| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 bug fixes from Martin Schwidefsky:
- Fix overwrite of the initial ramdisk due to misuse of IS_ENABLED
- Fix integer overflow in the dasd driver resulting in incorrect number
of blocks for large devices
- Fix a lockdep false positive in the 3270 driver
- Fix a deadlock in the zcrypt driver
- Fix incorrect debug feature entries in the pkey api
- Fix inline assembly constraints fallout with CONFIG_KASAN=y
* tag 's390-5.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: correct some inline assembly constraints
s390/pkey: add one more argument space for debug feature entry
s390/zcrypt: fix possible deadlock situation on ap queue remove
s390/3270: fix lockdep false positive on view->lock
s390/dasd: Fix capacity calculation for large volumes
s390/mem_detect: Use IS_ENABLED(CONFIG_BLK_DEV_INITRD)
|
|
The debug feature entries have been used with up to 5 arguents
(including the pointer to the format string) but there was only
space reserved for 4 arguemnts. So now the registration does
reserve space for 5 times a long value.
This fixes a sometime appearing weired value as the last
value of an debug feature entry like this:
... pkey_sec2protkey zcrypt_send_cprb (cardnr=10 domain=12)
failed with errno -2143346254
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reported-by: Christian Rund <Christian.Rund@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
With commit 01396a374c3d ("s390/zcrypt: revisit ap device remove
procedure") the ap queue remove is now a two stage process. However,
a del_timer_sync() call may trigger the timer function which may
try to lock the very same spinlock as is held by the function
just initiating the del_timer_sync() call. This could end up in
a deadlock situation. Very unlikely but possible as you need to
remove an ap queue at the exact sime time when a timeout of a
request occurs.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reported-by: Pierre Morel <pmorel@linux.ibm.com>
Fixes: commit 01396a374c3d ("s390/zcrypt: revisit ap device remove procedure")
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The spinlock in the raw3270_view structure is used by con3270, tty3270
and fs3270 in different ways. For con3270 the lock can be acquired in
irq context, for tty3270 and fs3270 the highest context is bh.
Lockdep sees the view->lock as a single class and if the 3270 driver
is used for the console the following message is generated:
WARNING: inconsistent lock state
5.1.0-rc3-05157-g5c168033979d #12 Not tainted
--------------------------------
inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
swapper/0/1 [HC0[0]:SC1[1]:HE1:SE0] takes:
(____ptrval____) (&(&view->lock)->rlock){?.-.}, at: tty3270_update+0x7c/0x330
Introduce a lockdep subclass for the view lock to distinguish bh from
irq locks.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Thirteen fixes, seven of which are for IBM fibre channel and three
additional for fairly serious bugs in drivers (qla2xxx, mpt3sas,
aacraid).
Of the three core fixes, the most significant is probably the missed
run queue causing an indefinite hang. The others are fixing a
potential use after free on device close and silencing an incorrect
warning"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ibmvfc: Clean up transport events
scsi: ibmvfc: Byte swap status and error codes when logging
scsi: ibmvfc: Add failed PRLI to cmd_status lookup array
scsi: ibmvfc: Remove "failed" from logged errors
scsi: zfcp: reduce flood of fcrscn1 trace records on multi-element RSCN
scsi: zfcp: fix scsi_eh host reset with port_forced ERP for non-NPIV FCP devices
scsi: zfcp: fix rport unblock if deleted SCSI devices on Scsi_Host
scsi: sd: Quiesce warning if device does not report optimal I/O size
scsi: sd: Fix a race between closing an sd device and sd I/O
scsi: core: Run queue when state is set to running after being blocked
scsi: qla4xxx: fix a potential NULL pointer dereference
scsi: aacraid: Insure we don't access PCIe space during AER/EEH
scsi: mpt3sas: Fix kernel panic during expander reset
|
|
The DASD driver incorrectly limits the maximum number of blocks of ECKD
DASD volumes to 32 bit numbers. Volumes with a capacity greater than
2^32-1 blocks are incorrectly recognized as smaller volumes.
