "brcm,bcm7425-sata-phy" "brcm,bcm7445-sata-phy" + "brcm,iproc-ns2-sata-phy" + "brcm,iproc-nsp-sata-phy" "brcm,phy-sata3" + "brcm,iproc-sr-sata-phy" - address-cells: should be 1 - size-cells: should be 0 -- reg: register range for the PHY PCB interface -- reg-names: should be "phy" +- reg: register ranges for the PHY PCB interface +- reg-names: should be "phy" and "phy-ctrl" + The "phy-ctrl" registers are only required for + "brcm,iproc-ns2-sata-phy" and "brcm,iproc-sr-sata-phy". Sub-nodes: Each port's PHY should be represented as a sub-node. @@ -16,12 +21,13 @@ Sub-nodes: Sub-nodes required properties: - reg: the PHY number - phy-cells: generic PHY binding; must be 0 -Optional: -- brcm,enable-ssc: use spread spectrum clocking (SSC) on this port +Sub-nodes optional properties: +- brcm,enable-ssc: use spread spectrum clocking (SSC) on this port + This property is not applicable for "brcm,iproc-ns2-sata-phy", + "brcm,iproc-nsp-sata-phy" and "brcm,iproc-sr-sata-phy". Example: - sata-phy@f0458100 { compatible = "brcm,bcm7445-sata-phy", "brcm,phy-sata3"; reg = <0xf0458100 0x1e00>, <0xf045804c 0x10>; diff --git a/Documentation/devicetree/bindings/phy/meson-gxl-usb2-phy.txt b/Documentation/devicetree/bindings/phy/meson-gxl-usb2-phy.txt new file mode 100644 index 000000000000..a105494a0fc9 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/meson-gxl-usb2-phy.txt @@ -0,0 +1,17 @@ +* Amlogic Meson GXL and GXM USB2 PHY binding + +Required properties: +- compatible: Should be "amlogic,meson-gxl-usb2-phy" +- reg: The base address and length of the registers +- #phys-cells: must be 0 (see phy-bindings.txt in this directory) + +Optional properties: +- phy-supply: see phy-bindings.txt in this directory + + +Example: + usb2_phy0: phy@78000 { + compatible = "amlogic,meson-gxl-usb2-phy"; + #phy-cells = <0>; + reg = <0x0 0x78000 0x0 0x20>; + }; diff --git a/Documentation/devicetree/bindings/phy/meson8b-usb2-phy.txt b/Documentation/devicetree/bindings/phy/meson8b-usb2-phy.txt new file mode 100644 index 000000000000..d81d73aea608 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/meson8b-usb2-phy.txt @@ -0,0 +1,28 @@ +* Amlogic Meson8, Meson8b and GXBB USB2 PHY + +Required properties: +- compatible: Depending on the platform this should be one of: + "amlogic,meson8-usb2-phy" + "amlogic,meson8b-usb2-phy" + "amlogic,meson-gxbb-usb2-phy" +- reg: The base address and length of the registers +- #phys-cells: should be 0 (see phy-bindings.txt in this directory) +- clocks: phandle and clock identifier for the phy clocks +- clock-names: "usb_general" and "usb" + +Optional properties: +- resets: reference to the reset controller +- phy-supply: see phy-bindings.txt in this directory + + +Example: + +usb0_phy: usb-phy@c0000000 { + compatible = "amlogic,meson-gxbb-usb2-phy"; + #phy-cells = <0>; + reg = <0x0 0xc0000000 0x0 0x20>; + resets = <&reset RESET_USB_OTG>; + clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB0>; + clock-names = "usb_general", "usb"; + phy-supply = <&usb_vbus>; +}; diff --git a/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt b/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt index 379b84a567cc..1d25b04cd05e 100644 --- a/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt @@ -12,6 +12,16 @@ Required properties: - interrupts: Should contain phy interrupt - fsl,anatop: phandle for anatop register, it is only for imx6 SoC series +Optional properties: +- fsl,tx-cal-45-dn-ohms: Integer [30-55]. Resistance (in ohms) of switchable + high-speed trimming resistor connected in parallel with the 45 ohm resistor + that terminates the DN output signal. Default: 45 +- fsl,tx-cal-45-dp-ohms: Integer [30-55]. Resistance (in ohms) of switchable + high-speed trimming resistor connected in parallel with the 45 ohm resistor + that terminates the DP output signal. Default: 45 +- fsl,tx-d-cal: Integer [79-119]. Current trimming value (as a percentage) of + the 17.78mA TX reference current. Default: 100 + Example: usbphy1: usbphy@020c9000 { compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy"; diff --git a/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt new file mode 100644 index 000000000000..3742c152c467 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt @@ -0,0 +1,733 @@ +Device tree binding for NVIDIA Tegra XUSB pad controller +======================================================== + +The Tegra XUSB pad controller manages a set of I/O lanes (with differential +signals) which connect directly to pins/pads on the SoC package. Each lane +is controlled by a HW block referred to as a "pad" in the Tegra hardware +documentation. Each such "pad" may control either one or multiple lanes, +and thus contains any logic common to all its lanes. Each lane can be +separately configured and powered up. + +Some of the lanes are high-speed lanes, which can be used for PCIe, SATA or +super-speed USB. Other lanes are for various types of low-speed, full-speed +or high-speed USB (such as UTMI, ULPI and HSIC). The XUSB pad controller +contains a software-configurable mux that sits between the I/O controller +ports (e.g. PCIe) and the lanes. + +In addition to per-lane configuration, USB 3.0 ports may require additional +settings on a per-board basis. + +Pads will be represented as children of the top-level XUSB pad controller +device tree node. Each lane exposed by the pad will be represented by its +own subnode and can be referenced by users of the lane using the standard +PHY bindings, as described by the phy-bindings.txt file in this directory. + +The Tegra hardware documentation refers to the connection between the XUSB +pad controller and the XUSB controller as "ports". This is confusing since +"port" is typically used to denote the physical USB receptacle. The device +tree binding in this document uses the term "port" to refer to the logical +abstraction of the signals that are routed to a USB receptacle (i.e. a PHY +for the USB signal, the VBUS power supply, the USB 2.0 companion port for +USB 3.0 receptacles, ...). + +Required properties: +-------------------- +- compatible: Must be: + - Tegra124: "nvidia,tegra124-xusb-padctl" + - Tegra132: "nvidia,tegra132-xusb-padctl", "nvidia,tegra124-xusb-padctl" + - Tegra210: "nvidia,tegra210-xusb-padctl" +- reg: Physical base address and length of the controller's registers. +- resets: Must contain an entry for each entry in reset-names. +- reset-names: Must include the following entries: + - "padctl" + + +Pad nodes: +========== + +A required child node named "pads" contains a list of subnodes, one for each +of the pads exposed by the XUSB pad controller. Each pad may need additional +resources that can be referenced in its pad node. + +The "status" property is used to enable or disable the use of a pad. If