diff options
Diffstat (limited to 'Documentation/devicetree/bindings/power')
62 files changed, 1633 insertions, 39 deletions
diff --git a/Documentation/devicetree/bindings/power/actions,owl-sps.txt b/Documentation/devicetree/bindings/power/actions,owl-sps.txt new file mode 100644 index 000000000000..007b9a7ae723 --- /dev/null +++ b/Documentation/devicetree/bindings/power/actions,owl-sps.txt @@ -0,0 +1,17 @@ +Actions Semi Owl Smart Power System (SPS) + +Required properties: +- compatible : "actions,s500-sps" for S500 +- reg : Offset and length of the register set for the device. +- #power-domain-cells : Must be 1. + See macros in: + include/dt-bindings/power/owl-s500-powergate.h for S500 + + +Example: + + sps: power-controller@b01b0100 { + compatible = "actions,s500-sps"; + reg = <0xb01b0100 0x100>; + #power-domain-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/power/domain-idle-state.txt b/Documentation/devicetree/bindings/power/domain-idle-state.txt new file mode 100644 index 000000000000..eefc7ed22ca2 --- /dev/null +++ b/Documentation/devicetree/bindings/power/domain-idle-state.txt @@ -0,0 +1,33 @@ +PM Domain Idle State Node: + +A domain idle state node represents the state parameters that will be used to +select the state when there are no active components in the domain. + +The state node has the following parameters - + +- compatible: + Usage: Required + Value type: <string> + Definition: Must be "domain-idle-state". + +- entry-latency-us + Usage: Required + Value type: <prop-encoded-array> + Definition: u32 value representing worst case latency in + microseconds required to enter the idle state. + The exit-latency-us duration may be guaranteed + only after entry-latency-us has passed. + +- exit-latency-us + Usage: Required + Value type: <prop-encoded-array> + Definition: u32 value representing worst case latency + in microseconds required to exit the idle state. + +- min-residency-us + Usage: Required + Value type: <prop-encoded-array> + Definition: u32 value representing minimum residency duration + in microseconds after which the idle state will yield + power benefits after overcoming the overhead in entering +i the idle state. diff --git a/Documentation/devicetree/bindings/power/fsl,imx-gpc.txt b/Documentation/devicetree/bindings/power/fsl,imx-gpc.txt index 65cc0345747d..6c1498958d48 100644 --- a/Documentation/devicetree/bindings/power/fsl,imx-gpc.txt +++ b/Documentation/devicetree/bindings/power/fsl,imx-gpc.txt @@ -1,22 +1,42 @@ Freescale i.MX General Power Controller ======================================= -The i.MX6Q General Power Control (GPC) block contains DVFS load tracking -counters and Power Gating Control (PGC) for the CPU and PU (GPU/VPU) power -domains. +The i.MX6 General Power Control (GPC) block contains DVFS load tracking +counters and Power Gating Control (PGC). Required properties: -- compatible: Should be "fsl,imx6q-gpc" or "fsl,imx6sl-gpc" +- compatible: Should be one of the following: + - fsl,imx6q-gpc + - fsl,imx6qp-gpc + - fsl,imx6sl-gpc - reg: should be register base and length as documented in the datasheet -- interrupts: Should contain GPC interrupt request 1 -- pu-supply: Link to the LDO regulator powering the PU power domain -- clocks: Clock phandles to devices in the PU power domain that need - to be enabled during domain power-up for reset propagation. -- #power-domain-cells: Should be 1, see below: +- interrupts: Should contain one interrupt specifier for the GPC interrupt +- clocks: Must contain an entry for each entry in clock-names. + See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - ipg -The gpc node is a power-controller as documented by the generic power domain -bindings in Documentation/devicetree/bindings/power/power_domain.txt. +The power domains are generic power domain providers as documented in +Documentation/devicetree/bindings/power/power_domain.txt. They are described as +subnodes of the power gating controller 'pgc' node of the GPC and should +contain the following: + +Required properties: +- reg: Must contain the DOMAIN_INDEX of this power domain + The following DOMAIN_INDEX values are valid for i.MX6Q: + ARM_DOMAIN 0 + PU_DOMAIN 1 + The following additional DOMAIN_INDEX value is valid for i.MX6SL: + DISPLAY_DOMAIN 2 + +- #power-domain-cells: Should be 0 + +Optional properties: +- clocks: a number of phandles to clocks that need to be enabled during domain + power-up sequencing to ensure reset propagation into devices located inside + this power domain +- power-supply: a phandle to the regulator powering this domain Example: @@ -25,14 +45,30 @@ Example: reg = <0x020dc000 0x4000>; interrupts = <0 89 IRQ_TYPE_LEVEL_HIGH>, <0 90 IRQ_TYPE_LEVEL_HIGH>; - pu-supply = <®_pu>; - clocks = <&clks IMX6QDL_CLK_GPU3D_CORE>, - <&clks IMX6QDL_CLK_GPU3D_SHADER>, - <&clks IMX6QDL_CLK_GPU2D_CORE>, - <&clks IMX6QDL_CLK_GPU2D_AXI>, - <&clks IMX6QDL_CLK_OPENVG_AXI>, - <&clks IMX6QDL_CLK_VPU_AXI>; - #power-domain-cells = <1>; + clocks = <&clks IMX6QDL_CLK_IPG>; + clock-names = "ipg"; + + pgc { + #address-cells = <1>; + #size-cells = <0>; + + power-domain@0 { + reg = <0>; + #power-domain-cells = <0>; + }; + + pd_pu: power-domain@1 { + reg = <1>; + #power-domain-cells = <0>; + power-supply = <®_pu>; + clocks = <&clks IMX6QDL_CLK_GPU3D_CORE>, + <&clks IMX6QDL_CLK_GPU3D_SHADER>, + <&clks IMX6QDL_CLK_GPU2D_CORE>, + <&clks IMX6QDL_CLK_GPU2D_AXI>, + <&clks IMX6QDL_CLK_OPENVG_AXI>, + <&clks IMX6QDL_CLK_VPU_AXI>; + }; + }; }; @@ -40,20 +76,13 @@ Specifying power domain for IP modules ====================================== IP cores belonging to a power domain should contain a 'power-domains' property -that is a phandle pointing to the gpc device node and a DOMAIN_INDEX specifying -the power domain the device belongs to. +that is a phandle pointing to the power domain the device belongs to. Example of a device that is part of the PU power domain: vpu: vpu@02040000 { reg = <0x02040000 0x3c000>; /* ... */ - power-domains = <&gpc 1>; + power-domains = <&pd_pu>; /* ... */ }; - -The following DOMAIN_INDEX values are valid for i.MX6Q: -ARM_DOMAIN 0 -PU_DOMAIN 1 -The following additional DOMAIN_INDEX value is valid for i.MX6SL: -DISPLAY_DOMAIN 2 diff --git a/Documentation/devicetree/bindings/power/fsl,imx-gpcv2.txt b/Documentation/devicetree/bindings/power/fsl,imx-gpcv2.txt new file mode 100644 index 000000000000..02f45c65fd87 --- /dev/null +++ b/Documentation/devicetree/bindings/power/fsl,imx-gpcv2.txt @@ -0,0 +1,71 @@ +Freescale i.MX General Power Controller v2 +========================================== + +The i.MX7S/D General Power Control (GPC) block contains Power Gating +Control (PGC) for various power domains. + +Required properties: + +- compatible: Should be "fsl,imx7d-gpc" + +- reg: should be register base and length as documented in the + datasheet + +- interrupts: Should contain GPC interrupt request 1 + +Power domains contained within GPC node are generic power domain +providers, documented in +Documentation/devicetree/bindings/power/power_domain.txt, which are +described as subnodes of the power gating controller 'pgc' node, +which, in turn, is expected to contain the following: + +Required properties: + +- reg: Power domain index. Valid values are defined in + include/dt-bindings/power/imx7-power.h + +- #power-domain-cells: Should be 0 + +Optional properties: + +- power-supply: Power supply used to power the domain + +Example: + + gpc: gpc@303a0000 { + compatible = "fsl,imx7d-gpc"; + reg = <0x303a0000 0x1000>; + interrupt-controller; + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; + #interrupt-cells = <3>; + interrupt-parent = <&intc>; + + pgc { + #address-cells = <1>; + #size-cells = <0>; + + pgc_pcie_phy: power-domain@3 { + #power-domain-cells = <0>; + + reg = <IMX7_POWER_DOMAIN_PCIE_PHY>; + power-supply = <®_1p0d>; + }; + }; + }; + + +Specifying power domain for IP modules +====================================== + +IP cores belonging to a power domain should contain a 'power-domains' +property that is a phandle for PGC node representing the domain. + +Example of a device that is part of the PCIE_PHY power domain: + + pcie: pcie@33800000 { + reg = <0x33800000 0x4000>, + <0x4ff00000 0x80000>; + /* ... */ + power-domains = <&pgc_pcie_phy>; + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/power/pd-samsung.txt b/Documentation/devicetree/bindings/power/pd-samsung.txt index 4e947372a693..549f7dee9b9d 100644 --- a/Documentation/devicetree/bindings/power/pd-samsung.txt +++ b/Documentation/devicetree/bindings/power/pd-samsung.txt @@ -6,12 +6,15 @@ to gate power to one or more peripherals on the processor. Required Properties: - compatible: should be one of the following. * samsung,exynos4210-pd - for exynos4210 type power domain. + * samsung,exynos5433-pd - for exynos5433 type power domain. - reg: physical base address of the controller and length of memory mapped region. - #power-domain-cells: number of cells in power domain specifier; must be 0. Optional Properties: +- label: Human readable string with domain name. Will be visible in userspace + to let user to distinguish between multiple domains in SoC. - clocks: List of clock handles. The parent clocks of the input clocks to the devices in this power domain are set to oscclk before power gating and restored back after powering on a domain. This is required for @@ -20,7 +23,7 @@ Optional Properties: - clock-names: The following clocks can be specified: - oscclk: Oscillator clock. - clkN: Input clocks to the devices in this power domain. These