This results in the following volume capacity limits depending on the
formatted block size:
BLKSIZE MAX_GB MAX_CYL
512 2047 5843492
1024 4095 8676701
2048 8191 13634816
4096 16383 23860929
The same problem occurs when a volume with more than 17895697 cylinders
is accessed in raw-track-access mode.
Fix this problem by adding an explicit type cast when calculating the
maximum number of blocks.
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Improvements and bug fixes for 5.1-rc2:
- Fix early free of the channel program in vfio
- On AP device removal make sure that all messages are flushed with
the driver still attached that queued the message
- Limit brk randomization to 32MB to reduce the chance that the heap
of ld.so is placed after the main stack
- Add a rolling average for the steal time of a CPU, this will be
needed for KVM to decide when to do busy waiting
- Fix a warning in the CPU-MF code
- Add a notification handler for AP configuration change to react
faster to new AP devices"
* tag 's390-5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/cpumf: Fix warning from check_processor_id
zcrypt: handle AP Info notification from CHSC SEI command
vfio: ccw: only free cp on final interrupt
s390/vtime: steal time exponential moving average
s390/zcrypt: revisit ap device remove procedure
s390: limit brk randomization to 32MB
|
|
If an incoming ELS of type RSCN contains more than one element, zfcp
suboptimally causes repeated erp trigger NOP trace records for each
previously failed port. These could be ports that went away. It loops over
each RSCN element, and for each of those in an inner loop over all
zfcp_ports.
The trigger to recover failed ports should be just the reception of some
RSCN, no matter how many elements it has. So we can loop over failed ports
separately, and only then loop over each RSCN element to handle the
non-failed ports.
The call chain was:
zfcp_fc_incoming_rscn
for (i = 1; i < no_entries; i++)
_zfcp_fc_incoming_rscn
list_for_each_entry(port, &adapter->port_list, list)
if (masked port->d_id match) zfcp_fc_test_link
if (!port->d_id) zfcp_erp_port_reopen "fcrscn1" <===
In order the reduce the "flooding" of the REC trace area in such cases, we
factor out handling the failed ports to be outside of the entries loop:
zfcp_fc_incoming_rscn
if (no_entries > 1) <===
list_for_each_entry(port, &adapter->port_list, list) <===
if (!port->d_id) zfcp_erp_port_reopen "fcrscn1" <===
for (i = 1; i < no_entries; i++)
_zfcp_fc_incoming_rscn
list_for_each_entry(port, &adapter->port_list, list)
if (masked port->d_id match) zfcp_fc_test_link
Abbreviated example trace records before this code change:
Tag : fcrscn1
WWPN : 0x500507630310d327
ERP want : 0x02
ERP need : 0x02
Tag : fcrscn1
WWPN : 0x500507630310d327
ERP want : 0x02
ERP need : 0x00 NOP => superfluous trace record
The last trace entry repeats if there are more than 2 RSCN elements.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Suppose more than one non-NPIV FCP device is active on the same channel.
Send I/O to storage and have some of the pending I/O run into a SCSI
command timeout, e.g. due to bit errors on the fibre. Now the error
situation stops. However, we saw FCP requests continue to timeout in the
channel. The abort will be successful, but the subsequent TUR fails.
Scsi_eh starts. The LUN reset fails. The target reset fails. The host
reset only did an FCP device recovery. However, for non-NPIV FCP devices,
this does not close and reopen ports on the SAN-side if other non-NPIV FCP
device(s) share the same open ports.
In order to resolve the continuing FCP request timeouts, we need to
explicitly close and reopen ports on the SAN-side.
This was missing since the beginning of zfcp in v2.6.0 history commit
ea127f975424 ("[PATCH] s390 (7/7): zfcp host adapter.").
Note: The FSF requests for forced port reopen could run into FSF request
timeouts due to other reasons. This would trigger an internal FCP device
recovery. Pending forced port reopen recoveries would get dismissed. So
some ports might not get fully reopened during this host reset handler.
