Age | Commit message (Collapse) | Author |
|
|
|
A hardware/firmware error may happen at any point in time. In
particular, it might happen while mac80211 is in the middle of
a flow. We observed the following situation:
* mac80211 is in authentication flow, in ieee80211_prep_connection()
* iwlwifi firmware crashes, but no error can be reported at this
precise point (mostly because the driver method is void, but even
if it wasn't we'd just shift to a race condition)
* mac80211 continues the flow, trying to add the AP station
* iwlwifi has already set its internal restart flag, and so thinks
that adding the station is part of the restart and already set up,
so it uses the information that's supposed to already be in the
struct
This can happen with any flow in mac80211 and with any information
we try to preserve across hardware restarts.
To fix this, only set a new HW_RESTART_REQUESTED flag and translate
that to IN_HW_RESTART once mac80211 actually starts the restart by
calling our start() method. As a consequence, any mac80211 flow in
progress at the time of the restart will properly finish (certainly
with errors), before the restart is attempted.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195299.
Reported-by: djagoo <dev@djagoo.io>
Reported-by: Łukasz Siudut <lsiudut@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When IBSS was implemented for DQA, we missid a few places where it
should be handled in the same way as AP.
Fixes: ee48b72211f8 ("iwlwifi: mvm: support ibss in dqa mode")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
iwl_trace_data is somewhat confusing. It returns a bool
that tells if the payload of the skb should be added to
the tx_data event. If it returns false, then the payload
of the skb is added to the tx event.
The purpose is to be able to start tracing with
-e iwlwifi
and record non-data packets only which saves bandwidth.
Since EAPOLs are important, seldom and not real data
packet (despite being WiFi data packets), they are
included in tx event and thus iwl_trace_data returns false
on those. This last part was buggy, and because of that,
all the data packets were included in the tx event.
Fix that.
Fixes: 0c4cb7314d15 ("iwlwifi: tracing: decouple from mac80211")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We don't set the error code here so we end up returning ERR_PTR(0) which
is NULL. The caller doesn't expect that so it results in a NULL
dereference.
Fixes: 2e5d4a8f61dc ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Sometimes, we can have an firmware crash while trying to
recover from a previous firmware problem.
When that happens, lots of things can go wrong. For example
the stations don't get added properly to mvm->fw_id_to_mac_id.
Mac80211 tries to stop A-MPDU upon reconfig but in case of
a firmware crash we will bail out fairly early and in the
end, we won't delete the A-MPDU Rx timeout.
When that timer expired after a double firmware crash,
we end up dereferencing mvm->fw_id_to_mac_id[sta_id]
which is NULL.
Fixes: 10b2b2019d81 ("iwlwifi: mvm: add infrastructure for tracking BA session in driver")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Before TVQM, all TX queues were allocated straight at init.
With TVQM, queues are allocated on demand and hence we need
to check if a queue exists before dereferencing it.
Fixes: 66128fa08806 ("iwlwifi: move to TVQM mode")
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
iwlagn_check_ratid_empty takes the tid as a parameter, but
it doesn't check that it is not IWL_TID_NON_QOS.
Since IWL_TID_NON_QOS = 8 and iwl_priv::tid_data is an array
with 8 entries, accessing iwl_priv::tid_data[IWL_TID_NON_QOS]
is a bad idea.
This happened in iwlagn_rx_reply_tx. Since
iwlagn_check_ratid_empty is relevant only to check whether
we can open A-MPDU, this flow is irrelevant if tid is
IWL_TID_NON_QOS. Call iwlagn_check_ratid_empty only inside
the
if (tid != IWL_TID_NON_QOS)
a few lines earlier in the function.
Cc: <stable@vger.kernel.org>
Reported-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Tested-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This reverts commit f95d95a7cd5514549dcf6ba754f0ee834cce3e1f.
With commit f95d95a7cd55 ("rtlwifi: btcoex: rtl8723be: fix ant_sel not
work"), the kernel has a NULL pointer dereference oops. This content and
the proper fix will be included in a later patch.