clocks - will be reparented to oscclk before swithing power domain off. + will be reparented to oscclk before switching power domain off. Their original parent will be brought back after turning on the domain. Maximum of 4 clocks (N = 0 to 3) are supported. - asbN: Clocks required by asynchronous bridges (ASB) present in @@ -38,6 +41,7 @@ Example: compatible = "samsung,exynos4210-pd"; reg = <0x10023C00 0x10>; #power-domain-cells = <0>; + label = "LCD0"; }; mfc_pd: power-domain@10044060 { @@ -46,6 +50,7 @@ Example: clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MOUT_USER_ACLK333>; clock-names = "oscclk", "clk0"; #power-domain-cells = <0>; + label = "MFC"; }; See Documentation/devicetree/bindings/power/power_domain.txt for description diff --git a/Documentation/devicetree/bindings/power/power_domain.txt b/Documentation/devicetree/bindings/power/power_domain.txt index 025b5e7df61c..14bd9e945ff6 100644 --- a/Documentation/devicetree/bindings/power/power_domain.txt +++ b/Documentation/devicetree/bindings/power/power_domain.txt @@ -29,6 +29,17 @@ Optional properties: specified by this binding. More details about power domain specifier are available in the next section. +- domain-idle-states : A phandle of an idle-state that shall be soaked into a + generic domain power state. The idle state definitions are + compatible with domain-idle-state specified in [1]. phandles + that are not compatible with domain-idle-state will be + ignored. + The domain-idle-state property reflects the idle state of this PM domain and + not the idle states of the devices or sub-domains in the PM domain. Devices + and sub-domains have their own idle-states independent of the parent + domain's idle states. In the absence of this property, the domain would be + considered as capable of being powered-on or powered-off. + Example: power: power-controller@12340000 { @@ -59,6 +70,38 @@ The nodes above define two power controllers: 'parent' and 'child'. Domains created by the 'child' power controller are subdomains of '0' power domain provided by the 'parent' power controller. +Example 3: + parent: power-controller@12340000 { + compatible = "foo,power-controller"; + reg = <0x12340000 0x1000>; + #power-domain-cells = <0>; + domain-idle-states = <&DOMAIN_RET>, <&DOMAIN_PWR_DN>; + }; + + child: power-controller@12341000 { + compatible = "foo,power-controller"; + reg = <0x12341000 0x1000>; + power-domains = <&parent>; + #power-domain-cells = <0>; + domain-idle-states = <&DOMAIN_PWR_DN>; + }; + + DOMAIN_RET: state@0 { + compatible = "domain-idle-state"; + reg = <0x0>; + entry-latency-us = <1000>; + exit-latency-us = <2000>; + min-residency-us = <10000>; + }; + + DOMAIN_PWR_DN: state@1 { + compatible = "domain-idle-state"; + reg = <0x1>; + entry-latency-us = <5000>; + exit-latency-us = <8000>; + min-residency-us = <7000>; + }; + ==PM domain consumers== Required properties: @@ -76,3 +119,5 @@ Example: The node above defines a typical PM domain consumer device, which is located inside a PM domain with index 0 of a power controller represented by a node with the label "power". + +[1]. Documentation/devicetree/bindings/power/domain-idle-state.txt diff --git a/Documentation/devicetree/bindings/power/renesas,apmu.txt b/Documentation/devicetree/bindings/power/renesas,apmu.txt new file mode 100644 index 000000000000..84404c9edff7 --- /dev/null +++ b/Documentation/devicetree/bindings/power/renesas,apmu.txt @@ -0,0 +1,31 @@ +DT bindings for the Renesas Advanced Power Management Unit + +Renesas R-Car line of SoCs utilize one or more APMU hardware units +for CPU core power domain control including SMP boot and CPU Hotplug. + +Required properties: + +- compatible: Should be "renesas,<soctype>-apmu", "renesas,apmu" as fallback. + Examples with soctypes are: + - "renesas,r8a7790-apmu" (R-Car H2) + - "renesas,r8a7791-apmu" (R-Car M2-W) + - "renesas,r8a7792-apmu" (R-Car V2H) + - "renesas,r8a7793-apmu" (R-Car M2-N) + - "renesas,r8a7794-apmu" (R-Car E2) + +- reg: Base address and length of the I/O registers used by the APMU. + +- cpus: This node contains a list of CPU cores, which should match the order + of CPU cores used by the WUPCR and PSTR registers in the Advanced Power + Management Unit section of the device's datasheet. + + +Example: + +This shows the r8a7791 APMU that can control CPU0 and CPU1. + + apmu@e6152000 { + compatible = "renesas,r8a7791-apmu", "renesas,apmu"; + reg = <0 0xe6152000 0 0x188>; + cpus = <&cpu0 &cpu1>; + }; diff --git a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt new file mode 100644 index 000000000000..d91715bc8d52 --- /dev/null +++ b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt @@ -0,0 +1,51 @@ +DT bindings for the Renesas R-Car (RZ/G) System Controller + +== System Controller Node == + +The R-Car (RZ/G) System Controller provides power management for the CPU cores +and various coprocessors. + +Required properties: + - compatible: Must contain exactly one of the following: + - "renesas,r8a7743-sysc" (RZ/G1M) + - "renesas,r8a7745-sysc" (RZ/G1E) + - "renesas,r8a7779-sysc" (R-Car H1) + - "renesas,r8a7790-sysc" (R-Car H2) + - "renesas,r8a7791-sysc" (R-Car M2-W) + - "renesas,r8a7792-sysc" (R-Car V2H) + - "renesas,r8a7793-sysc" (R-Car M2-N) + - "renesas,r8a7794-sysc" (R-Car E2) + - "renesas,r8a7795-sysc" (R-Car H3) + - "renesas,r8a7796-sysc" (R-Car M3-W) + - reg: Address start and address range for the device. + - #power-domain-cells: Must be 1. + + +Example: + + sysc: system-controller@e6180000 { + compatible = "renesas,r8a7791-sysc"; + reg = <0 0xe6180000 0 0x0200>; + #power-domain-cells = <1>; + }; + + +== PM Domain Consumers == + +Devices residing in a power area must refer to that power area, as documented +by the generic PM domain bindings in +Documentation/devicetree/bindings/power/power_domain.txt. + +Required properties: + - power-domains: A phandle and symbolic PM domain specifier, as defined in + <dt-bindings/power/r8a77*-sysc.h>. + + +Example: + + L2_CA15: cache-controller@0 { + compatible = "cache"; + power-domains = <&sysc R8A7791_PD_CA15_SCU>; + cache-unified; + cache-level = <2>; + }; diff --git a/Documentation/devicetree/bindings/power/reset/axxia-reset.txt b/Documentation/devicetree/bindings/power/reset/axxia-reset.txt new file mode 100644 index 000000000000..47e720d249d2 --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/axxia-reset.txt @@ -0,0 +1,20 @@ +Axxia Restart Driver + +This driver can do reset of the Axxia SoC. It uses the registers in the syscon +block to initiate a chip reset. + +Required Properties: + -compatible: "lsi,axm55xx-reset" + -syscon: phandle to the syscon node. + +Example: + + syscon: syscon@2010030000 { + compatible = "lsi,axxia-syscon", "syscon"; + reg = <0x20 0x10030000 0 0x2000>; + }; + + reset: reset@2010031000 { + compatible = "lsi,axm55xx-reset"; + syscon = <&syscon>; + }; diff --git a/Documentation/devicetree/bindings/power/reset/brcm,bcm21664-resetmgr.txt b/Documentation/devicetree/bindings/power/reset/brcm,bcm21664-resetmgr.txt new file mode 100644 index 000000000000..93f31ca1ef4b --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/brcm,bcm21664-resetmgr.txt @@ -0,0 +1,14 @@ +Broadcom Kona Family Reset Manager +---------------------------------- + +The reset manager is used on the Broadcom BCM21664 SoC. + +Required properties: + - compatible: brcm,bcm21664-resetmgr + - reg: memory address & range + +Example: + brcm,resetmgr@35001f00 { + compatible = "brcm,bcm21664-resetmgr"; + reg = <0x35001f00 0x24>; + }; diff --git a/Documentation/devicetree/bindings/power/reset/gemini-poweroff.txt b/Documentation/devicetree/bindings/power/reset/gemini-poweroff.txt new file mode 100644 index 000000000000..7fec3e100214 --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/gemini-poweroff.txt @@ -0,0 +1,17 @@ +* Device-Tree bindings for Cortina Systems Gemini Poweroff + +This is a special IP block in the Cortina Gemini SoC that only +deals with different ways to power the system down. + +Required properties: +- compatible: should be "cortina,gemini-power-controller" +- reg: should contain the physical memory base and size +- interrupts: should contain the power management interrupt + +Example: + +power-controller@4b000000 { + compatible = "cortina,gemini-power-controller"; + reg = <0x4b000000 0x100>; + interrupts = <26 IRQ_TYPE_EDGE_FALLING>; +}; diff --git a/Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt b/Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt new file mode 100644 index 000000000000..e62d53d844cc --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt @@ -0,0 +1,36 @@ +Driver a GPIO line that can be used to turn the power off. + +The driver supports both level triggered and edge triggered power off. +At driver load time, the driver will request the given gpio line and +install a handler to power off the system. If the optional properties +'input' is not found, the GPIO line will be driven in the inactive +state. Otherwise its configured as an input. + +When the power-off handler is called, the gpio is configured as an +output, and drive active, so triggering a level triggered power off +condition. This will also cause an inactive->active edge condition, so +triggering positive edge triggered power off. After a delay of 100ms, +the GPIO is set to inactive, thus causing an active->inactive edge, +triggering negative edge triggered power off. After another 100ms +delay the GPIO is driver active again. If the power is still on and +the CPU still running after a 3000ms delay, a