However, subsequent I/O would trigger the above described escalation and
eventually all ports would be forced reopen to resolve any continuing FCP
request timeouts due to earlier bit errors.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: <stable@vger.kernel.org> #3.0+
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
An already deleted SCSI device can exist on the Scsi_Host and remain there
because something still holds a reference. A new SCSI device with the same
H:C:T:L and FCP device, target port WWPN, and FCP LUN can be created. When
we try to unblock an rport, we still find the deleted SCSI device and
return early because the zfcp_scsi_dev of that SCSI device is not
ZFCP_STATUS_COMMON_UNBLOCKED. Hence we miss to unblock the rport, even if
the new proper SCSI device would be in good state.
Therefore, skip deleted SCSI devices when iterating the sdevs of the shost.
[cf. __scsi_device_lookup{_by_target}() or scsi_device_get()]
The following abbreviated trace sequence can indicate such problem:
Area : REC
Tag : ersfs_3
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x40000000 not ZFCP_STATUS_COMMON_UNBLOCKED
Ready count : n not incremented yet
Running count : 0x00000000
ERP want : 0x01
ERP need : 0xc1 ZFCP_ERP_ACTION_NONE
Area : REC
Tag : ersfs_3
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x41000000
Ready count : n+1
Running count : 0x00000000
ERP want : 0x01
ERP need : 0x01
...
Area : REC
Level : 4 only with increased trace level
Tag : ertru_l
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x40000000
Request ID : 0x0000000000000000
ERP status : 0x01800000
ERP step : 0x1000
ERP action : 0x01
ERP count : 0x00
NOT followed by a trace record with tag "scpaddy"
for WWPN 0x50050763031bd327.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: 6f2ce1c6af37 ("scsi: zfcp: fix rport unblock race with LUN recovery")
Cc: <stable@vger.kernel.org> #2.6.32+
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull networking fixes from David Miller:
"Fixes here and there, a couple new device IDs, as usual:
1) Fix BQL race in dpaa2-eth driver, from Ioana Ciornei.
2) Fix 64-bit division in iwlwifi, from Arnd Bergmann.
3) Fix documentation for some eBPF helpers, from Quentin Monnet.
4) Some UAPI bpf header sync with tools, also from Quentin Monnet.
5) Set descriptor ownership bit at the right time for jumbo frames in
stmmac driver, from Aaro Koskinen.
6) Set IFF_UP properly in tun driver, from Eric Dumazet.
7) Fix load/store doubleword instruction generation in powerpc eBPF
JIT, from Naveen N. Rao.
8) nla_nest_start() return value checks all over, from Kangjie Lu.
9) Fix asoc_id handling in SCTP after the SCTP_*_ASSOC changes this
merge window. From Marcelo Ricardo Leitner and Xin Long.
10) Fix memory corruption with large MTUs in stmmac, from Aaro
Koskinen.
11) Do not use ipv4 header for ipv6 flows in TCP and DCCP, from Eric
Dumazet.
12) Fix topology subscription cancellation in tipc, from Erik Hugne.
13) Memory leak in genetlink error path, from Yue Haibing.
14) Valid control actions properly in packet scheduler, from Davide
Caratti.
15) Even if we get EEXIST, we still need to rehash if a shrink was
delayed. From Herbert Xu.
16) Fix interrupt mask handling in interrupt handler of r8169, from
Heiner Kallweit.
17) Fix leak in ehea driver, from Wen Yang"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (168 commits)
dpaa2-eth: fix race condition with bql frame accounting
chelsio: use BUG() instead of BUG_ON(1)
net: devlink: skip info_get op call if it is not defined in dumpit
net: phy: bcm54xx: Encode link speed and activity into LEDs
tipc: change to check tipc_own_id to return in tipc_net_stop
net: usb: aqc111: Extend HWID table by QNAP device
net: sched: Kconfig: update reference link for PIE
net: dsa: qca8k: extend slave-bus implementations
net: dsa: qca8k: remove leftover phy accessors
dt-bindings: net: dsa: qca8k: support internal mdio-bus
dt-bindings: net: dsa: qca8k: fix example
net: phy: don't clear BMCR in genphy_soft_reset
bpf, libbpf: clarify bump in libbpf version info
bpf, libbpf: fix version info and add it to shared object
rxrpc: avoid clang -Wuninitialized warning
tipc: tipc clang warning
net: sched: fix cleanup NULL pointer exception in act_mirr
r8169: fix cable re-plugging issue
net: ethernet: ti: fix possible object reference leak
net: ibm: fix possible object reference leak
...