set +to "disabled", the pad will not be used on the given board. In order to use +the pad and any of its lanes, this property must be set to "okay". + +For Tegra124 and Tegra132, the following pads exist: usb2, ulpi, hsic, pcie +and sata. No extra resources are required for operation of these pads. + +For Tegra210, the following pads exist: usb2, hsic, pcie and sata. Below is +a description of the properties of each pad. + +UTMI pad: +--------- + +Required properties: +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Must contain the following entries: + - "trk": phandle and specifier referring to the USB2 tracking clock + +HSIC pad: +--------- + +Required properties: +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Must contain the following entries: + - "trk": phandle and specifier referring to the HSIC tracking clock + +PCIe pad: +--------- + +Required properties: +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Must contain the following entries: + - "pll": phandle and specifier referring to the PLLE +- resets: Must contain an entry for each entry in reset-names. +- reset-names: Must contain the following entries: + - "phy": reset for the PCIe UPHY block + +SATA pad: +--------- + +Required properties: +- resets: Must contain an entry for each entry in reset-names. +- reset-names: Must contain the following entries: + - "phy": reset for the SATA UPHY block + + +PHY nodes: +========== + +Each pad node has a child named "lanes" that contains one or more children of +its own, each representing one of the lanes controlled by the pad. + +Required properties: +-------------------- +- status: Defines the operation status of the PHY. Valid values are: + - "disabled": the PHY is disabled + - "okay": the PHY is enabled +- #phy-cells: Should be 0. Since each lane represents a single PHY, there is + no need for an additional specifier. +- nvidia,function: The output function of the PHY. See below for a list of + valid functions per SoC generation. + +For Tegra124 and Tegra132, the list of valid PHY nodes is given below: +- usb2: usb2-0, usb2-1, usb2-2 + - functions: "snps", "xusb", "uart" +- ulpi: ulpi-0 + - functions: "snps", "xusb" +- hsic: hsic-0, hsic-1 + - functions: "snps", "xusb" +- pcie: pcie-0, pcie-1, pcie-2, pcie-3, pcie-4 + - functions: "pcie", "usb3-ss" +- sata: sata-0 + - functions: "usb3-ss", "sata" + +For Tegra210, the list of valid PHY nodes is given below: +- usb2: usb2-0, usb2-1, usb2-2, usb2-3 + - functions: "snps", "xusb", "uart" +- hsic: hsic-0, hsic-1 + - functions: "snps", "xusb" +- pcie: pcie-0, pcie-1, pcie-2, pcie-3, pcie-4, pcie-5, pcie-6 + - functions: "pcie-x1", "usb3-ss", "pcie-x4" +- sata: sata-0 + - functions: "usb3-ss", "sata" + + +Port nodes: +=========== + +A required child node named "ports" contains a list of all the ports exposed +by the XUSB pad controller. Per-port configuration is only required for USB. + +USB2 ports: +----------- + +Required properties: +- status: Defines the operation status of the port. Valid values are: + - "disabled": the port is disabled + - "okay": the port is enabled +- mode: A string that determines the mode in which to run the port. Valid + values are: + - "host": for USB host mode + - "device": for USB device mode + - "otg": for USB OTG mode + +Optional properties: +- nvidia,internal: A boolean property whose presence determines that a port + is internal. In the absence of this property the port is considered to be + external. +- vbus-supply: phandle to a regulator supplying the VBUS voltage. + +ULPI ports: +----------- + +Optional properties: +- status: Defines the operation status of the port. Valid values are: + - "disabled": the port is disabled + - "okay": the port is enabled +- nvidia,internal: A boolean property whose presence determines that a port + is internal. In the absence of this property the port is considered to be + external. +- vbus-supply: phandle to a regulator supplying the VBUS voltage. + +HSIC ports: +----------- + +Required properties: +- status: Defines the operation status of the port. Valid values are: + - "disabled": the port is disabled + - "okay": the port is enabled + +Optional properties: +- vbus-supply: phandle to a regulator supplying the VBUS voltage. + +Super-speed USB ports: +---------------------- + +Required properties: +- status: Defines the operation status of the port. Valid values are: + - "disabled": the port is disabled + - "okay": the port is enabled +- nvidia,usb2-companion: A single cell that specifies the physical port number + to map this super-speed USB port to. The range of valid port numbers varies + with the SoC generation: + - 0-2: for Tegra124 and Tegra132 + - 0-3: for Tegra210 + +Optional properties: +- nvidia,internal: A boolean property whose presence determines that a port + is internal. In the absence of this property the port is considered to be + external. + +For Tegra124 and Tegra132, the XUSB pad controller exposes the following +ports: +- 3x USB2: usb2-0, usb2-1, usb2-2 +- 1x ULPI: ulpi-0 +- 2x HSIC: hsic-0, hsic-1 +- 2x super-speed USB: usb3-0, usb3-1 + +For Tegra210, the XUSB pad controller exposes the following ports: +- 4x USB2: usb2-0, usb2-1, usb2-2, usb2-3 +- 2x HSIC: hsic-0, hsic-1 +- 4x super-speed USB: usb3-0, usb3-1, usb3-2, usb3-3 + + +Examples: +========= + +Tegra124 and Tegra132: +---------------------- + +SoC include: + + padctl@7009f000 { + /* for Tegra124 */ + compatible = "nvidia,tegra124-xusb-padctl"; + /* for Tegra132 */ + compatible = "nvidia,tegra132-xusb-padctl", + "nvidia,tegra124-xusb-padctl"; + reg = <0x0 0x7009f000 0x0 0x1000>; + resets = <&tegra_car 142>; + reset-names = "padctl"; + + pads { + usb2 { + status = "disabled"; + + lanes { + usb2-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-1 { + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-2 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + ulpi { + status = "disabled"; + + lanes { + ulpi-0 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + hsic { + status = "disabled"; + + lanes { + hsic-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + hsic-1 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + pcie { + status = "disabled"; + + lanes { + pcie-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-1 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-2 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-3 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-4 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + sata { + status = "disabled"; + + lanes { + sata-0 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + }; + + ports { + usb2-0 { + status = "disabled"; + }; + + usb2-1 { + status = "disabled"; + }; + + usb2-2 { + status = "disabled"; + }; + + ulpi-0 { + status = "disabled"; + }; + + hsic-0 { + status = "disabled"; + }; + + hsic-1 { + status = "disabled"; + }; + + usb3-0 { + status = "disabled"; + }; + + usb3-1 { + status = "disabled"; + }; + }; + }; + +Board file: + + padctl@7009f000 { + status = "okay"; + + pads { + usb2 { + status = "okay"; + + lanes { + usb2-0 { + nvidia,function = "xusb"; + status = "okay"; + }; + + usb2-1 { + nvidia,function = "xusb"; + status = "okay"; + }; + + usb2-2 { + nvidia,function = "xusb"; + status = "okay"; + }; + }; + }; + + pcie { + status = "okay"; + + lanes { + pcie-0 { + nvidia,function = "usb3-ss"; + status = "okay"; + }; + + pcie-2 { + nvidia,function = "pcie"; + status = "okay"; + }; + + pcie-4 { + nvidia,function = "pcie"; + status = "okay"; + }; + }; + }; + + sata { + status = "okay"; + + lanes { + sata-0 { + nvidia,function = "sata"; + status = "okay"; + }; + }; + }; + }; + + ports { + /* Micro A/B */ + usb2-0 { + status = "okay"; + mode = "otg"; + }; + + /* Mini PCIe */ + usb2-1 { + status = "okay"; + mode = "host"; + }; + + /* USB3 */ + usb2-2 { + status = "okay"; + mode = "host"; + + vbus-supply = <&vdd_usb3_vbus>; + }; + + usb3-0 { + nvidia,port = <2>; + status = "okay"; + }; + }; + }; + +Tegra210: +--------- + +SoC include: + + padctl@7009f000 { + compatible = "nvidia,tegra210-xusb-padctl"; + reg = <0x0 0x7009f000 0x0 0x1000>; + resets = <&tegra_car 142>; + reset-names = "padctl"; + + status = "disabled"; + + pads { + usb2 { + clocks = <&tegra_car TEGRA210_CLK_USB2_TRK>; + clock-names = "trk"; + status = "disabled"; + + lanes { + usb2-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-1 { + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-2 { + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-3 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + hsic { + clocks = <&tegra_car TEGRA210_CLK_HSIC_TRK>; + clock-names = "trk"; + status = "disabled"; + + lanes { + hsic-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + hsic-1 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + pcie { + clocks = <&tegra_car TEGRA210_CLK_PLL_E>; + clock-names = "pll"; + resets = <&tegra_car 205>; + reset-names = "phy"; + status = "disabled"; + + lanes { + pcie-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-1 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-2 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-3 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-4 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-5 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-6 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + sata { + clocks = <&tegra_car TEGRA210_CLK_PLL_E>; + clock-names = "pll"; + resets = <&tegra_car 204>; + reset-names = "phy"; + status = "disabled"; + + lanes { + sata-0 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + }; + + ports { + usb2-0 { + status = "disabled"; + }; + + usb2-1 { + status = "disabled"; + }; + + usb2-2 { + status = "disabled"; + }; + + usb2-3 { + status = "disabled"; + }; + + hsic-0 { + status = "disabled"; + }; + + hsic-1 { + status = "disabled"; + }; + + usb3-0 { + status = "disabled"; + }; + + usb3-1 { + status = "disabled"; + }; + + usb3-2 { + status = "disabled"; + }; + + usb3-3 { + status = "disabled"; + }; + }; + }; + +Board file: + + padctl@7009f000 { + status = "okay"; + + pads { + usb2 { + status = "okay"; + + lanes { + usb2-0 { + nvidia,function = "xusb"; + status = "okay"; + }; + + usb2-1 { + nvidia,function = "xusb"; + status = "okay"; + }; + + usb2-2 { + nvidia,function = "xusb"; + status = "okay"; + }; + + usb2-3 { + nvidia,function = "xusb"; + status = "okay"; + }; + }; + }; + + pcie { + status = "okay"; + + lanes { + pcie-0 { + nvidia,function = "pcie-x1"; + status = "okay"; + }; + + pcie-1 { + nvidia,function = "pcie-x4"; + status = "okay"; + }; + + pcie-2 { + nvidia,function = "pcie-x4"; + status = "okay"; + }; + + pcie-3 { + nvidia,function = "pcie-x4"; + status = "okay"; + }; + + pcie-4 { + nvidia,function = "pcie-x4"; + status = "okay"; + }; + + pcie-5 { + nvidia,function = "usb3-ss"; + status = "okay"; + }; + + pcie-6 { + nvidia,function = "usb3-ss"; + status = "okay"; + }; + }; + }; + + sata { + status = "okay"; + + lanes { + sata-0 { + nvidia,function = "sata"; + status = "okay"; + }; + }; + }; + }; + + ports { + usb2-0 { + status = "okay"; + mode = "otg"; + }; + + usb2-1 { + status = "okay"; + vbus-supply = <&vdd_5v0_rtl>; + mode = "host"; + }; + + usb2-2 { + status = "okay"; + vbus-supply = <&vdd_usb_vbus>; + mode = "host"; + }; + + usb2-3 { + status = "okay"; + mode = "host"; + }; + + usb3-0 { + status = "okay"; + nvidia,lanes = "pcie-6"; + nvidia,port = <1>; + }; + + usb3-1 { + status = "okay"; + nvidia,lanes = "pcie-5"; + nvidia,port = <2>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-cpcap-usb.txt b/Documentation/devicetree/bindings/phy/phy-cpcap-usb.txt new file mode 100644 index 000000000000..2eb9b2b69037 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-cpcap-usb.txt @@ -0,0 +1,40 @@ +Motorola CPCAP PMIC USB PHY binding + +Required properties: +compatible: Shall be either "motorola,cpcap-usb-phy" or + "motorola,mapphone-cpcap-usb-phy" +#phy-cells: Shall be 0 +interrupts: CPCAP PMIC interrupts used by the USB PHY +interrupt-names: Interrupt names +io-channels: IIO ADC channels used by the USB PHY +io-channel-names: IIO ADC channel names +vusb-supply: Regulator for the PHY + +Optional properties: +pinctrl: Optional alternate pin modes for the PHY +pinctrl-names: Names for optional pin modes +mode-gpios: Optional GPIOs for configuring alternate modes + +Example: +cpcap_usb2_phy: phy { + compatible = "motorola,mapphone-cpcap-usb-phy"; + pinctrl-0 = <&usb_gpio_mux_sel1 &usb_gpio_mux_sel2>; + pinctrl-1 = <&usb_ulpi_pins>; + pinctrl-2 = <&usb_utmi_pins>; + pinctrl-3 = <&uart3_pins>; + pinctrl-names = "default", "ulpi", "utmi", "uart"; + #phy-cells = <0>; + interrupts-extended = < + &cpcap 15 0 &cpcap 14 0 &cpcap 28 0 &cpcap 19 0 + &cpcap 18 0 &cpcap 17 0 &cpcap 16 0 &cpcap 49 0 + &cpcap 48 1 + >; + interrupt-names = + "id_ground", "id_float", "se0conn", "vbusvld", + "sessvld", "sessend", "se1", "dm", "dp"; + mode-gpios = <&gpio2 28 GPIO_ACTIVE_HIGH + &gpio1 0 GPIO_ACTIVE_HIGH>; + io-channels = <&cpcap_adc 2>, <&cpcap_adc 7>; + io-channel-names = "vbus", "id"; + vusb-supply = <&vusb>; +}; diff --git a/Documentation/devicetree/bindings/phy/phy-da8xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-da8xx-usb.txt new file mode 100644 index 000000000000..c26478be391b --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-da8xx-usb.txt @@ -0,0 +1,40 @@ +TI DA8xx/OMAP-L1xx/AM18xx USB PHY + +Required properties: + - compatible: must be "ti,da830-usb-phy". + - #phy-cells: must be 1. + +This device controls the PHY for both the USB 1.1 OHCI and USB 2.0 OTG +controllers on DA8xx