WARN_ON(1) is emitted. + +Required properties: +- compatible : should be "gpio-poweroff". +- gpios : The GPIO to set high/low, see "gpios property" in + Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be + low to power down the board set it to "Active Low", otherwise set + gpio to "Active High". + +Optional properties: +- input : Initially configure the GPIO line as an input. Only reconfigure + it to an output when the power-off handler is called. If this optional + property is not specified, the GPIO is initialized as an output in its + inactive state. + +Examples: + +gpio-poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio 4 0>; +}; diff --git a/Documentation/devicetree/bindings/power/reset/gpio-restart.txt b/Documentation/devicetree/bindings/power/reset/gpio-restart.txt new file mode 100644 index 000000000000..af3701bc15c4 --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/gpio-restart.txt @@ -0,0 +1,54 @@ +Drive a GPIO line that can be used to restart the system from a restart +handler. + +This binding supports level and edge triggered reset. At driver load +time, the driver will request the given gpio line and install a restart +handler. If the optional properties 'open-source' is not found, the GPIO line +will be driven in the inactive state. Otherwise its not driven until +the restart is initiated. + +When the system is restarted, the restart handler will be invoked in +priority order. The gpio is configured as an output, and driven active, +triggering a level triggered reset condition. This will also cause an +inactive->active edge condition, triggering positive edge triggered +reset. After a delay specified by active-delay, the GPIO is set to +inactive, thus causing an active->inactive edge, triggering negative edge +triggered reset. After a delay specified by inactive-delay, the GPIO +is driven active again. After a delay specified by wait-delay, the +restart handler completes allowing other restart handlers to be attempted. + +Required properties: +- compatible : should be "gpio-restart". +- gpios : The GPIO to set high/low, see "gpios property" in + Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be + low to reset the board set it to "Active Low", otherwise set + gpio to "Active High". + +Optional properties: +- open-source : Treat the GPIO as being open source and defer driving + it to when the restart is initiated. If this optional property is not + specified, the GPIO is initialized as an output in its inactive state. +- priority : A priority ranging from 0 to 255 (default 128) according to + the following guidelines: + 0: Restart handler of last resort, with limited restart + capabilities + 128: Default restart handler; use if no other restart handler is + expected to be available, and/or if restart functionality is + sufficient to restart the entire system + 255: Highest priority restart handler, will preempt all other + restart handlers +- active-delay: Delay (default 100) to wait after driving gpio active [ms] +- inactive-delay: Delay (default 100) to wait after driving gpio inactive [ms] +- wait-delay: Delay (default 3000) to wait after completing restart + sequence [ms] + +Examples: + +gpio-restart { + compatible = "gpio-restart"; + gpios = <&gpio 4 0>; + priority = <128>; + active-delay = <100>; + inactive-delay = <100>; + wait-delay = <3000>; +}; diff --git a/Documentation/devicetree/bindings/power/reset/imx-snvs-poweroff.txt b/Documentation/devicetree/bindings/power/reset/imx-snvs-poweroff.txt new file mode 100644 index 000000000000..dc7c9bad63ea --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/imx-snvs-poweroff.txt @@ -0,0 +1,23 @@ +i.mx6 Poweroff Driver + +SNVS_LPCR in SNVS module can power off the whole system by pull +PMIC_ON_REQ low if PMIC_ON_REQ is connected with external PMIC. +If you don't want to use PMIC_ON_REQ as power on/off control, +please set status='disabled' to disable this driver. + +Required Properties: +-compatible: "fsl,sec-v4.0-poweroff" +-reg: Specifies the physical address of the SNVS_LPCR register + +Example: + snvs@020cc000 { + compatible = "fsl,sec-v4.0-mon", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x020cc000 0x4000>; + ..... + snvs_poweroff: snvs-poweroff@38 { + compatible = "fsl,sec-v4.0-poweroff"; + reg = <0x38 0x4>; + }; + } diff --git a/Documentation/devicetree/bindings/power/reset/msm-poweroff.txt b/Documentation/devicetree/bindings/power/reset/msm-poweroff.txt new file mode 100644 index 000000000000..ce44ad357565 --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/msm-poweroff.txt @@ -0,0 +1,17 @@ +MSM Restart Driver + +A power supply hold (ps-hold) bit is set to power the msm chipsets. +Clearing that bit allows us to restart/poweroff. The difference +between poweroff and restart is determined by unique power manager IC +settings. + +Required Properties: +-compatible: "qcom,pshold" +-reg: Specifies the physical address of the ps-hold register + +Example: + + restart@fc4ab000 { + compatible = "qcom,pshold"; + reg = <0xfc4ab000 0x4>; + }; diff --git a/Documentation/devicetree/bindings/power/reset/qnap-poweroff.txt b/Documentation/devicetree/bindings/power/reset/qnap-poweroff.txt new file mode 100644 index 000000000000..c363d7173129 --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/qnap-poweroff.txt @@ -0,0 +1,15 @@ +* QNAP Power Off + +QNAP NAS devices have a microcontroller controlling the main power +supply. This microcontroller is connected to UART1 of the Kirkwood and +Orion5x SoCs. Sending the character 'A', at 19200 baud, tells the +microcontroller to turn the power off. + +Synology NAS devices use a similar scheme, but a different baud rate, +9600, and a different character, '1'. + +Required Properties: +- compatible: Should be "qnap,power-off" or "synology,power-off" + +- reg: Address and length of the register set for UART1 +- clocks: tclk clock diff --git a/Documentation/devicetree/bindings/power/reset/reboot-mode.txt b/Documentation/devicetree/bindings/power/reset/reboot-mode.txt new file mode 100644 index 000000000000..de34f27d509e --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/reboot-mode.txt @@ -0,0 +1,25 @@ +Generic reboot mode core map driver + +This driver get reboot mode arguments and call the write +interface to store the magic value in special register +or ram. Then the bootloader can read it and take different +action according to the argument stored. + +All mode properties are vendor specific, it is a indication to tell +the bootloader what to do when the system reboots, and should be named +as mode-xxx = <magic> (xxx is mode name, magic should be a none-zero value). + +For example modes common on Android platform: +- mode-normal: Normal reboot mode, system reboot with command "reboot". +- mode-recovery: Android Recovery mode, it is a mode to format the device or update a new image. +- mode-bootloader: Android fastboot mode, it's a mode to re-flash partitions on the Android based device. +- mode-loader: A bootloader mode, it's a mode used to download image on Rockchip platform, + usually used in development. + +Example: + reboot-mode { + mode-normal = <BOOT_NORMAL>; + mode-recovery = <BOOT_RECOVERY>; + mode-bootloader = <BOOT_FASTBOOT>; + mode-loader = <BOOT_BL_DOWNLOAD>; + } diff --git a/Documentation/devicetree/bindings/power/reset/restart-poweroff.txt b/Documentation/devicetree/bindings/power/reset/restart-poweroff.txt new file mode 100644 index 000000000000..5776e684afda --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/restart-poweroff.txt @@ -0,0 +1,8 @@ +* Restart Power Off + +Buffalo Linkstation LS-XHL and LS-CHLv2, and other devices power off +by restarting and letting u-boot keep hold of the machine until the +user presses a button. + +Required Properties: +- compatible: Should be "restart-poweroff" diff --git a/Documentation/devicetree/bindings/power/reset/st-reset.txt b/Documentation/devicetree/bindings/power/reset/st-reset.txt index 809af54f02f3..83734dc3a389 100644 --- a/Documentation/devicetree/bindings/power/reset/st-reset.txt +++ b/Documentation/devicetree/bindings/power/reset/st-reset.txt @@ -1,11 +1,12 @@ *Device-Tree bindings for ST SW reset functionality Required properties: -- compatible: should be "st,<chip>-restart". +- compatible: should be "stih407-restart". - st,syscfg: should be a phandle of the syscfg node. Example node: restart { - compatible = "st,stih416-restart"; - st,syscfg = <&syscfg_sbc>; + compatible = "st,stih407-restart"; + st,syscfg = <&syscfg_sbc_reg>; + status = "okay"; }; diff --git a/Documentation/devicetree/bindings/power/reset/syscon-poweroff.txt b/Documentation/devicetree/bindings/power/reset/syscon-poweroff.txt index 1e2546f8b08a..022ed1f3bc80 100644 --- a/Documentation/devicetree/bindings/power/reset/syscon-poweroff.txt +++ b/Documentation/devicetree/bindings/power/reset/syscon-poweroff.txt @@ -3,13 +3,20 @@ Generic SYSCON mapped register poweroff driver This is a generic poweroff driver using syscon to map the poweroff register. The poweroff is generally performed with a write to the poweroff register defined by the register map pointed by syscon reference plus the offset -with the mask defined in the poweroff node. +with the value and mask defined in the poweroff node. Required properties: - compatible: should contain "syscon-poweroff" - regmap: this is phandle to the register map node - offset: offset in the register map for the poweroff register (in bytes) -- mask: the poweroff value written to the poweroff register (32 bit access) +- value: the poweroff