|
|
As part of the TX completion path, qeth_release_skbs() frees the completed
skbs with __skb_queue_purge(). This ends in kfree_skb(), reporting every
completed skb as dropped.
On the other hand when dropping an skb in .ndo_start_xmit, we end up
calling consume_skb()... where we should be using kfree_skb() so that
drop monitors get notified.
Switch the drop/consume logic around, and also don't accumulate dropped
packets in the tx_errors statistics.
Fixes: dc149e3764d8 ("s390/qeth: replace open-coded skb_queue_walk()")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ucast IP table is utilized by some of the L3-specific sysfs attributes
that qeth_l3_create_device_attributes() provides. So initialize the table
_before_ registering the attributes.
Fixes: ebccc7397e4a ("s390/qeth: add missing hash table initializations")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The HW trap and VNICC configuration is exposed via sysfs, and may have
already been modified when qeth_l?_probe_device() attempts to initialize
them. So (1) initialize the VNICC values a little earlier, and (2) don't
bother about the HW trap mode, it was already initialized before.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull KVM updates from Paolo Bonzini:
"ARM:
- some cleanups
- direct physical timer assignment
- cache sanitization for 32-bit guests
s390:
- interrupt cleanup
- introduction of the Guest Information Block
- preparation for processor subfunctions in cpu models
PPC:
- bug fixes and improvements, especially related to machine checks
and protection keys
x86:
- many, many cleanups, including removing a bunch of MMU code for
unnecessary optimizations
- AVIC fixes
Generic:
- memcg accounting"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (147 commits)
kvm: vmx: fix formatting of a comment
KVM: doc: Document the life cycle of a VM and its resources
MAINTAINERS: Add KVM selftests to existing KVM entry
Revert "KVM/MMU: Flush tlb directly in the kvm_zap_gfn_range()"
KVM: PPC: Book3S: Add count cache flush parameters to kvmppc_get_cpu_char()
KVM: PPC: Fix compilation when KVM is not enabled
KVM: Minor cleanups for kvm_main.c
KVM: s390: add debug logging for cpu model subfunctions
KVM: s390: implement subfunction processor calls
arm64: KVM: Fix architecturally invalid reset value for FPEXC32_EL2
KVM: arm/arm64: Remove unused timer variable
KVM: PPC: Book3S: Improve KVM reference counting
KVM: PPC: Book3S HV: Fix build failure without IOMMU support
Revert "KVM: Eliminate extra function calls in kvm_get_dirty_log_protect()"
x86: kvmguest: use TSC clocksource if invariant TSC is exposed
KVM: Never start grow vCPU halt_poll_ns from value below halt_poll_ns_grow_start
KVM: Expose the initial start value in grow_halt_poll_ns() as a module parameter
KVM: grow_halt_poll_ns() should never shrink vCPU halt_poll_ns
KVM: x86/mmu: Consolidate kvm_mmu_zap_all() and kvm_mmu_zap_mmio_sptes()
KVM: x86/mmu: WARN if zapping a MMIO spte results in zapping children
...
|
|
The current AP bus implementation periodically polls the AP configuration
to detect changes. When the AP configuration is dynamically changed via the
SE or an SCLP instruction, the changes will not be reflected to sysfs until
the next time the AP configuration is polled. The CHSC architecture
provides a Store Event Information (SEI) command to make notification of an
AP configuration change. This patch introduces a handler to process
notification from the CHSC SEI command by immediately kicking off an AP bus
scan-after-event.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Sebastian Ott <sebott@linux.ibm.com>
Reviewed-by: Harald Freudenberger <FREUDE@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
When we get an interrupt for a channel program, it is not
necessarily the final interrupt; for example, the issuing
guest may request an intermediate interrupt by specifying
the program-controlled-interrupt flag on a ccw.