Fixes: f95d95a7cd55 ("rtlwifi: btcoex: rtl8723be: fix ant_sel not work")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Recent change in brcmf_sdio_txpkt_hdalign() changed the
behavior and now always returns 0. This resulted in a
regression which basically renders the device useless.
Fixes: 270a6c1f65fe ("brcmfmac: rework headroom check in .start_xmit()")
Reported-by: S. Gilles <sgilles@math.umd.edu>
Tested-by: S. Gilles <sgilles@math.umd.edu>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
|
|
Pull networking fixes from David Miller:
1) BPF verifier signed/unsigned value tracking fix, from Daniel
Borkmann, Edward Cree, and Josef Bacik.
2) Fix memory allocation length when setting up calls to
->ndo_set_mac_address, from Cong Wang.
3) Add a new cxgb4 device ID, from Ganesh Goudar.
4) Fix FIB refcount handling, we have to set it's initial value before
the configure callback (which can bump it). From David Ahern.
5) Fix double-free in qcom/emac driver, from Timur Tabi.
6) A bunch of gcc-7 string format overflow warning fixes from Arnd
Bergmann.
7) Fix link level headroom tests in ip_do_fragment(), from Vasily
Averin.
8) Fix chunk walking in SCTP when iterating over error and parameter
headers. From Alexander Potapenko.
9) TCP BBR congestion control fixes from Neal Cardwell.
10) Fix SKB fragment handling in bcmgenet driver, from Doug Berger.
11) BPF_CGROUP_RUN_PROG_SOCK_OPS needs to check for null __sk, from Cong
Wang.
12) xmit_recursion in ppp driver needs to be per-device not per-cpu,
from Gao Feng.
13) Cannot release skb->dst in UDP if IP options processing needs it.
From Paolo Abeni.
14) Some netdev ioctl ifr_name[] NULL termination fixes. From Alexander
Levin and myself.
15) Revert some rtnetlink notification changes that are causing
regressions, from David Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (83 commits)
net: bonding: Fix transmit load balancing in balance-alb mode
rds: Make sure updates to cp_send_gen can be observed
net: ethernet: ti: cpsw: Push the request_irq function to the end of probe
ipv4: initialize fib_trie prior to register_netdev_notifier call.
rtnetlink: allocate more memory for dev_set_mac_address()
net: dsa: b53: Add missing ARL entries for BCM53125
bpf: more tests for mixed signed and unsigned bounds checks
bpf: add test for mixed signed and unsigned bounds checks
bpf: fix up test cases with mixed signed/unsigned bounds
bpf: allow to specify log level and reduce it for test_verifier
bpf: fix mixed signed/unsigned derived min/max value bounds
ipv6: avoid overflow of offset in ip6_find_1stfragopt
net: tehuti: don't process data if it has not been copied from userspace
Revert "rtnetlink: Do not generate notifications for CHANGEADDR event"
net: dsa: mv88e6xxx: Enable CMODE config support for 6390X
dt-binding: ptp: Add SoC compatibility strings for dte ptp clock
NET: dwmac: Make dwmac reset unconditional
net: Zero terminate ifr_name in dev_ifname().
wireless: wext: terminate ifr name coming from userspace
netfilter: fix netfilter_net_init() return
...
|
|
balance-alb mode used to have transmit dynamic load balancing feature
enabled by default. However, transmit dynamic load balancing no longer
works in balance-alb after commit 8b426dc54cf4 ("bonding: remove
hardcoded value").
Both balance-tlb and balance-alb use the function bond_do_alb_xmit() to
send packets. This function uses the parameter tlb_dynamic_lb.
tlb_dynamic_lb used to have the default value of 1 for balance-alb, but
now the value is set to 0 except in balance-tlb.
Re-enable transmit dyanmic load balancing by initializing tlb_dynamic_lb
for balance-alb similar to balance-tlb.
Fixes: 8b426dc54cf4 ("bonding: remove hardcoded value")
Signed-off-by: Kosuke Tatsukawa <tatsu@ab.jp.nec.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
print the versions of vpd and serial configuration file,
flashed to adapter, and cleanup the relevant code.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Push the request_irq function to the end of probe so as
to ensure all the required fields are populated in the event
of an ISR getting executed right after requesting the irq.