value written to the poweroff register (32 bit access) + +Optional properties: +- mask: update only the register bits defined by the mask (32 bit) + +Legacy usage: +If a node doesn't contain a value property but contains a mask property, the +mask property is used as the value. Default will be little endian mode, 32 bit access only. diff --git a/Documentation/devicetree/bindings/power/reset/syscon-reboot-mode.txt b/Documentation/devicetree/bindings/power/reset/syscon-reboot-mode.txt new file mode 100644 index 000000000000..f7ce1d8af04a --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/syscon-reboot-mode.txt @@ -0,0 +1,35 @@ +SYSCON reboot mode driver + +This driver gets reboot mode magic value form reboot-mode driver +and stores it in a SYSCON mapped register. Then the bootloader +can read it and take different action according to the magic +value stored. + +This DT node should be represented as a sub-node of a "syscon", "simple-mfd" +node. + +Required properties: +- compatible: should be "syscon-reboot-mode" +- offset: offset in the register map for the storage register (in bytes) + +Optional property: +- mask: bits mask of the bits in the register to store the reboot mode magic value, + default set to 0xffffffff if missing. + +The rest of the properties should follow the generic reboot-mode description +found in reboot-mode.txt + +Example: + pmu: pmu@20004000 { + compatible = "rockchip,rk3066-pmu", "syscon", "simple-mfd"; + reg = <0x20004000 0x100>; + + reboot-mode { + compatible = "syscon-reboot-mode"; + offset = <0x40>; + mode-normal = <BOOT_NORMAL>; + mode-recovery = <BOOT_RECOVERY>; + mode-bootloader = <BOOT_FASTBOOT>; + mode-loader = <BOOT_BL_DOWNLOAD>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt index b8627e763dba..43c21fb04564 100644 --- a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt +++ b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt @@ -32,11 +32,17 @@ SoC is on the same page. Required properties: - compatible: should be one of: - "rockchip,rk3188-io-voltage-domain" for rk3188 + - "rockchip,rk3228-io-voltage-domain" for rk3228 - "rockchip,rk3288-io-voltage-domain" for rk3288 + - "rockchip,rk3328-io-voltage-domain" for rk3328 - "rockchip,rk3368-io-voltage-domain" for rk3368 - "rockchip,rk3368-pmu-io-voltage-domain" for rk3368 pmu-domains -- rockchip,grf: phandle to the syscon managing the "general register files" + - "rockchip,rk3399-io-voltage-domain" for rk3399 + - "rockchip,rk3399-pmu-io-voltage-domain" for rk3399 pmu-domains +Deprecated properties: +- rockchip,grf: phandle to the syscon managing the "general register files" + Systems should move the io-domains to a sub-node of the grf simple-mfd. You specify supplies using the standard regulator bindings by including a phandle the relevant regulator. All specified supplies must be able @@ -54,6 +60,12 @@ Possible supplies for rk3188: - vccio1-supply: The supply connected to VCCIO1. Sometimes also labeled VCCIO1 and VCCIO2. +Possible supplies for rk3228: +- vccio1-supply: The supply connected to VCCIO1. +- vccio2-supply: The supply connected to VCCIO2. +- vccio3-supply: The supply connected to VCCIO3. +- vccio4-supply: The supply connected to VCCIO4. + Possible supplies for rk3288: - audio-supply: The supply connected to APIO4_VDD. - bb-supply: The supply connected to APIO5_VDD. @@ -79,6 +91,15 @@ Possible supplies for rk3368 pmu-domains: - pmu-supply: The supply connected to PMUIO_VDD. - vop-supply: The supply connected to LCDC_VDD. +Possible supplies for rk3399: +- bt656-supply: The supply connected to APIO2_VDD. +- audio-supply: The supply connected to APIO5_VDD. +- sdmmc-supply: The supply connected to SDMMC0_VDD. +- gpio1830 The supply connected to APIO4_VDD. + +Possible supplies for rk3399 pmu-domains: +- pmu1830-supply:The supply connected to PMUIO2_VDD. + Example: io-domains { diff --git a/Documentation/devicetree/bindings/power/supply/ab8500/btemp.txt b/Documentation/devicetree/bindings/power/supply/ab8500/btemp.txt new file mode 100644 index 000000000000..0ba1bcc7f33a --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/ab8500/btemp.txt @@ -0,0 +1,16 @@ +=== AB8500 Battery Temperature Monitor Driver === + +The properties below describes the node for btemp driver. + +Required Properties: +- compatible = Shall be: "stericsson,ab8500-btemp" +- battery = Shall be battery specific information + + Example: + ab8500_btemp { + compatible = "stericsson,ab8500-btemp"; + battery = <&ab8500_battery>; + }; + +For information on battery specific node, Ref: +Documentation/devicetree/bindings/power_supply/ab8500/fg.txt diff --git a/Documentation/devicetree/bindings/power/supply/ab8500/chargalg.txt b/Documentation/devicetree/bindings/power/supply/ab8500/chargalg.txt new file mode 100644 index 000000000000..ef5328371122 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/ab8500/chargalg.txt @@ -0,0 +1,16 @@ +=== AB8500 Charging Algorithm Driver === + +The properties below describes the node for chargalg driver. + +Required Properties: +- compatible = Shall be: "stericsson,ab8500-chargalg" +- battery = Shall be battery specific information + +Example: +ab8500_chargalg { + compatible = "stericsson,ab8500-chargalg"; + battery = <&ab8500_battery>; +}; + +For information on battery specific node, Ref: +Documentation/devicetree/bindings/power_supply/ab8500/fg.txt diff --git a/Documentation/devicetree/bindings/power/supply/ab8500/charger.txt b/Documentation/devicetree/bindings/power/supply/ab8500/charger.txt new file mode 100644 index 000000000000..6bdbb08ea9e0 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/ab8500/charger.txt @@ -0,0 +1,25 @@ +=== AB8500 Charger Driver === + +Required Properties: +- compatible = Shall be "stericsson,ab8500-charger" +- battery = Shall be battery specific information + Example: + ab8500_charger { + compatible = "stericsson,ab8500-charger"; + battery = <&ab8500_battery>; + }; + +- vddadc-supply: Supply for USB and Main charger + Example: + ab8500-charger { + vddadc-supply = <&ab8500_ldo_tvout_reg>; + } +- autopower_cfg: + Boolean value depicting the presence of 'automatic poweron after powerloss' + Example: + ab8500-charger { + autopower_cfg; + }; + +For information on battery specific node, Ref: +Documentation/devicetree/bindings/power_supply/ab8500/fg.txt diff --git a/Documentation/devicetree/bindings/power/supply/ab8500/fg.txt b/Documentation/devicetree/bindings/power/supply/ab8500/fg.txt new file mode 100644 index 000000000000..ccafcb9112fb --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/ab8500/fg.txt @@ -0,0 +1,58 @@ +=== AB8500 Fuel Gauge Driver === + +AB8500 is a mixed signal multimedia and power management +device comprising: power and energy-management-module, +wall-charger, usb-charger, audio codec, general purpose adc, +tvout, clock management and sim card interface. + +Fuelgauge support is part of energy-management-modules, other +components of this module are: +main-charger, usb-combo-charger and battery-temperature-monitoring. + +The properties below describes the node for fuelgauge driver. + +Required Properties: +- compatible = This shall be: "stericsson,ab8500-fg" +- battery = Shall be battery specific information + Example: + ab8500_fg { + compatible = "stericsson,ab8500-fg"; + battery = <&ab8500_battery>; + }; + +dependent node: + ab8500_battery: ab8500_battery { + }; + This node will provide information on 'thermistor interface' and + 'battery technology type' used. + +Properties of this node are: +thermistor-on-batctrl: + A boolean value indicating thermistor interface to battery + + Note: + 'btemp' and 'batctrl' are the pins interfaced for battery temperature + measurement, 'btemp' signal is used when NTC(negative temperature + coefficient) resister is interfaced external to battery whereas + 'batctrl' pin is used when NTC resister is internal to battery. + + Example: + ab8500_battery: ab8500_battery { + thermistor-on-batctrl; + }; + indicates: NTC resister is internal to battery, 'batctrl' is used + for thermal measurement. + + The absence of property 'thermal-on-batctrl' indicates + NTC resister is external to battery and 'btemp' signal is used + for thermal measurement. + +battery-type: + This shall be the battery manufacturing technology type, + allowed types are: + "UNKNOWN" "NiMH" "LION" "LIPO" "LiFe" "NiCd" "LiMn" + Example: + ab8500_battery: ab8500_battery { + stericsson,battery-type = "LIPO"; + } + diff --git a/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt b/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt new file mode 100644 index 000000000000..de78d761ce44 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt @@ -0,0 +1,48 @@ +Device-Tree bindings for charger of Active-semi ACT8945A Multi-Function Device + +Required properties: + - compatible: "active-semi,act8945a-charger". + - active-semi,chglev-gpios: charge current level phandle with args + as described in ../gpio/gpio.txt. + - active-semi,lbo-gpios: specify the low battery voltage detect phandle + with args as as described in ../gpio/gpio.txt. + - interrupts: <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. + - interrupt-parent: the phandle for the interrupt controller that + services interrupts for this device. + +Optional properties: + - active-semi,input-voltage-threshold-microvolt: unit: mV; + Specifies the charger's input over-voltage threshold value; + The value can be: 6600, 7000, 7500, 8000; default: 6600 + - active-semi,precondition-timeout: unit: minutes; + Specifies the charger's PRECONDITION