We must not switch the state to idle if the interrupt is not
yet final; even more importantly, we must not free the translated
channel program if the interrupt is not yet final, or the host
can crash during cp rewind.
Fixes: e5f84dbaea59 ("vfio: ccw: return I/O results asynchronously")
Cc: stable@vger.kernel.org # v4.12+
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
|
|
Pull virtio updates from Michael Tsirkin:
"Several fixes, most notably fix for virtio on swiotlb systems"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost: silence an unused-variable warning
virtio: hint if callbacks surprisingly might sleep
virtio-ccw: wire up ->bus_name callback
s390/virtio: handle find on invalid queue gracefully
virtio-ccw: diag 500 may return a negative cookie
virtio_balloon: remove the unnecessary 0-initialization
virtio-balloon: improve update_balloon_size_func
virtio-blk: Consider virtio_max_dma_size() for maximum segment size
virtio: Introduce virtio_max_dma_size()
dma: Introduce dma_max_mapping_size()
swiotlb: Add is_swiotlb_active() function
swiotlb: Introduce swiotlb_max_mapping_size()
|
|
Return the bus id of the ccw proxy device. This makes 'ethtool -i'
show a more useful value than 'virtio' in the bus-info field.
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
A queue with a capacity of zero is clearly not a valid virtio queue.
Some emulators report zero queue size if queried with an invalid queue
index. Instead of crashing in this case let us just return -ENOENT. To
make that work properly, let us fix the notifier cleanup logic as well.
Cc: stable@vger.kernel.org
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Working with the vfio-ap driver let to some revisit of the way
how an ap (queue) device is removed from the driver.
With the current implementation all the cleanup was done before
the driver even got notified about the removal. Now the ap
queue removal is done in 3 steps:
1) A preparation step, all ap messages within the queue
are flushed and so the driver does 'receive' them.
Also a new state AP_STATE_REMOVE assigned to the queue
makes sure there are no new messages queued in.
2) Now the driver's remove function is invoked and the
driver should do the job of cleaning up it's internal
administration lists or whatever. After 2) is done
it is guaranteed, that the driver is not invoked any
more. On the other hand the driver has to make sure
that the APQN is not accessed any more after step 2
is complete.
3) Now the ap bus code does the job of total cleanup of the
APQN. A reset with zero is triggered and the state of
the queue goes to AP_STATE_UNBOUND.
After step 3) is complete, the ap queue has no pending
messages and the APQN is cleared and so there are no
requests and replies lingering around in the firmware
queue for this APQN. Also the interrupts are disabled.
After these remove steps the ap queue device may be assigned
to another driver.
Stress testing this remove/probe procedure showed a problem with the
correct module reference counting. The actual receive of an reply in
the driver is done asynchronous with completions. So with a driver
change on an ap queue the message flush triggers completions but the
threads waiting for the completions may run at a time where the queue
already has the new driver assigned. So the module_put() at receive
time needs to be done on the driver module which queued the ap
message. This change is also part of this patch.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Ingo Franzki <ifranzki@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
- A copy of Arnds compat wrapper generation series
- Pass information about the KVM guest to the host in form the control
program code and the control program version code
- Map IOV resources to support PCI physical functions on s390
- Add vector load and store alignment hints to improve performance
- Use the "jdd" constraint with gcc 9 to make jump labels working again
- Remove amode workaround for old z/VM releases from the DCSS code
- Add support for in-kernel performance measurements using the CPU
measurement counter facility
- Introduce a new PMU device cpum_cf_diag to capture counters and store
thenn as event raw data.