SoCs. Consumers of this device should use index 0 for +the USB 2.0 phy device and index 1 for the USB 1.1 phy device. + +It also requires a "syscon" node with compatible = "ti,da830-cfgchip", "syscon" +to access the CFGCHIP2 register. + +Example: + + cfgchip: cfgchip@1417c { + compatible = "ti,da830-cfgchip", "syscon"; + reg = <0x1417c 0x14>; + }; + + usb_phy: usb-phy { + compatible = "ti,da830-usb-phy"; + #phy-cells = <1>; + }; + + usb20: usb@200000 { + compatible = "ti,da830-musb"; + reg = <0x200000 0x1000>; + interrupts = <58>; + phys = <&usb_phy 0>; + phy-names = "usb-phy"; + }; + + usb11: usb@225000 { + compatible = "ti,da830-ohci"; + reg = <0x225000 0x1000>; + interrupts = <59>; + phys = <&usb_phy 1>; + phy-names = "usb-phy"; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-lpc18xx-usb-otg.txt b/Documentation/devicetree/bindings/phy/phy-lpc18xx-usb-otg.txt index bd61b467e30a..3bb821cd6a7f 100644 --- a/Documentation/devicetree/bindings/phy/phy-lpc18xx-usb-otg.txt +++ b/Documentation/devicetree/bindings/phy/phy-lpc18xx-usb-otg.txt @@ -18,7 +18,7 @@ creg: syscon@40043000 { compatible = "nxp,lpc1850-creg", "syscon", "simple-mfd"; reg = <0x40043000 0x1000>; - usb0_otg_phy: phy@004 { + usb0_otg_phy: phy { compatible = "nxp,lpc1850-usb-otg-phy"; clocks = <&ccu1 CLK_USB0>; #phy-cells = <0>; diff --git a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt index 00100cf3e037..0acc5a99fb79 100644 --- a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt +++ b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt @@ -4,12 +4,13 @@ mt65xx USB3.0 PHY binding This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC. Required properties (controller (parent) node): - - compatible : should be "mediatek,mt8173-u3phy" - - reg : offset and length of register for phy, exclude port's - register. - - clocks : a list of phandle + clock-specifier pairs, one for each - entry in clock-names - - clock-names : must contain + - compatible : should be one of + "mediatek,mt2701-u3phy" + "mediatek,mt2712-u3phy" + "mediatek,mt8173-u3phy" + - clocks : (deprecated, use port's clocks instead) a list of phandle + + clock-specifier pairs, one for each entry in clock-names + - clock-names : (deprecated, use port's one instead) must contain "u3phya_ref": for reference clock of usb3.0 analog phy. Required nodes : a sub-node is required for each port the controller @@ -17,8 +18,19 @@ Required nodes : a sub-node is required for each port the controller 'reg' property is used inside these nodes to describe the controller's topology. +Optional properties (controller (parent) node): + - reg : offset and length of register shared by multiple ports, + exclude port's private register. It is needed on mt2701 + and mt8173, but not on mt2712. + Required properties (port (child) node): - reg : address and length of the register set for the port. +- clocks : a list of phandle + clock-specifier pairs, one for each + entry in clock-names +- clock-names : must contain + "ref": 48M reference clock for HighSpeed analog phy; and 26M + reference clock for SuperSpeed analog phy, sometimes is + 24M, 25M or 27M, depended on platform. - #phy-cells : should be 1 (See second example) cell after port phandle is phy type from: - PHY_TYPE_USB2 @@ -29,21 +41,31 @@ Example: u3phy: usb-phy@11290000 { compatible = "mediatek,mt8173-u3phy"; reg = <0 0x11290000 0 0x800>; - clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>; - clock-names = "u3phya_ref"; #address-cells = <2>; #size-cells = <2>; ranges; status = "okay"; - phy_port0: port@11290800 { - reg = <0 0x11290800 0 0x800>; + u2port0: usb-phy@11290800 { + reg = <0 0x11290800 0 0x100>; + clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>; + clock-names = "ref"; #phy-cells = <1>; status = "okay"; }; - phy_port1: port@11291000 { - reg = <0 0x11291000 0 0x800>; + u3port0: usb-phy@11290900 { + reg = <0 0x11290800 0 0x700>; + clocks = <&clk26m>; + clock-names = "ref"; + #phy-cells = <1>; + status = "okay"; + }; + + u2port1: usb-phy@11291000 { + reg = <0 0x11291000 0 0x100>; + clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>; + clock-names = "ref"; #phy-cells = <1>; status = "okay"; }; @@ -62,7 +84,54 @@ Example: usb30: usb@11270000 { ... - phys = <&phy_port0 PHY_TYPE_USB3>; - phy-names = "usb3-0"; + phys = <&u2port0 PHY_TYPE_USB2>, <&u3port0 PHY_TYPE_USB3>; + phy-names = "usb2-0", "usb3-0"; ... }; + + +Layout differences of banks between mt8173/mt2701 and mt2712 +------------------------------------------------------------- +mt8173 and mt2701: +port offset bank +shared 0x0000 SPLLC + 0x0100 FMREG +u2 port0 0x0800 U2PHY_COM +u3 port0 0x0900 U3PHYD + 0x0a00 U3PHYD_BANK2 + 0x0b00 U3PHYA + 0x0c00 U3PHYA_DA +u2 port1 0x1000 U2PHY_COM +u3 port1 0x1100 U3PHYD + 0x1200 U3PHYD_BANK2 + 0x1300 U3PHYA + 0x1400 U3PHYA_DA +u2 port2 0x1800 U2PHY_COM + ... + +mt2712: +port offset bank +u2 port0 0x0000 MISC + 0x0100 FMREG + 0x0300 U2PHY_COM +u3 port0 0x0700 SPLLC + 0x0800 CHIP + 0x0900 U3PHYD + 0x0a00 U3PHYD_BANK2 + 0x0b00 U3PHYA + 0x0c00 U3PHYA_DA +u2 port1 0x1000 MISC + 0x1100 FMREG + 0x1300 U2PHY_COM +u3 port1 0x1700 SPLLC + 0x1800 CHIP + 0x1900 U3PHYD + 0x1a00 U3PHYD_BANK2 + 0x1b00 U3PHYA + 0x1c00 U3PHYA_DA +u2 port2 0x2000 MISC + ... + + SPLLC shared by u3 ports and FMREG shared by u2 ports on +mt8173/mt2701 are put back into each port; a new bank MISC for +u2 ports and CHIP for u3 ports are added on mt2712. diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt new file mode 100644 index 000000000000..84d59b0db8df --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt @@ -0,0 +1,71 @@ +ROCKCHIP USB2.0 PHY WITH INNO IP BLOCK + +Required properties (phy (parent) node): + - compatible : should be one of the listed compatibles: + * "rockchip,rk3228-usb2phy" + * "rockchip,rk3328-usb2phy" + * "rockchip,rk3366-usb2phy" + * "rockchip,rk3399-usb2phy" + - reg : the address offset of grf for usb-phy configuration. + - #clock-cells : should be 0. + - clock-output-names : specify the 480m output clock name. + +Optional properties: + - clocks : phandle + phy specifier pair, for the input clock of phy. + - clock-names : input clock name of phy, must be "phyclk". + - assigned-clocks : phandle of usb 480m clock. + - assigned-clock-parents : parent of usb 480m clock, select between + usb-phy output 480m and xin24m. + Refer to clk/clock-bindings.txt for generic clock + consumer properties. + +Required nodes : a sub-node is required for each port the phy provides. + The sub-node name is used to identify host or otg port, + and shall be the following entries: + * "otg-port" : the name of otg port. + * "host-port" : the name of host port. + +Required properties (port (child) node): + - #phy-cells : must be 0. See ./phy-bindings.txt for details. + - interrupts : specify