Currently while loading the crash kernel a crash was seen as
soon as devm_request_threaded_irq was called. This was due to
n->poll being NULL which is called as part of net_rx_action
function.
Suggested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The BCM53125 entry was missing an arl_entries member which would
basically prevent the ARL search from terminating properly. This switch
has 4 ARL entries, so add that.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The array data is only populated with valid information from userspace
if cmd != SIOCDEVPRIVATE, other cases the array contains garbage on
the stack. The subsequent switch statement acts on a subcommand in
data[0] which could be any garbage value if cmd is SIOCDEVPRIVATE which
seems incorrect to me. Instead, just return EOPNOTSUPP for the case
where cmd == SIOCDEVPRIVATE to avoid this issue.
As a side note, I suspect that the original intention of the code
was for this ioctl to work just for cmd == SIOCDEVPRIVATE (and the
current logic is reversed). However, I don't wont to change the current
semantics in case any userspace code relies on this existing behaviour.
Detected by CoverityScan, CID#139647 ("Uninitialized scalar variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit f39908d3b1c45 ('net: dsa: mv88e6xxx: Set the CMODE for mv88e6390
ports 9 & 10') added support for setting the CMODE for the 6390X family,
but only enabled it for 9290 and 6390 - and left out 6390X.
Fix support for setting the CMODE on 6390X also by assigning
mv88e6390x_port_set_cmode() to the .port_set_cmode function pointer in
mv88e6390x_ops too.
Fixes: f39908d3b1c4 ("net: dsa: mv88e6xxx: Set the CMODE for mv88e6390 ports 9 & 10")
Signed-off-by: Martin Hundebøll <mnhu@prevas.dk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rndis functions are used when changing device state.
Therefore the references from network device to internal state
are protected by RTNL mutex.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Keep back pointer in the per-channel data structure to
avoid any possible RCU related issues when napi poll is
called but netvsc_device is in RCU limbo.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netvsc_device structure should be accessed by rcu_dereference
in the send path. Change arguments to netvsc_send() to make
this easier to do correctly.
Remove no longer needed hv_device_to_netvsc_device.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rndis_filter_device_add function is called both in
probe context and RTNL context,and creates the netvsc_device
inner structure. It is easier to get the RTNL lock annotation
correct if it returns the object directly, rather than implicitly
by updating network device private data.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use device detach/attach to ensure that no packets are handed
to device during state changes. Call rndis_filter_open/close
directly as part of later VF related changes.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes the error unwind logic for incorrect number of queues.
If netif_set_real_num_XX_queues failed then rndis_filter_device_add
would have been called twice. Since input arguments are already
ranged checked this is a hypothetical only problem, not possible
in actual code.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a couple places RTNL is held, and the netvsc_device pointer
is acquired without annotation.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If two MTU changes are in less than update interval (2 seconds),
then the netvsc network device may get stuck with no carrier.
The netvsc driver debounces link status events which is fine
for unsolicited updates, but blocks getting the update after
down/up from MTU reinitialization.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to cast away return value of dev_close.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove unnecessary static on local variables cpu_id_modulus and cpu_id.
Such variables are initialized before being used, on every execution
path throughout the function. The static has no benefit and, removing
it reduces the object file size.
This issue was detected using Coccinelle and the following semantic patch:
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
In the following log you can see a significant difference in the object
file size. Also, there is a significant difference in the bss segment.
This log is the output of the size command, before and after the code
change:
before:
text data bss dec hex filename
78689 15272 27808 121769 1dba9 drivers/net/ethernet/cavium/liquidio/lio_main.o
after:
text data bss dec hex filename
78667 15128 27680 121475 1da83 drivers/net/ethernet/cavium/liquidio/lio_main.o
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove unnecessary static on local variables cpu_id_modulus and cpu_id.
Such variables are initialized before being used, on every execution
path throughout the function. The static has no benefit and, removing
it reduces the object file size.