- Bug fixes and cleanups
* tag 's390-5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (54 commits)
Revert "s390/cpum_cf: Add kernel message exaplanations"
s390/dasd: fix read device characteristic with CONFIG_VMAP_STACK=y
s390/suspend: fix prefix register reset in swsusp_arch_resume
s390: warn about clearing als implied facilities
s390: allow overriding facilities via command line
s390: clean up redundant facilities list setup
s390/als: remove duplicated in-place implementation of stfle
s390/cio: Use cpa range elsewhere within vfio-ccw
s390/cio: Fix vfio-ccw handling of recursive TICs
s390: vfio_ap: link the vfio_ap devices to the vfio_ap bus subsystem
s390/cpum_cf: Handle EBUSY return code from CPU counter facility reservation
s390/cpum_cf: Add kernel message exaplanations
s390/cpum_cf_diag: Add support for s390 counter facility diagnostic trace
s390/cpum_cf: add ctr_stcctm() function
s390/cpum_cf: move common functions into a separate file
s390/cpum_cf: introduce kernel_cpumcf_avail() function
s390/cpu_mf: replace stcctm5() with the stcctm() function
s390/cpu_mf: add store cpu counter multiple instruction support
s390/cpum_cf: Add minimal in-kernel interface for counter measurements
s390/cpum_cf: introduce kernel_cpumcf_alert() to obtain measurement alerts
...
|
|
The dasd_eckd_restore_device() function calls dasd_generic_read_dev_chars
with a temporary buffer on the stack. With CONFIG_VMAP_STACK=y this is
a vmalloc address but dasd_generic_restore_device() uses the address of
the buffer as I/O address. Circumvent this by using the already allocated
cqr->data buffer for the RDC data.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Now that qeth always uses dev_close() to shutdown the interface, we can
trust the locking and remove some custom state checks.
qeth_l?_stop_card() is no longer called for a card in UP state, so remove
the checks there too. This basically makes the UP state obsolete, so rip
out the whole thing (except for the sysfs-visible string).
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It makes no difference whether we
1. manually disarm the HW trap and call the offline code with
recovery_mode == 1, or
2. call the offline code with recovery_mode == 0, and let it disarm the
HW trap for us.
So consolidate the two code paths in the suspend callback.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The qeth-wide workqueue is now only used by a single caller to schedule
close_dev work. Just put it on a system queue instead.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The recovery code already runs in a kthread, we don't have to defer the
offlining further.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
smatch complains that __qeth_l3_set_offline() first accesses card->dev,
and then later checks whether the pointer is valid.
Since commit d3d1b205e89f ("s390/qeth: allocate netdevice early"), the
pointer is _always_ valid - that patch merely missed to remove this one
check.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When resetting an interface ("recovery"), qeth currently attempts to
elide the call to dev_close(). We initially only call .ndo_close to
quiesce the data path, and then offline & online the ccwgroup device.
If the reset succeeded, a call to .ndo_open then resumes the data path
along with some internal setup (dev_addr validation, RX modeset) that
dev_open() would have usually triggered.
dev_close() only gets called (via the close_dev worker) if the reset
action fails.
It's unclear whether this was initially done due to locking concerns, or
rather to execute the reset transparently. Either way, temporarily
closing the interface without dev_close() is fragile, and means we're
susceptible to various races and unexpected behaviour. For instance:
- Bypassing dev_deactivate_many() means that the qdiscs are not set to
__QDISC_STATE_DEACTIVATED. Consequently any intermittent TX completion
can wake up the txq, resulting in calls to .ndo_start_xmit while the
data path is down. We have custom state checking to detect this case
and drop such packets.
- Because the IFF_UP flag doesn't reflect the interface's actual state
during a reset, we have custom state checking in .ndo_open and
.ndo_close to guard against invalid calls.
- Considering that the reset might take a considerable amount of time
(in particular if an IO fails and we end up waiting for its timeout), we
_do_ want NETDEV_GOING_DOWN and NETDEV_DOWN events so that components
like bonding, team, bridge, macvlan, vlan, ... can take appropriate
action.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In its attempt to run only the minimal amount of tear down steps,
qeth_l2_stop_card() fails to reset the "is dev_addr registered?" flag
in some rare scenarios. But a future change to the tear down sequence
would cause us to _always_ hit this issue, so patch it up before that
code lands.