an interrupt for each entry in interrupt-names. + - interrupt-names : a list which shall be the following entries: + * "otg-id" : for the otg id interrupt. + * "otg-bvalid" : for the otg vbus interrupt. + * "linestate" : for the host/otg linestate interrupt. + +Optional properties: + - phy-supply : phandle to a regulator that provides power to VBUS. + See ./phy-bindings.txt for details. + +Example: + +grf: syscon@ff770000 { + compatible = "rockchip,rk3366-grf", "syscon", "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + +... + + u2phy: usb2-phy@700 { + compatible = "rockchip,rk3366-usb2phy"; + reg = <0x700 0x2c>; + #clock-cells = <0>; + clock-output-names = "sclk_otgphy0_480m"; + + u2phy_otg: otg-port { + #phy-cells = <0>; + interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "otg-id", "otg-bvalid", "linestate"; + status = "okay"; + }; + + u2phy_host: host-port { + #phy-cells = <0>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "linestate"; + status = "okay"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt new file mode 100644 index 000000000000..6ea867e3176f --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt @@ -0,0 +1,101 @@ +* ROCKCHIP type-c PHY +--------------------- + +Required properties: + - compatible : must be "rockchip,rk3399-typec-phy" + - reg: Address and length of the usb phy control register set + - rockchip,grf : phandle to the syscon managing the "general + register files" + - clocks : phandle + clock specifier for the phy clocks + - clock-names : string, clock name, must be "tcpdcore", "tcpdphy-ref"; + - assigned-clocks: main clock, should be <&cru SCLK_UPHY0_TCPDCORE> or + <&cru SCLK_UPHY1_TCPDCORE>; + - assigned-clock-rates : the phy core clk frequency, shall be: 50000000 + - resets : a list of phandle + reset specifier pairs + - reset-names : string reset name, must be: + "uphy", "uphy-pipe", "uphy-tcphy" + - extcon : extcon specifier for the Power Delivery + +Note, there are 2 type-c phys for RK3399, and they are almost identical, except +these registers(description below), every register node contains 3 sections: +offset, enable bit, write mask bit. + - rockchip,typec-conn-dir : the register of type-c connector direction, + for type-c phy0, it must be <0xe580 0 16>; + for type-c phy1, it must be <0xe58c 0 16>; + - rockchip,usb3tousb2-en : the register of type-c force usb3 to usb2 enable + control. + for type-c phy0, it must be <0xe580 3 19>; + for type-c phy1, it must be <0xe58c 3 19>; + - rockchip,external-psm : the register of type-c phy external psm clock + selection. + for type-c phy0, it must be <0xe588 14 30>; + for type-c phy1, it must be <0xe594 14 30>; + - rockchip,pipe-status : the register of type-c phy pipe status. + for type-c phy0, it must be <0xe5c0 0 0>; + for type-c phy1, it must be <0xe5c0 16 16>; + +Required nodes : a sub-node is required for each port the phy provides. + The sub-node name is used to identify dp or usb3 port, + and shall be the following entries: + * "dp-port" : the name of DP port. + * "usb3-port" : the name of USB3 port. + +Required properties (port (child) node): +- #phy-cells : must be 0, See ./phy-bindings.txt for details. + +Example: + tcphy0: phy@ff7c0000 { + compatible = "rockchip,rk3399-typec-phy"; + reg = <0x0 0xff7c0000 0x0 0x40000>; + rockchip,grf = <&grf>; + extcon = <&fusb0>; + clocks = <&cru SCLK_UPHY0_TCPDCORE>, + <&cru SCLK_UPHY0_TCPDPHY_REF>; + clock-names = "tcpdcore", "tcpdphy-ref"; + assigned-clocks = <&cru SCLK_UPHY0_TCPDCORE>; + assigned-clock-rates = <50000000>; + resets = <&cru SRST_UPHY0>, + <&cru SRST_UPHY0_PIPE_L00>, + <&cru SRST_P_UPHY0_TCPHY>; + reset-names = "uphy", "uphy-pipe", "uphy-tcphy"; + rockchip,typec-conn-dir = <0xe580 0 16>; + rockchip,usb3tousb2-en = <0xe580 3 19>; + rockchip,external-psm = <0xe588 14 30>; + rockchip,pipe-status = <0xe5c0 0 0>; + + tcphy0_dp: dp-port { + #phy-cells = <0>; + }; + + tcphy0_usb3: usb3-port { + #phy-cells = <0>; + }; + }; + + tcphy1: phy@ff800000 { + compatible = "rockchip,rk3399-typec-phy"; + reg = <0x0 0xff800000 0x0 0x40000>; + rockchip,grf = <&grf>; + extcon = <&fusb1>; + clocks = <&cru SCLK_UPHY1_TCPDCORE>, + <&cru SCLK_UPHY1_TCPDPHY_REF>; + clock-names = "tcpdcore", "tcpdphy-ref"; + assigned-clocks = <&cru SCLK_UPHY1_TCPDCORE>; + assigned-clock-rates = <50000000>; + resets = <&cru SRST_UPHY1>, + <&cru SRST_UPHY1_PIPE_L00>, + <&cru SRST_P_UPHY1_TCPHY>; + reset-names = "uphy", "uphy-pipe", "uphy-tcphy"; + rockchip,typec-conn-dir = <0xe58c 0 16>; + rockchip,usb3tousb2-en = <0xe58c 3 19>; + rockchip,external-psm = <0xe594 14 30>; + rockchip,pipe-status = <0xe5c0 16 16>; + + tcphy1_dp: dp-port { + #phy-cells = <0>; + }; + + tcphy1_usb3: usb3-port { + #phy-cells = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt b/Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt index 00944a05ee6b..744b4809542e 100644 --- a/Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt +++ b/Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt @@ -17,7 +17,7 @@ Example: usb2_phy: usb2phy@0 { compatible = "st,stih416-usb-phy"; - #phy-cell = <0>; + #phy-cells = <0>; st,syscfg = <&syscfg_rear>; clocks = <&clk_sysin>; clock-names = "osc_phy"; diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.txt b/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.txt new file mode 100644 index 000000000000..b3b75c1e6285 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.txt @@ -0,0 +1,84 @@ +Qualcomm's USB HS PHY + +PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: Should contain "qcom,usb-hs-phy" and more specifically one of the + following: + + "qcom,usb-hs-phy-apq8064" + "qcom,usb-hs-phy-msm8916" + "qcom,usb-hs-phy-msm8974" + +- #phy-cells: + Usage: required + Value type: <u32> + Definition: Should contain 0 + +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: Should contain clock specifier for the reference and sleep + clocks + +- clock-names: + Usage: required + Value type: <stringlist> + Definition: Should contain "ref" and "sleep" for the reference and sleep + clocks respectively + +- resets: + Usage: required + Value type: <prop-encoded-array> + Definition: Should contain the phy and POR resets + +- reset-names: + Usage: required + Value type: <stringlist> + Definition: Should contain "phy" and "por" for the phy and POR resets + respectively + +- v3p3-supply: + Usage: required + Value type: <phandle> + Definition: Should contain a reference to the 3.3V supply + +- v1p8-supply: + Usage: required + Value type: <phandle> + Definition: Should contain a reference to the 1.8V supply + +- extcon: + Usage: optional + Value type: <prop-encoded-array> + Definition: Should contain the vbus extcon + +- qcom,init-seq: + Usage: optional + Value type: <u8 array> + Definition: Should contain a sequence