safety timer setting value; + The value can be: 40, 60, 80, 0; If 0, it means to disable this timer; + default: 40. + - active-semi,total-timeout: unit: hours; + Specifies the charger's total safety timer setting value; + The value can be: 3, 4, 5, 0; If 0, it means to disable this timer; + default: 3. + +Example: + pmic@5b { + compatible = "active-semi,act8945a"; + reg = <0x5b>; + status = "okay"; + + charger { + compatible = "active-semi,act8945a-charger"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_charger_chglev &pinctrl_charger_lbo &pinctrl_charger_irq>; + interrupt-parent = <&pioA>; + interrupts = <45 GPIO_ACTIVE_LOW>; + + active-semi,chglev-gpios = <&pioA 12 GPIO_ACTIVE_HIGH>; + active-semi,lbo-gpios = <&pioA 72 GPIO_ACTIVE_LOW>; + active-semi,input-voltage-threshold-microvolt = <6600>; + active-semi,precondition-timeout = <40>; + active-semi,total-timeout = <3>; + status = "okay"; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/axp20x_ac_power.txt b/Documentation/devicetree/bindings/power/supply/axp20x_ac_power.txt new file mode 100644 index 000000000000..826e8a879121 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/axp20x_ac_power.txt @@ -0,0 +1,22 @@ +AXP20X and AXP22X PMICs' AC power supply + +Required Properties: + - compatible: One of: + "x-powers,axp202-ac-power-supply" + "x-powers,axp221-ac-power-supply" + +This node is a subnode of the axp20x PMIC. + +The AXP20X can read the current current and voltage supplied by AC by +reading ADC channels from the AXP20X ADC. + +The AXP22X is only able to tell if an AC power supply is present and +usable. + +Example: + +&axp209 { + ac_power_supply: ac-power-supply { + compatible = "x-powers,axp202-ac-power-supply"; + }; +}; diff --git a/Documentation/devicetree/bindings/power/supply/axp20x_battery.txt b/Documentation/devicetree/bindings/power/supply/axp20x_battery.txt new file mode 100644 index 000000000000..c24886676a60 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/axp20x_battery.txt @@ -0,0 +1,20 @@ +AXP20x and AXP22x battery power supply + +Required Properties: + - compatible, one of: + "x-powers,axp209-battery-power-supply" + "x-powers,axp221-battery-power-supply" + +This node is a subnode of the axp20x/axp22x PMIC. + +The AXP20X and AXP22X can read the battery voltage, charge and discharge +currents of the battery by reading ADC channels from the AXP20X/AXP22X +ADC. + +Example: + +&axp209 { + battery_power_supply: battery-power-supply { + compatible = "x-powers,axp209-battery-power-supply"; + } +}; diff --git a/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt b/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt new file mode 100644 index 000000000000..ba8d35f66cbe --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt @@ -0,0 +1,40 @@ +AXP20x USB power supply + +Required Properties: +-compatible: One of: "x-powers,axp202-usb-power-supply" + "x-powers,axp221-usb-power-supply" + "x-powers,axp223-usb-power-supply" + +The AXP223 PMIC shares most of its behaviour with the AXP221 but has slight +variations such as the former being able to set the VBUS power supply max +current to 100mA, unlike the latter. + +This node is a subnode of the axp20x PMIC. + +Example: + +axp209: pmic@34 { + compatible = "x-powers,axp209"; + reg = <0x34>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + + regulators { + x-powers,dcdc-freq = <1500>; + + vdd_cpu: dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1450000>; + regulator-name = "vdd-cpu"; + }; + + ... + }; + + usb-power-supply: usb-power-supply { + compatible = "x-powers,axp202-usb-power-supply"; + }; +}; diff --git a/Documentation/devicetree/bindings/power/supply/battery.txt b/Documentation/devicetree/bindings/power/supply/battery.txt new file mode 100644 index 000000000000..f4d3b4a10b43 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/battery.txt @@ -0,0 +1,57 @@ +Battery Characteristics + +The devicetree battery node provides static battery characteristics. +In smart batteries, these are typically stored in non-volatile memory +on a fuel gauge chip. The battery node should be used where there is +no appropriate non-volatile memory, or it is unprogrammed/incorrect. + +Upstream dts files should not include battery nodes, unless the battery +represented cannot easily be replaced in the system by one of a +different type. This prevents unpredictable, potentially harmful, +behavior should a replacement that changes the battery type occur +without a corresponding update to the dtb. + +Required Properties: + - compatible: Must be "simple-battery" + +Optional Properties: + - voltage-min-design-microvolt: drained battery voltage + - energy-full-design-microwatt-hours: battery design energy + - charge-full-design-microamp-hours: battery design capacity + - precharge-current-microamp: current for pre-charge phase + - charge-term-current-microamp: current for charge termination phase + - constant-charge-current-max-microamp: maximum constant input current + - constant-charge-voltage-max-microvolt: maximum constant input voltage + +Battery properties are named, where possible, for the corresponding +elements in enum power_supply_property, defined in +https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/include/linux/power_supply.h + +Batteries must be referenced by chargers and/or fuel-gauges +using a phandle. The phandle's property should be named +"monitored-battery". + +Example: + + bat: battery { + compatible = "simple-battery"; + voltage-min-design-microvolt = <3200000>; + energy-full-design-microwatt-hours = <5290000>; + charge-full-design-microamp-hours = <1430000>; + precharge-current-microamp = <256000>; + charge-term-current-microamp = <128000>; + constant-charge-current-max-microamp = <900000>; + constant-charge-voltage-max-microvolt = <4200000>; + }; + + charger: charger@11 { + .... + monitored-battery = <&bat>; + ... + }; + + fuel_gauge: fuel-gauge@22 { + .... + monitored-battery = <&bat>; + ... + }; diff --git a/Documentation/devicetree/bindings/power/bq2415x.txt b/Documentation/devicetree/bindings/power/supply/bq2415x.txt index d0327f0b59ad..d0327f0b59ad 100644 --- a/Documentation/devicetree/bindings/power/bq2415x.txt +++ b/Documentation/devicetree/bindings/power/supply/bq2415x.txt diff --git a/Documentation/devicetree/bindings/power/bq24257.txt b/Documentation/devicetree/bindings/power/supply/bq24257.txt index d693702c9c1e..d693702c9c1e 100644 --- a/Documentation/devicetree/bindings/power/bq24257.txt +++ b/Documentation/devicetree/bindings/power/supply/bq24257.txt diff --git a/Documentation/devicetree/bindings/power/bq25890.txt b/Documentation/devicetree/bindings/power/supply/bq25890.txt index c9dd17d142ad..c9dd17d142ad 100644 --- a/Documentation/devicetree/bindings/power/bq25890.txt +++ b/Documentation/devicetree/bindings/power/supply/bq25890.txt diff --git a/Documentation/devicetree/bindings/power/supply/bq27xxx.txt b/Documentation/devicetree/bindings/power/supply/bq27xxx.txt new file mode 100644 index 000000000000..6858e1a804ad --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/bq27xxx.txt @@ -0,0 +1,53 @@ +TI BQ27XXX fuel gauge family + +Required properties: +- compatible: contains one of the following: + * "ti,bq27200" - BQ27200 + * "ti,bq27210" - BQ27210 + * "ti,bq27500" - deprecated, use revision specific property below + * "ti,bq27510" - deprecated, use revision specific property below + * "ti,bq27520" - deprecated, use revision specific property below + * "ti,bq27500-1" - BQ27500/1 + * "ti,bq27510g1" - BQ27510-g1 + * "ti,bq27510g2" - BQ27510-g2 + * "ti,bq27510g3" - BQ27510-g3 + * "ti,bq27520g1" - BQ27520-g1 + * "ti,bq27520g2" - BQ27520-g2 + * "ti,bq27520g3" - BQ27520-g3 + * "ti,bq27520g4" - BQ27520-g4 + * "ti,bq27530" - BQ27530 + * "ti,bq27531" - BQ27531 + * "ti,bq27541" - BQ27541 + * "ti,bq27542" - BQ27542 + * "ti,bq27546" - BQ27546 + * "ti,bq27742" - BQ27742 + * "ti,bq27545" - BQ27545 + * "ti,bq27421" - BQ27421 + * "ti,bq27425" - BQ27425 + * "ti,bq27441" - BQ27441 + * "ti,bq27621" - BQ27621 +- reg: integer, I2C address of the fuel gauge. + +Optional properties: +- monitored-battery: phandle of battery characteristics node + The fuel gauge uses the following battery properties: + + energy-full-design-microwatt-hours + + charge-full-design-microamp-hours + + voltage-min-design-microvolt + Both or neither of the *-full-design-*-hours properties must be set. + See Documentation/devicetree/bindings/power/supply/battery.txt + +Example: + + bat: battery { + compatible = "simple-battery"; + voltage-min-design-microvolt = <3200000>; + energy-full-design-microwatt-hours = <5290000>; + charge-full-design-microamp-hours = <1430000>; + }; + + bq27510g3: fuel-gauge@55 { + compatible = "ti,bq27510g3"; + reg = <0x55>; + monitored-battery = <&bat>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/charger-manager.txt b/Documentation/devicetree/bindings/power/supply/charger-manager.txt new file mode 100644 index 000000000000..ec4fe9de3137 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/charger-manager.txt @@ -0,0 +1,81 @@ +charger-manager bindings +~~~~~~~~~~~~~~~~~~~~~~~~ + +Required properties : + - compatible : "charger-manager" + - <>-supply : for regulator consumer + - cm-num-chargers : number of chargers + - cm-chargers : name of chargers + - cm-fuel-gauge : name of battery fuel gauge + - subnode <regulator> : + - cm-regulator-name : name of charger regulator + - subnode <cable> : + - cm-cable-name : name of charger cable + - cm-cable-extcon : name of extcon dev +(optional) - cm-cable-min : minimum current of cable +(optional) - cm-cable-max : maximum current of cable + +Optional properties : + - cm-name : charger manager's name (default : "battery") + - cm-poll-mode : polling mode (enum polling_modes) + - cm-poll-interval : polling interval + - cm-battery-stat : battery status (enum data_source) + - cm-fullbatt-* : data for full battery checking + - cm-thermal-zone : name of external thermometer's thermal zone + - cm-battery-* : threshold battery temperature for charging + -cold : critical cold temperature of battery for charging + -cold-in-minus : flag that cold temperature is in minus degrees + -hot : critical hot temperature of battery for charging + -temp-diff : temperature difference to allow recharging + - cm-dis/charging-max = limits of charging duration + +Example : + charger-manager@0 { + compatible = "charger-manager"; + chg-reg-supply = <&charger_regulator>; + + cm-name = "battery"; + /* Always polling ON : 30s */ + cm-poll-mode = <1>; + cm-poll-interval = <30000>; + + cm-fullbatt-vchkdrop-ms = <30000>; + cm-fullbatt-vchkdrop-volt = <150000>; + cm-fullbatt-soc = <100>; + + cm-battery-stat = <3>; + + cm-num-chargers = <3>; + cm-chargers = "charger0", "charger1", "charger2"; + + cm-fuel-gauge = "fuelgauge0"; + + cm-thermal-zone = "thermal_zone.1" + /* in deci centigrade */ + cm-battery-cold = <50>; + cm-battery-cold-in-minus; + cm-battery-hot = <800>; + cm-battery-temp-diff = <100>; + + /* Allow charging for 5hr */ + cm-charging-max = <18000000>; + /* Allow discharging for 2hr */ + cm-discharging-max = <7200000>; + + regulator@0 { + cm-regulator-name = "chg-reg"; + cable@0 { + cm-cable-name = "USB"; + cm-cable-extcon = "extcon-dev.0"; + cm-cable-min = <475000>; + cm-cable-max = <500000>; + }; + cable@1 { + cm-cable-name = "TA"; + cm-cable-extcon = "extcon-dev.0"; + cm-cable-min = <650000>; + cm-cable-max = <675000>; + }; + }; + + }; diff --git a/Documentation/devicetree/bindings/power/supply/cpcap-battery.txt b/Documentation/devicetree/bindings/power/supply/cpcap-battery.txt new file mode 100644 index 000000000000..a04efa22da01 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/cpcap-battery.txt @@ -0,0 +1,31 @@ +Motorola CPCAP PMIC battery driver binding + +Required properties: +- compatible: Shall be "motorola,cpcap-battery" +- interrupts: Interrupt specifier for each name in interrupt-names +- interrupt-names: Should contain the following entries: + "lowbph", "lowbpl", "chrgcurr1", "battdetb" +- io-channels: IIO ADC channel specifier for each name in io-channel-names +- io-channel-names: Should contain the following entries: + "battdetb", "battp", "chg_isense", "batti" +- power-supplies: List of phandles for power-supplying devices, as + described in power_supply.txt. Typically a reference + to cpcap_charger. + +Example: + +cpcap_battery: battery { + compatible = "motorola,cpcap-battery"; + interrupts-extended = < + &cpcap 5 0 &cpcap 3 0 + &cpcap 20 0 &cpcap 54 0 + >; + interrupt-names = + "lowbph", "lowbpl", + "chrgcurr1", "battdetb"; + io-channels = <&cpcap_adc 0 &cpcap_adc 1 + &cpcap_adc 5 &cpcap_adc 6>; + io-channel-names = "battdetb", "battp", + "chg_isense", "batti"; + power-supplies = <&cpcap_charger>; +}; diff --git a/Documentation/devicetree/bindings/power/supply/cpcap-charger.txt b/Documentation/devicetree/bindings/power/supply/cpcap-charger.txt new file mode 100644 index 000000000000..80bd873c3b1d --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/cpcap-charger.txt @@ -0,0 +1,37 @@ +Motorola CPCAP PMIC battery charger binding + +Required properties: +- compatible: Shall be "motorola,mapphone-cpcap-charger" +- interrupts: Interrupt specifier for each name in interrupt-names +- interrupt-names: Should contain the following entries: + "chrg_det", "rvrs_chrg", "chrg_se1b", "se0conn", + "rvrs_mode", "chrgcurr1", "vbusvld", "battdetb" +- io-channels: IIO ADC channel specifier for each name in io-channel-names +- io-channel-names: Should contain the following entries: + "battdetb", "battp", "vbus", "chg_isense", "batti" + +Optional properties: +- mode-gpios: Optionally CPCAP charger can have a companion wireless + charge controller that is controlled with two GPIOs + that are active low. + +Example: + +cpcap_charger: charger { + compatible = "motorola,mapphone-cpcap-charger"; + interrupts-extended = < + &cpcap 13 0 &cpcap 12 0 &cpcap 29 0 &cpcap 28 0 + &cpcap 22 0 &cpcap 20 0 &cpcap 19 0 &cpcap 54 0 + >; + interrupt-names = + "chrg_det", "rvrs_chrg", "chrg_se1b", "se0conn", + "rvrs_mode", "chrgcurr1", "vbusvld", "battdetb"; + mode-gpios = <&gpio3 29 GPIO_ACTIVE_LOW + &gpio3 23 GPIO_ACTIVE_LOW>; + io-channels = <&cpcap_adc 0 &cpcap_adc 1 + &cpcap_adc 2 &cpcap_adc 5 + &cpcap_adc 6>; + io-channel-names = "battdetb", "battp", + "vbus", "chg_isense", + "batti"; +}; diff --git a/Documentation/devicetree/bindings/power/da9150-charger.txt b/Documentation/devicetree/bindings/power/supply/da9150-charger.txt index f3906663c454..f3906663c454 100644 --- a/Documentation/devicetree/bindings/power/da9150-charger.txt +++ b/Documentation/devicetree/bindings/power/supply/da9150-charger.txt diff --git a/Documentation/devicetree/bindings/power/da9150-fg.txt b/Documentation/devicetree/bindings/power/supply/da9150-fg.txt index 00236fe3ea31..00236fe3ea31 100644 --- a/Documentation/devicetree/bindings/power/da9150-fg.txt +++ b/Documentation/devicetree/bindings/power/supply/da9150-fg.txt diff --git a/Documentation/devicetree/bindings/power/supply/gpio-charger.txt b/Documentation/devicetree/bindings/power/supply/gpio-charger.txt new file mode 100644 index 000000000000..adbb5dc5b6e9 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/gpio-charger.txt @@ -0,0 +1,27 @@ +gpio-charger + +Required properties : + - compatible : "gpio-charger" + - gpios : GPIO indicating the charger presence. + See GPIO binding in bindings/gpio/gpio.txt . + - charger-type : power supply type, one of + unknown + battery + ups + mains + usb-sdp (USB standard downstream port) + usb-dcp (USB dedicated charging port) + usb-cdp (USB charging downstream port) + usb-aca (USB accessory charger adapter) + +Example: + + usb_charger: charger { + compatible = "gpio-charger"; + charger-type = "usb-sdp"; + gpios = <&gpf0 2 0 0 0>; + } + + battery { + power-supplies = <&usb_charger>; + }; diff --git a/Documentation/devicetree/bindings/power/isp1704.txt b/Documentation/devicetree/bindings/power/supply/isp1704.txt index fa3596907967..fa3596907967 100644 --- a/Documentation/devicetree/bindings/power/isp1704.txt +++ b/Documentation/devicetree/bindings/power/supply/isp1704.txt diff --git a/Documentation/devicetree/bindings/power/supply/lego_ev3_battery.txt b/Documentation/devicetree/bindings/power/supply/lego_ev3_battery.txt new file mode 100644 index 000000000000..5485633b1faa --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/lego_ev3_battery.txt @@ -0,0 +1,21 @@ +LEGO MINDSTORMS EV3 Battery +~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +LEGO MINDSTORMS EV3 has some built-in capability for monitoring the battery. +It uses 6 AA batteries or a special Li-ion rechargeable battery pack that is +detected by a key switch in the battery compartment. + +Required properties: + - compatible: Must be "lego,ev3-battery" + - io-channels: phandles to analog inputs for reading voltage and current + - io-channel-names: Must be "voltage", "current" + - rechargeable-gpios: phandle to the rechargeable battery indication gpio + +Example: + + battery { + compatible = "lego,ev3-battery"; + io-channels = <&adc 4>, <&adc 3>; + io-channel-names = "voltage", "current"; + rechargeable-gpios = <&gpio 136 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/lp8727_charger.txt b/Documentation/devicetree/bindings/power/supply/lp8727_charger.txt new file mode 100644 index 000000000000..2246bc5c874b --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/lp8727_charger.txt @@ -0,0 +1,44 @@ +Binding for TI/National Semiconductor LP8727 Charger + +Required properties: +- compatible: "ti,lp8727" +- reg: I2C slave address 27h + +Optional properties: +- interrupt-parent: interrupt controller node (see interrupt binding[0]) +- interrupts: interrupt specifier (see interrupt binding[0]) +- debounce-ms: interrupt debounce time. (u32) + +AC and USB charging parameters +- charger-type: "ac" or "usb" (string) +- eoc-level: value of 'enum lp8727_eoc_level' (u8) +- charging-current: value of 'enum lp8727_ichg' (u8) + +[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + +Example) + +lp8727@27 { + compatible = "ti,lp8727"; + reg = <0x27>; + + /* GPIO 134 is used for LP8728 interrupt pin */ + interrupt-parent = <&gpio5>; /* base = 128 */ + interrupts = <6 0x2>; /* offset = 6, falling edge type */ + + debounce-ms = <300>; + + /* AC charger: 5% EOC and 500mA charging current */ + ac { + charger-type = "ac"; + eoc-level = /bits/ 8 <0>; + charging-current = /bits/ 8 <4>; + }; + + /* USB charger: 10% EOC and 400mA charging current */ + usb { + charger-type = "usb"; + eoc-level = /bits/ 8 <1>; + charging-current = /bits/ 8 <2>; + }; +}; diff --git a/Documentation/devicetree/bindings/power/ltc2941.txt b/Documentation/devicetree/bindings/power/supply/ltc2941.txt index ea42ae12d924..a9d7aa60558b 100644 --- a/Documentation/devicetree/bindings/power/ltc2941.txt +++ b/Documentation/devicetree/bindings/power/supply/ltc2941.txt @@ -6,8 +6,8 @@ temperature monitoring, and uses a slightly different conversion formula for the charge counter. Required properties: -- compatible: Should contain "ltc2941" or "ltc2943" which also indicates the - type of I2C chip attached. +- compatible: Should contain "lltc,ltc2941" or "lltc,ltc2943" which also + indicates the type of I2C chip attached. - reg: The 7-bit I2C address. - lltc,resistor-sense: The sense resistor value in milli-ohms. Can be a 32-bit negative value when the battery has been connected to the wrong end of the @@ -20,7 +20,7 @@ Required properties: Example from the Topic Miami Florida board: fuelgauge: ltc2943@64 { - compatible = "ltc2943"; + compatible = "lltc,ltc2943"; reg = <0x64>; lltc,resistor-sense = <15>; lltc,prescaler-exponent = <5>; /* 2^(2*5) = 1024 */ diff --git a/Documentation/devicetree/bindings/power/supply/ltc3651-charger.txt b/Documentation/devicetree/bindings/power/supply/ltc3651-charger.txt new file mode 100644 index 000000000000..71f2840e8209 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/ltc3651-charger.txt @@ -0,0 +1,27 @@ +ltc3651-charger + +Required properties: + - compatible: "lltc,ltc3651-charger" + - lltc,acpr-gpios: Connect to ACPR output. See remark below. + +Optional properties: + - lltc,fault-gpios: Connect to FAULT output. See remark below. + - lltc,chrg-gpios: Connect to CHRG output. See remark below. + +The ltc3651 outputs are open-drain type and active low. The driver assumes the +GPIO reports "active" when the output is asserted, so if the pins have been +connected directly, the GPIO flags should be set to active low also. + +The driver will attempt to aquire interrupts for all GPIOs to detect changes in +line state. If the system is not capabale of providing interrupts, the driver +cannot report changes and userspace will need to periodically read the sysfs +attributes to detect changes. + +Example: + + charger: battery-charger { + compatible = "lltc,ltc3651-charger"; + lltc,acpr-gpios = <&gpio0 68 GPIO_ACTIVE_LOW>; + lltc,fault-gpios = <&gpio0 64 GPIO_ACTIVE_LOW>; + lltc,chrg-gpios = <&gpio0 63 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/max17042_battery.txt b/Documentation/devicetree/bindings/power/supply/max17042_battery.txt new file mode 100644 index 000000000000..3f3894aaeebc --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/max17042_battery.txt @@ -0,0 +1,31 @@ +max17042_battery +~~~~~~~~~~~~~~~~ + +Required properties : + - compatible : "maxim,max17042" + +Optional properties : + - maxim,rsns-microohm : Resistance of rsns resistor in micro Ohms + (datasheet-recommended value is 10000). + Defining this property enables current-sense functionality. + +Optional threshold properties : + If skipped the condition won't be reported. + - maxim,cold-temp : Temperature threshold to report battery + as cold (in tenths of degree Celsius). + - maxim,over-heat-temp : Temperature threshold to report battery + as over heated (in tenths of degree Celsius). + - maxim,dead-volt : Voltage threshold to report battery + as dead (in mV). + - maxim,over-volt : Voltage threshold to report battery + as over voltage (in mV). + +Example: + + battery-charger@36 { + compatible = "maxim,max17042"; + reg = <0x36>; + maxim,rsns-microohm = <10000>; + maxim,over-heat-temp = <600>; + maxim,over-volt = <4300>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/max8903-charger.txt b/Documentation/devicetree/bindings/power/supply/max8903-charger.txt new file mode 100644 index 000000000000..f0f4e12b076e --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/max8903-charger.txt @@ -0,0 +1,25 @@ +Maxim Semiconductor MAX8903 Battery Charger bindings + +Required properties: +- compatible: "maxim,max8903" for MAX8903 Battery Charger +- dok-gpios: Valid DC power has been detected (active low, input), optional if uok-gpios is provided +- uok-gpios: Valid USB power has been detected (active low, input), optional if dok-gpios is provided + +Optional properties: +- cen-gpios: Charge enable pin (active low, output) +- chg-gpios: Charger status pin (active low, input) +- flt-gpios: Fault pin (active low, output) +- dcm-gpios: Current limit mode setting (DC=1 or USB=0, output) +- usus-gpios: USB suspend pin (active high, output) + + +Example: + + max8903-charger { + compatible = "maxim,max8903"; + dok-gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; + flt-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>; + chg-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; + cen-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/power/supply/max8925_battery.txt b/Documentation/devicetree/bindings/power/supply/max8925_battery.txt new file mode 100644 index 000000000000..d7e3e0c0f71d --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/max8925_battery.txt @@ -0,0 +1,18 @@ +max8925-battery bindings +~~~~~~~~~~~~~~~~ + +Optional properties : + - batt-detect: whether support battery detect + - topoff-threshold: set charging current in topoff mode + - fast-charge: set charging current in fast mode + - no-temp-support: whether support temperature protection detect + - no-insert-detect: whether support insert detect + +Example: + charger { + batt-detect = <0>; + topoff-threshold = <1>; + fast-charge = <7>; + no-temp-support = <0>; + no-insert-detect = <0>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/maxim,max14656.txt b/Documentation/devicetree/bindings/power/supply/maxim,max14656.txt new file mode 100644 index 000000000000..e03e85ae6572 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/maxim,max14656.txt @@ -0,0 +1,25 @@ +Maxim MAX14656 / AL32 USB Charger Detector + +Required properties : +- compatible : "maxim,max14656"; +- reg: i2c slave address +- interrupt-parent: the phandle for the interrupt controller +- interrupts: interrupt line + +Example: + +&i2c2 { + clock-frequency = <50000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + max14656@35 { + compatible = "maxim,max14656"; + reg = <0x35>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_charger_detect>; + interrupt-parent = <&gpio6>; + interrupts = <26 IRQ_TYPE_LEVEL_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/power/supply/olpc_battery.txt b/Documentation/devicetree/bindings/power/supply/olpc_battery.txt new file mode 100644 index 000000000000..c8901b3992d9 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/olpc_battery.txt @@ -0,0 +1,5 @@ +OLPC battery +~~~~~~~~~~~~ + +Required properties: + - compatible : "olpc,xo1-battery" diff --git a/Documentation/devicetree/bindings/power/supply/power_supply.txt b/Documentation/devicetree/bindings/power/supply/power_supply.txt new file mode 100644 index 000000000000..8391bfa0edac --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/power_supply.txt @@ -0,0 +1,23 @@ +Power Supply Core Support + +Optional Properties: + - power-supplies : This property is added to a supply in order to list the + devices which supply it power, referenced by their phandles. + +Example: + + usb-charger: power@e { + compatible = "some,usb-charger"; + ... + }; + + ac-charger: power@c { + compatible = "some,ac-charger"; + ... + }; + + battery@b { + compatible = "some,battery"; + ... + power-supplies = <&usb-charger>, <&ac-charger>; + }; diff --git a/Documentation/devicetree/bindings/power/qcom,coincell-charger.txt b/Documentation/devicetree/bindings/power/supply/qcom,coincell-charger.txt index 0e6d8754e7ec..747899223262 100644 --- a/Documentation/devicetree/bindings/power/qcom,coincell-charger.txt +++ b/Documentation/devicetree/bindings/power/supply/qcom,coincell-charger.txt @@ -29,7 +29,7 @@ IC (PMIC) - qcom,charger-disable: Usage: optional Value type: <boolean> - Definition: definining this property disables charging + Definition: defining this property disables charging This charger is a sub-node of one of the 8941 PMIC blocks, and is specified as a child node in DTS of that node. See ../mfd/qcom,spmi-pmic.txt and diff --git a/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt b/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt new file mode 100644 index 000000000000..06f8a5ddb68e --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt @@ -0,0 +1,150 @@ +Qualcomm Switch-Mode Battery Charger and Boost + +PROPERTIES +- compatible: + Usage: required + Value type: <stringlist> + Description: Must be one of: + - "qcom,pm8941-charger" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Description: Base address of registers for SMBB block + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Description: The format of the specifier is defined by the binding document + describing the node's interrupt parent. Must contain one + specifier for each of the following interrupts, in order: + - charge done + - charge fast mode + - charge trickle mode + - battery temperature ok + - battery present + - charger disconnected + - USB-in valid + - DC-in valid + +- interrupt-names: + Usage: required + Value type: <stringlist> + Description: Must contain the following list, strictly ordered: + "chg-done", + "chg-fast", + "chg-trkl", + "bat-temp-ok", + "bat-present", + "chg-gone", + "usb-valid", + "dc-valid" + +- qcom,fast-charge-current-limit: + Usage: optional (default: 1A, or pre-configured value) + Value type: <u32>; uA; range [100mA : 3A] + Description: Maximum charge current; May be clamped to safety limits. + +- qcom,fast-charge-low-threshold-voltage: + Usage: optional (default: 3.2V, or pre-configured value) + Value type: <u32>; uV; range [2.1V : 3.6V] + Description: Battery voltage limit above which fast charging may operate; + Below this value linear or switch-mode auto-trickle-charging + will operate. + +- qcom,fast-charge-high-threshold-voltage: + Usage: optional (default: 