This issue was detected using Coccinelle and the following semantic patch:
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
In the following log you can see a significant difference in the object
file size. Also, there is a significant difference in the bss segment.
This log is the output of the size command, before and after the code
change:
before:
text data bss dec hex filename
55656 10680 576 66912 10560 drivers/net/ethernet/cavium/liquidio/lio_vf_main.o
after:
text data bss dec hex filename
55796 10536 448 66780 104dc drivers/net/ethernet/cavium/liquidio/lio_vf_main.o
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove useless local variable _condition_ and the code related.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove unnecessary static on local variable fw_dump_ops.
Such variable is initialized before being used, on every
execution path throughout the function. The static has no
benefit and, removing it reduces the object file size.
This issue was detected using Coccinelle and the following semantic patch:
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
In the following log you can see a difference in the object file size.
This log is the output of the size command, before and after the code
change:
before:
text data bss dec hex filename
19032 2136 64 21232 52f0 drivers/net/ethernet/qlogic/qlcnic/qlcnic_minidump.o
after:
text data bss dec hex filename
19020 2048 0 21068 524c drivers/net/ethernet/qlogic/qlcnic/qlcnic_minidump.o
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove useless local variable multiport_cnt and the code related.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove useless local variables last_read_point and last_txw_point and
the code related.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove unnecessary static on local function pointer _writer_.
Such pointer is initialized before being used, on every
execution path throughout the function. The static has no
benefit and, removing it reduces the object file size.
This issue was detected using Coccinelle and the following semantic patch:
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
In the following log you can see a significant difference in the object
file size. This log is the output of the size command, before and after
the code change:
before:
text data bss dec hex filename
113797 19152 1216 134165 20c15 drivers/net/wireless/cisco/airo.o
after:
text data bss dec hex filename
113881 19096 1152 134129 20bf1 drivers/net/wireless/cisco/airo.o
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This also adds support for non-QSFP modules attached to QSFP.
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unconditional reset dwmac before HW init if reset controller is present.
In existing implementation we reset dwmac only after second module
probing:
(module load -> unload -> load again [reset happens])
Now we reset dwmac at every module load:
(module load [reset happens] -> unload -> load again [reset happens])
Also some reset controllers have only reset callback instead of
assert + deassert callbacks pair, so handle this case.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For defensive programming, zero the allocated block 'oct->droq[0]' in
octeon_setup_output_queues() and 'oct->instr_queue[0]' in
octeon_setup_instr_queues().
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't dereference a NULL ptr in octeon_droq_destroy_ring_buffers().
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix GPF in octeon_init_droq(); zero the allocated block 'recv_buf_list'.
This prevents a GPF trying to access an invalid 'recv_buf_list[i]' entry
in octeon_droq_destroy_ring_buffers() if init didn't alloc all entries.
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added support for new firmware statistic 'tx_err_pki'.
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
28720 985 12 29717 7415 net/.../cxgb3/cxgb3_main.o
File size After adding 'const':
text data bss dec hex filename
28848 857 12 29717 7415 net/.../cxgb3/cxgb3_main.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/netdevice.h> work
with const attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
4512 1472 0 5984 1760 drivers/net/bonding/bond_sysfs.o
File size After adding 'const':
text data bss dec hex filename
4576 1408 0 5984 1760 drivers/net/bonding/bond_sysfs.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/netdevice.h> work
with const attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
3409 948 28 4385 1121 drivers/net/arcnet/com20020-pci.o
File size After adding 'const':
text data bss dec hex filename
3473 884 28 4385 1121 drivers/net/arcnet/com20020-pci.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/netdevice.h> work
with const attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
11800 368 0 12168 2f88 drivers/net/can/janz-ican3.o
File size After adding 'const':
text data bss dec hex filename
11864 304 0 12168 2f88 drivers/net/can/janz-ican3.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/netdevice.h> work
with const attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
6164 304 0 6468 1944 drivers/net/can/at91_can.o
File size After adding 'const':
text data bss dec hex filename
6228 240 0 6468 1944 drivers/net/can/at91_can.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|