of ULPI address and value pairs to + program into the ULPI_EXT_VENDOR_SPECIFIC area. This is related + to Device Mode Eye Diagram test. The addresses are offsets + from the ULPI_EXT_VENDOR_SPECIFIC address, for example, + <0x1 0x53> would mean "write the value 0x53 to address 0x81". + +EXAMPLE + +otg: usb-controller { + ulpi { + phy { + compatible = "qcom,usb-hs-phy-msm8974", "qcom,usb-hs-phy"; + #phy-cells = <0>; + clocks = <&xo_board>, <&gcc GCC_USB2A_PHY_SLEEP_CLK>; + clock-names = "ref", "sleep"; + resets = <&gcc GCC_USB2A_PHY_BCR>, <&otg 0>; + reset-names = "phy", "por"; + v3p3-supply = <&pm8941_l24>; + v1p8-supply = <&pm8941_l6>; + extcon = <&smbb>; + qcom,init-seq = /bits/ 8 <0x1 0x63>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-hsic-phy.txt b/Documentation/devicetree/bindings/phy/qcom,usb-hsic-phy.txt new file mode 100644 index 000000000000..3c7cb2be4b12 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,usb-hsic-phy.txt @@ -0,0 +1,65 @@ +Qualcomm's USB HSIC PHY + +PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: Should contain "qcom,usb-hsic-phy" and more specifically one of the + following: + + "qcom,usb-hsic-phy-mdm9615" + "qcom,usb-hsic-phy-msm8974" + +- #phy-cells: + Usage: required + Value type: <u32> + Definition: Should contain 0 + +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: Should contain clock specifier for phy, calibration and + a calibration sleep clock + +- clock-names: + Usage: required + Value type: <stringlist> + Definition: Should contain "phy, "cal" and "cal_sleep" + +- pinctrl-names: + Usage: required + Value type: <stringlist> + Definition: Should contain "init" and "default" in that order + +- pinctrl-0: + Usage: required + Value type: <prop-encoded-array> + Definition: List of pinctrl settings to apply to keep HSIC pins in a glitch + free state + +- pinctrl-1: + Usage: required + Value type: <prop-encoded-array> + Definition: List of pinctrl settings to apply to mux out the HSIC pins + +EXAMPLE + +usb-controller { + ulpi { + phy { + compatible = "qcom,usb-hsic-phy-msm8974", + "qcom,usb-hsic-phy"; + #phy-cells = <0>; + pinctrl-names = "init", "default"; + pinctrl-0 = <&hsic_sleep>; + pinctrl-1 = <&hsic_default>; + clocks = <&gcc GCC_USB_HSIC_CLK>, + <&gcc GCC_USB_HSIC_IO_CAL_CLK>, + <&gcc GCC_USB_HSIC_IO_CAL_SLEEP_CLK>; + clock-names = "phy", "cal", "cal_sleep"; + assigned-clocks = <&gcc GCC_USB_HSIC_IO_CAL_CLK>; + assigned-clock-rates = <960000>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt new file mode 100644 index 000000000000..e11c563a65ec --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt @@ -0,0 +1,106 @@ +Qualcomm QMP PHY controller +=========================== + +QMP phy controller supports physical layer functionality for a number of +controllers on Qualcomm chipsets, such as, PCIe, UFS, and USB. + +Required properties: + - compatible: compatible list, contains: + "qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996, + "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996. + + - reg: offset and length of register set for PHY's common serdes block. + + - #clock-cells: must be 1 + - Phy pll outputs a bunch of clocks for Tx, Rx and Pipe + interface (for pipe based PHYs). These clock are then gate-controlled + by gcc. + - #address-cells: must be 1 + - #size-cells: must be 1 + - ranges: must be present + + - clocks: a list of phandles and clock-specifier pairs, + one for each entry in clock-names. + - clock-names: "cfg_ahb" for phy config clock, + "aux" for phy aux clock, + "ref" for 19.2 MHz ref clk, + For "qcom,msm8996-qmp-pcie-phy" must contain: + "aux", "cfg_ahb", "ref". + For "qcom,msm8996-qmp-usb3-phy" must contain: + "aux", "cfg_ahb", "ref". + + - resets: a list of phandles and reset controller specifier pairs, + one for each entry in reset-names. + - reset-names: "phy" for reset of phy block, + "common" for phy common block reset, + "cfg" for phy's ahb cfg block reset (Optional). + For "qcom,msm8996-qmp-pcie-phy" must contain: + "phy", "common", "cfg". + For "qcom,msm8996-qmp-usb3-phy" must contain + "phy", "common". + + - vdda-phy-supply: Phandle to a regulator supply to PHY core block. + - vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block. + +Optional properties: + - vddp-ref-clk-supply: Phandle to a regulator supply to any specific refclk + pll block. + +Required nodes: + - Each device node of QMP phy is required to have as many child nodes as + the number of lanes the PHY has. + +Required properties for child node: + - reg: list of offset and length pairs of register sets for PHY blocks - + tx, rx and pcs. + + - #phy-cells: must be 0 + + - clocks: a list of phandles and clock-specifier pairs, + one for each entry in clock-names. + - clock-names: Must contain following for pcie and usb qmp phys: + "pipe<lane-number>" for pipe clock specific to each lane. + + - resets: a list of phandles and reset controller specifier pairs, + one for each entry in reset-names. + - reset-names: Must contain following for pcie qmp phys: + "lane<lane-number>" for reset specific to each lane. + +Example: + phy@34000 { + compatible = "qcom,msm8996-qmp-pcie-phy"; + reg = <0x34000 0x488>; + #clock-cells = <1>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>, + <&gcc GCC_PCIE_PHY_CFG_AHB_CLK>, + <&gcc GCC_PCIE_CLKREF_CLK>; + clock-names = "aux", "cfg_ahb", "ref"; + + vdda-phy-supply = <&pm8994_l28>; + vdda-pll-supply = <&pm8994_l12>; + + resets = <&gcc GCC_PCIE_PHY_BCR>, + <&gcc GCC_PCIE_PHY_COM_BCR>, + <&gcc GCC_PCIE_PHY_COM_NOCSR_BCR>; + reset-names = "phy", "common", "cfg"; + + pciephy_0: lane@35000 { + reg = <0x35000 0x130>, + <0x35200 0x200>, + <0x35400 0x1dc>; + #phy-cells = <0>; + + clocks = <&gcc GCC_PCIE_0_PIPE_CLK>; + clock-names = "pipe0"; + resets = <&gcc GCC_PCIE_0_PHY_BCR>; + reset-names = "lane0"; + }; + + pciephy_1: lane@36000 { + ... + ... + }; diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt new file mode 100644 index 000000000000..aa0fcb05acb3 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt @@ -0,0 +1,43 @@ +Qualcomm QUSB2 phy controller +============================= + +QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets. + +Required properties: + - compatible: compatible list, contains "qcom,msm8996-qusb2-phy". + - reg: offset and length of the PHY register set. + - #phy-cells: must be 0. + + - clocks: a list of phandles and clock-specifier pairs, + one for each entry in clock-names. + - clock-names: must be "cfg_ahb" for phy config clock, + "ref" for 19.2 MHz ref clk, + "iface" for phy interface clock (Optional). + + - vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block. + - vdda-phy-dpdm-supply: Phandle to 3.1V regulator supply to Dp/Dm port signals. + + - resets: Phandle to reset to phy block. + +Optional