4.2V, or pre-configured value) + Value type: <u32>; uV; range [3.24V : 5V] + Description: Battery voltage limit below which fast charging may operate; + The fast charger will attempt to charge the battery to this + voltage. May be clamped to safety limits. + +- qcom,fast-charge-safe-voltage: + Usage: optional (default: 4.2V, or pre-configured value) + Value type: <u32>; uV; range [3.24V : 5V] + Description: Maximum safe battery voltage; May be pre-set by bootloader, in + which case, setting this will harmlessly fail. The property + 'fast-charge-high-watermark' will be clamped by this value. + +- qcom,fast-charge-safe-current: + Usage: optional (default: 1A, or pre-configured value) + Value type: <u32>; uA; range [100mA : 3A] + Description: Maximum safe battery charge current; May pre-set by bootloader, + in which case, setting this will harmlessly fail. The property + 'qcom,fast-charge-current-limit' will be clamped by this value. + +- qcom,auto-recharge-threshold-voltage: + Usage: optional (default: 4.1V, or pre-configured value) + Value type: <u32>; uV; range [3.24V : 5V] + Description: Battery voltage limit below which auto-recharge functionality + will restart charging after end-of-charge; The high cutoff + limit for auto-recharge is 5% above this value. + +- qcom,minimum-input-voltage: + Usage: optional (default: 4.3V, or pre-configured value) + Value type: <u32>; uV; range [4.2V : 9.6V] + Description: Input voltage level above which charging may operate + +- qcom,dc-current-limit: + Usage: optional (default: 100mA, or pre-configured value) + Value type: <u32>; uA; range [100mA : 2.5A] + Description: Default DC charge current limit + +- qcom,disable-dc: + Usage: optional (default: false) + Value type: boolean: <u32> or <empty> + Description: Disable DC charger + +- qcom,jeita-extended-temp-range: + Usage: optional (default: false) + Value type: boolean: <u32> or <empty> + Description: Enable JEITA extended temperature range; This does *not* + adjust the maximum charge voltage or current in the extended + temperature range. It only allows charging when the battery + is in the extended temperature range. Voltage/current + regulation must be done externally to fully comply with + the JEITA safety guidelines if this flag is set. + +- usb_otg_in-supply: + Usage: optional + Value type: <phandle> + Description: Reference to the regulator supplying power to the USB_OTG_IN + pin. + +child nodes: +- otg-vbus: + Usage: optional + Description: This node defines a regulator used to control the direction + of VBUS voltage - specifically: whether to supply voltage + to VBUS for host mode operation of the OTG port, or allow + input voltage from external VBUS for charging. In the + hardware, the supply for this regulator comes from + usb_otg_in-supply. + +EXAMPLE +charger@1000 { + compatible = "qcom,pm8941-charger"; + reg = <0x1000 0x700>; + interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>; + interrupt-names = "chg-done", + "chg-fast", + "chg-trkl", + "bat-temp-ok", + "bat-present", + "chg-gone", + "usb-valid", + "dc-valid"; + + qcom,fast-charge-current-limit = <1000000>; + qcom,dc-charge-current-limit = <1000000>; + usb_otg_in-supply = <&pm8941_5vs1>; + + otg-vbus {}; +}; diff --git a/Documentation/devicetree/bindings/power/rt9455_charger.txt b/Documentation/devicetree/bindings/power/supply/rt9455_charger.txt index 5d9ad5cf2c5a..5d9ad5cf2c5a 100644 --- a/Documentation/devicetree/bindings/power/rt9455_charger.txt +++ b/Documentation/devicetree/bindings/power/supply/rt9455_charger.txt diff --git a/Documentation/devicetree/bindings/power/rx51-battery.txt b/Documentation/devicetree/bindings/power/supply/rx51-battery.txt index 90438453db58..90438453db58 100644 --- a/Documentation/devicetree/bindings/power/rx51-battery.txt +++ b/Documentation/devicetree/bindings/power/supply/rx51-battery.txt diff --git a/Documentation/devicetree/bindings/power/supply/sbs_sbs-battery.txt b/Documentation/devicetree/bindings/power/supply/sbs_sbs-battery.txt new file mode 100644 index 000000000000..c40e8926facf --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/sbs_sbs-battery.txt @@ -0,0 +1,23 @@ +SBS sbs-battery +~~~~~~~~~~ + +Required properties : + - compatible : "sbs,sbs-battery" + +Optional properties : + - sbs,i2c-retry-count : The number of times to retry i2c transactions on i2c + IO failure. + - sbs,poll-retry-count : The number of times to try looking for new status + after an external change notification. + - sbs,battery-detect-gpios : The gpio which signals battery detection and + a flag specifying its polarity. + +Example: + + bq20z75@b { + compatible = "sbs,sbs-battery"; + reg = < 0xb >; + sbs,i2c-retry-count = <2>; + sbs,poll-retry-count = <10>; + sbs,battery-detect-gpios = <&gpio-controller 122 1>; + } diff --git a/Documentation/devicetree/bindings/power/supply/sbs_sbs-charger.txt b/Documentation/devicetree/bindings/power/supply/sbs_sbs-charger.txt new file mode 100644 index 000000000000..a3719623a94f --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/sbs_sbs-charger.txt @@ -0,0 +1,23 @@ +SBS sbs-charger +~~~~~~~~~~ + +Required properties: + - compatible: "<vendor>,<part-number>", "sbs,sbs-charger" as fallback. The part + number compatible string might be used in order to take care of vendor + specific registers. + +Optional properties: +- interrupt-parent: Should be the phandle for the interrupt controller. Use in + conjunction with "interrupts". +- interrupts: Interrupt mapping for GPIO IRQ. Use in conjunction with + "interrupt-parent". If an interrupt is not provided the driver will switch + automatically to polling. + +Example: + + ltc4100@9 { + compatible = "lltc,ltc4100", "sbs,sbs-charger"; + reg = <0x9>; + interrupt-parent = <&gpio6>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt b/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt new file mode 100644 index 000000000000..de45e1a2a4d9 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt @@ -0,0 +1,39 @@ +TI BQ24735 Charge Controller +~~~~~~~~~~ + +Required properties : + - compatible : "ti,bq24735" + +Optional properties : + - interrupts : Specify the interrupt to be used to trigger when the AC + adapter is either plugged in or removed. + - ti,ac-detect-gpios : This GPIO is optionally used to read the AC adapter + status. This is a Host GPIO that is configured as an input and connected + to the ACOK pin on the bq24735. Note: for backwards compatibility reasons, + the GPIO must be active on AC adapter absence despite ACOK being active + (high) on AC adapter presence. + - ti,charge-current : Used to control and set the charging current. This value + must be between 128mA and 8.128A with a 64mA step resolution. The POR value + is 0x0000h. This number is in mA (e.g. 8192), see spec for more information + about the ChargeCurrent (0x14h) register. + - ti,charge-voltage : Used to control and set the charging voltage. This value + must be between 1.024V and 19.2V with a 16mV step resolution. The POR value + is 0x0000h. This number is in mV (e.g. 19200), see spec for more information + about the ChargeVoltage (0x15h) register. + - ti,input-current : Used to control and set the charger input current. This + value must be between 128mA and 8.064A with a 128mA step resolution. The + POR value is 0x1000h. This number is in mA (e.g. 8064), see the spec for + more information about the InputCurrent (0x3fh) register. + - ti,external-control : Indicates that the charger is configured externally + and that the host should not attempt to enable/disable charging or set the + charge voltage/current. + - poll-interval : In case 'interrupts' is not specified, poll AC adapter + presence with this interval (milliseconds). + +Example: + + bq24735@9 { + compatible = "ti,bq24735"; + reg = <0x9>; + ti,ac-detect-gpios = <&gpio 72 0x1>; + } diff --git a/Documentation/devicetree/bindings/power/supply/tps65090.txt b/Documentation/devicetree/bindings/power/supply/tps65090.txt new file mode 100644 index 000000000000..8e5e0d3910df --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/tps65090.txt @@ -0,0 +1,17 @@ +TPS65090 Frontend PMU with Switchmode Charger + +Required Properties: +-compatible: "ti,tps65090-charger" + +Optional Properties: +-ti,enable-low-current-chrg: Enables charging when a low current is detected + while the default logic is to stop charging. + +This node is a subnode of the tps65090 PMIC. + +Example: + + tps65090-charger { + compatible = "ti,tps65090-charger"; + ti,enable-low-current-chrg; + }; diff --git a/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt b/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt new file mode 100644 index 000000000000..a11072c5a866 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt @@ -0,0 +1,17 @@ +TPS65217 Charger + +Required Properties: +-compatible: "ti,tps65217-charger" +-interrupts: TPS65217 interrupt numbers for the AC and USB charger input change. + Should be <0> for the USB charger and <1> for the AC adapter. +-interrupt-names: Should be "USB" and "AC" + +This node is a subnode of the tps65217 PMIC. + +Example: + + tps65217-charger { + compatible = "ti,tps65217-charger"; + interrupts = <0>, <1>; + interrupt-names = "USB", "AC"; + }; diff --git a/Documentation/devicetree/bindings/power/twl-charger.txt b/Documentation/devicetree/bindings/power/supply/twl-charger.txt index 3b4ea1b73b38..3b4ea1b73b38 100644 --- a/Documentation/devicetree/bindings/power/twl-charger.txt +++ b/Documentation/devicetree/bindings/power/supply/twl-charger.txt |