properties: + - nvmem-cells: Phandle to nvmem cell that contains 'HS Tx trim' + tuning parameter value for qusb2 phy. + + - qcom,tcsr-syscon: Phandle to TCSR syscon register region. + +Example: + hsusb_phy: phy@7411000 { + compatible = "qcom,msm8996-qusb2-phy"; + reg = <0x7411000 0x180>; + #phy-cells = <0>; + + clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>, + <&gcc GCC_RX1_USB2_CLKREF_CLK>, + clock-names = "cfg_ahb", "ref"; + + vdda-pll-supply = <&pm8994_l12>; + vdda-phy-dpdm-supply = <&pm8994_l24>; + + resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>; + nvmem-cells = <&qusb2p_hstx_trim>; + }; diff --git a/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt b/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt index d564ba4f1cf6..91da947ae9b6 100644 --- a/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt +++ b/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt @@ -7,6 +7,12 @@ Required properties: - compatible: "renesas,usb-phy-r8a7790" if the device is a part of R8A7790 SoC. "renesas,usb-phy-r8a7791" if the device is a part of R8A7791 SoC. "renesas,usb-phy-r8a7794" if the device is a part of R8A7794 SoC. + "renesas,rcar-gen2-usb-phy" for a generic R-Car Gen2 compatible device. + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + - reg: offset and length of the register block. - #address-cells: number of address cells for the USB channel subnodes, must be <1>. @@ -34,7 +40,7 @@ the USB channel; see the selector meanings below: Example (Lager board): usb-phy@e6590100 { - compatible = "renesas,usb-phy-r8a7790"; + compatible = "renesas,usb-phy-r8a7790", "renesas,rcar-gen2-usb-phy"; reg = <0 0xe6590100 0 0x100>; #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt index 2390e4e9c84c..ace9cce2704a 100644 --- a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt +++ b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt @@ -6,34 +6,37 @@ This file provides information on what the device node for the R-Car generation Required properties: - compatible: "renesas,usb2-phy-r8a7795" if the device is a part of an R8A7795 SoC. + "renesas,usb2-phy-r8a7796" if the device is a part of an R8A7796 + SoC. + "renesas,rcar-gen3-usb2-phy" for a generic R-Car Gen3 compatible device. + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + - reg: offset and length of the partial USB 2.0 Host register block. -- reg-names: must be "usb2_host". - clocks: clock phandle and specifier pair(s). - #phy-cells: see phy-bindings.txt in the same directory, must be <0>. Optional properties: To use a USB channel where USB 2.0 Host and HSUSB (USB 2.0 Peripheral) are -combined, the device tree node should set HSUSB properties to reg and reg-names -properties. This is because HSUSB has registers to select USB 2.0 host or -peripheral at that channel: -- reg: offset and length of the partial HSUSB register block. -- reg-names: must be "hsusb". +combined, the device tree node should set interrupt properties to use the +channel as USB OTG: - interrupts: interrupt specifier for the PHY. +- vbus-supply: Phandle to a regulator that provides power to the VBUS. This + regulator will be managed during the PHY power on/off sequence. Example (R-Car H3): usb-phy@ee080200 { - compatible = "renesas,usb2-phy-r8a7795"; - reg = <0 0xee080200 0 0x700>, <0 0xe6590100 0 0x100>; - reg-names = "usb2_host", "hsusb"; + compatible = "renesas,usb2-phy-r8a7795", "renesas,rcar-gen3-usb2-phy"; + reg = <0 0xee080200 0 0x700>; interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp7_clks R8A7795_CLK_EHCI0>, - <&mstp7_clks R8A7795_CLK_HSUSB>; + clocks = <&cpg CPG_MOD 703>; }; usb-phy@ee0a0200 { - compatible = "renesas,usb2-phy-r8a7795"; + compatible = "renesas,usb2-phy-r8a7795", "renesas,rcar-gen3-usb2-phy"; reg = <0 0xee0a0200 0 0x700>; - reg-names = "usb2_host"; - clocks = <&mstp7_clks R8A7795_CLK_EHCI0>; + clocks = <&cpg CPG_MOD 702>; }; diff --git a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb3.txt b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb3.txt new file mode 100644 index 000000000000..f94cea48f6b1 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb3.txt @@ -0,0 +1,46 @@ +* Renesas R-Car generation 3 USB 3.0 PHY + +This file provides information on what the device node for the R-Car generation +3 USB 3.0 PHY contains. +If you want to enable spread spectrum clock (ssc), you should use USB_EXTAL +instead of USB3_CLK. However, if you don't want to these features, you don't +need this driver. + +Required properties: +- compatible: "renesas,r8a7795-usb3-phy" if the device is a part of an R8A7795 + SoC. + "renesas,r8a7796-usb3-phy" if the device is a part of an R8A7796 + SoC. + "renesas,rcar-gen3-usb3-phy" for a generic R-Car Gen3 compatible + device. + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + +- reg: offset and length of the USB 3.0 PHY register block. +- clocks: A list of phandles and clock-specifier pairs. +- clock-names: Name of the clocks. + - The funcional clock must be "usb3-if". + - The usb3's external clock must be "usb3s_clk". + - The usb2's external clock must be "usb_extal". If you want to use the ssc, + the clock-frequency must not be 0. +- #phy-cells: see phy-bindings.txt in the same directory, must be <0>. + +Optional properties: +- renesas,ssc-range: Enable/disable spread spectrum clock (ssc) by using + the following values as u32: + - 0 (or the property doesn't exist): disable the ssc + - 4980: enable the ssc as -4980 ppm + - 4492: enable the ssc as -4492 ppm + - 4003: enable the ssc as -4003 ppm + +Example (R-Car H3): + + usb-phy@e65ee000 { + compatible = "renesas,r8a7795-usb3-phy", + "renesas,rcar-gen3-usb3-phy"; + reg = <0 0xe65ee000 0 0x90>; + clocks = <&cpg CPG_MOD 328>, <&usb3s0_clk>, <&usb_extal>; + clock-names = "usb3-if", "usb3s_clk", "usb_extal"; + }; diff --git a/Documentation/devicetree/bindings/phy/rockchip-dp-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-dp-phy.txt new file mode 100644 index 000000000000..e3b4809fbe82 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rockchip-dp-phy.txt @@ -0,0 +1,26 @@ +Rockchip specific extensions to the Analogix Display Port PHY +------------------------------------ + +Required properties: +- compatible : should be one of the following supported values: + - "rockchip.rk3288-dp-phy" +- clocks: from common clock binding: handle to dp clock. + of memory mapped region. +- clock-names: from common clock binding: + Required elements: "24m" +- #phy-cells : from the generic PHY bindings, must be 0; + +Example: + +grf: syscon@ff770000 { + compatible = "rockchip,rk3288-grf", "syscon", "simple-mfd"; + +... + + edp_phy: edp-phy { + compatible = "rockchip,rk3288-dp-phy"; + clocks = <&cru SCLK_EDP_24M>; + clock-names = "24m"; + #phy-cells = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt new file mode 100644 index 000000000000..e3ea55763b0a --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt @@ -0,0 +1,34 @@ +Rockchip EMMC PHY +----------------------- + +Required properties: + - compatible: rockchip,rk3399-emmc-phy + - #phy-cells: must be 0 + - reg: PHY register address offset and length in "general + register files" + +Optional clocks using the clock bindings (see ../clock/clock-bindings.txt), +specified by name: + - clock-names: Should contain "emmcclk". Although this is listed as optional + (because most boards can get basic functionality without having + access to it), it is strongly suggested. + - clocks: Should have a phandle to the card clock exported by the SDHCI driver. + +Example: + + +grf: syscon@ff770000 { + compatible = "rockchip,rk3399-grf", "syscon", "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + +... + + emmcphy: phy@f780 { + compatible = "rockchip,rk3399-emmc-phy"; + reg = <0xf780 0x20>; + clocks = <&sdhci>; + clock-names = "emmcclk"; + #phy-cells = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/rockchip-pcie-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-pcie-phy.txt new file mode 100644 index 000000000000..0f6222a672ce --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rockchip-pcie-phy.txt @@ -0,0 +1,31 @@ +Rockchip PCIE PHY +----------------------- + +Required properties: + - compatible: rockchip,rk3399-pcie-phy + - #phy-cells: must be 0 + - clocks: Must contain an entry in clock-names. + See ../clocks/clock-bindings.txt for details. + - clock-names: Must be "refclk" + - resets: Must contain an entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must be "phy" + +Example: + +grf: syscon@ff770000 { + compatible = "rockchip,rk3399-grf", "syscon", "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + + ... + + pcie_phy: pcie-phy { + compatible = "rockchip,rk3399-pcie-phy"; + #phy-cells = <0>; + clocks = <&cru SCLK_PCIEPHY_REF>; + clock-names = "refclk"; + resets = <&cru SRST_PCIEPHY>; + reset-names = "phy"; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt index 68498d560354..4ed569046daf 100644 --- a/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt @@ -5,11 +5,13 @@ Required properties: "rockchip,rk3066a-usb-phy" "rockchip,rk3188-usb-phy" "rockchip,rk3288-usb-phy" - - rockchip,grf : phandle to the syscon managing the "general - register files" - #address-cells: should be 1 - #size-cells: should be 0 +Deprecated properties: + - rockchip,grf : phandle to the syscon managing the "general + register files" - phy should be a child of the GRF instead + Sub-nodes: Each PHY should be represented as a sub-node. @@ -25,17 +27,26 @@ Optional Properties: - clocks : phandle + clock specifier for the phy clocks - clock-names: string, clock name, must be "phyclk" - #clock-cells: for users of the phy-pll, should be 0 +- reset-names: Only allow the following entries: + - phy-reset +- resets: Must contain an entry for each entry in reset-names. +- vbus-supply: power-supply phandle for vbus power source Example: -usbphy: phy { - compatible = "rockchip,rk3288-usb-phy"; - rockchip,grf = <&grf>; - #address-cells = <1>; - #size-cells = <0>; +grf: syscon@ff770000 { + compatible = "rockchip,rk3288-grf", "syscon", "simple-mfd"; + +... + + usbphy: phy { + compatible = "rockchip,rk3288-usb-phy"; + #address-cells = <1>; + #size-cells = <0>; - usbphy0: usb-phy0 { - #phy-cells = <0>; - reg = <0x320>; + usbphy0: usb-phy0 { + #phy-cells = <0>; + reg = <0x320>; + }; }; }; diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt index 0289d3b07853..ab80bfe31cb3 100644 --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt @@ -2,9 +2,20 @@ Samsung S5P/EXYNOS SoC series MIPI CSIS/DSIM DPHY ------------------------------------------------- Required properties: -- compatible : should be "samsung,s5pv210-mipi-video-phy"; +- compatible : should be one of the listed compatibles: + - "samsung,s5pv210-mipi-video-phy" + - "samsung,exynos5420-mipi-video-phy" + - "samsung,exynos5433-mipi-video-phy" - #phy-cells : from the generic phy bindings, must be 1; -- syscon - phandle to the PMU system controller; + +In case of s5pv210 and exynos5420 compatible PHYs: +- syscon - phandle to the PMU system controller + +In case of exynos5433 compatible PHY: + - samsung,pmu-syscon - phandle to the PMU system controller + - samsung,disp-sysreg - phandle to the DISP system registers controller + - samsung,cam0-sysreg - phandle to the CAM0 system registers controller + - samsung,cam1-sysreg - phandle to the CAM1 system registers controller For "samsung,s5pv210-mipi-video-phy" compatible PHYs the second cell in the PHY specifier identifies the PHY and its meaning is as follows: @@ -12,6 +23,9 @@ the PHY specifier identifies the PHY and its meaning is as follows: 1 - MIPI DSIM 0, 2 - MIPI CSIS 1, 3 - MIPI DSIM 1. +"samsung,exynos5420-mipi-video-phy" and "samsung,exynos5433-mipi-video-phy" +supports additional fifth PHY: + 4 - MIPI CSIS 2. Samsung EXYNOS SoC series Display Port PHY ------------------------------------------------- @@ -177,3 +191,20 @@ Example: usbdrdphy0 = &usb3_phy0; usbdrdphy1 = &usb3_phy1; }; + +Samsung Exynos SoC series PCIe PHY controller +-------------------------------------------------- +Required properties: +- compatible : Should be set to "samsung,exynos5440-pcie-phy" +- #phy-cells : Must be zero +- reg : a register used by phy driver. + - First is for phy register, second is for block register. +- reg-names : Must be set to "phy" and "block". + +Example: + pcie_phy0: pcie-phy@270000 { + #phy-cells = <0>; + compatible = "samsung,exynos5440-pcie-phy"; + reg = <0x270000 0x1000>, <0x271000 0x40>; + reg-names = "phy", "block"; + }; diff --git a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt index 95736d77fbb7..005bc22938ff 100644 --- a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt @@ -10,9 +10,12 @@ Required properties: * allwinner,sun8i-a23-usb-phy * allwinner,sun8i-a33-usb-phy * allwinner,sun8i-h3-usb-phy + * allwinner,sun8i-v3s-usb-phy + * allwinner,sun50i-a64-usb-phy - reg : a list of offset + length pairs - reg-names : * "phy_ctrl" + * "pmu0" for H3, V3s and A64 * "pmu1" * "pmu2" for sun4i, sun6i or sun7i - #phy-cells : from the generic phy bindings, must be 1 diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt index a3b394587874..cd13e6157088 100644 --- a/Documentation/devicetree/bindings/phy/ti-phy.txt +++ b/Documentation/devicetree/bindings/phy/ti-phy.txt @@ -31,6 +31,8 @@ OMAP USB2 PHY Required properties: - compatible: Should be "ti,omap-usb2" + Should be "ti,dra7x-usb2" for the 1st instance of USB2 PHY on + DRA7x Should be "ti,dra7x-usb2-phy2" for the 2nd instance of USB2 PHY in DRA7x - reg : Address and length of the register set for the device. |