Fix it by unconditionally clearing the flag bit. This also allows us to
remove the additional cleanup step in qeth_dev_layer2_store().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When setting a L2 qeth device online, enable the HW trap as soon as the
control plane is available. This allows us to catch any error that
occurs during the very first commands.
In the same spirit, the offline code should disable the HW trap as the
very first step of its processing.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The offline code uses a specific RECOVER state to indicate that the
interface should be brought up when a qeth device is set online again.
Rather than having a specific card-state for this, just put it in an
internal flag bit and set the state to DOWN. When working with the
card's state transitions, this reduces the complexity quite a bit.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since we have a little function to see whether a channel
program address falls within a range of CCWs, let's use
it in the other places of code that make these checks.
(Why isn't ccw_head fully removed? Well, because this
way some longs lines don't have to be reflowed.)
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Message-Id: <20190222183941.29596-3-farman@linux.ibm.com>
Reviewed-by: Farhan Ali <alifm@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
|
|
The routine ccwchain_calc_length() is tasked with looking at a
channel program, seeing how many CCWs are chained together by
the presence of the Chain-Command flag, and returning a count
to the caller.
Previously, it also considered a Transfer-in-Channel CCW as being
an appropriate mechanism for chaining. The problem at the time
was that the TIC CCW will almost certainly not go to the next CCW
in memory (because the CC flag would be sufficient), and so
advancing to the next 8 bytes will cause us to read potentially
invalid memory. So that comparison was removed, and the target
of the TIC is processed as a new chain.
This is fine when a TIC goes to a new chain (consider a NOP+TIC to
a channel program that is being redriven), but there is another
scenario where this falls apart. A TIC can be used to "rewind"
a channel program, for example to find a particular record on a
disk with various orientation CCWs. In this case, we DO want to
consider the memory after the TIC since the TIC will be skipped
once the requested criteria is met. This is due to the Status
Modifier presented by the device, though software doesn't need to
operate on it beyond understanding the behavior change of how the
channel program is executed.
So to handle this, we will re-introduce the check for a TIC CCW
but limit it by examining the target of the TIC. If the TIC
doesn't go back into the current chain, then current behavior
applies; we should stop counting CCWs and let the target of the
TIC be handled as a new chain. But, if the TIC DOES go back into
the current chain, then we need to keep looking at the memory after
the TIC for when the channel breaks out of the TIC loop. We can't
use tic_target_chain_exists() because the chain in question hasn't
been built yet, so we will redefine that comparison with some small
functions to make it more readable and to permit refactoring later.
Fixes: 405d566f98ae ("vfio-ccw: Don't assume there are more ccws after a TIC")
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Message-Id: <20190222183941.29596-2-farman@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Farhan Ali <alifm@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into kvm-next
KVM: s390: Features for 5.1
- Clarify KVM related kernel messages
- Interrupt cleanup
- Introduction of the Guest Information Block (GIB)
- Preparation for processor subfunctions in cpu model
|
|
Libudev relies on having a subsystem link for non-root devices. To
avoid libudev (and potentially other userspace tools) choking on the
matrix device let us introduce a matrix bus and with it the matrix
bus subsytem. Also make the matrix device reside within the matrix
bus.
Doing this we remove the forced link from the matrix device to the
vfio_ap driver and the device_type we do not need anymore.
Since the associated matrix driver is not the vfio_ap driver any more,
we have to change the search for the devices on the vfio_ap driver in
the function vfio_ap_verify_queue_reserved.
Fixes: 1fde573413b5 ("s390: vfio-ap: base implementation of VFIO AP device driver")
Cc: stable@vger.kernel.org
Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
When the CCA master key is set twice with the same master key,
then the old and the current master key are the same and thus the
verification patterns are the same, too. The check to report if a
secure key is currently wrapped by the old master key erroneously
reports old mkvp in this case.
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Ingo Franzki <ifranzki@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Prior to dma unmap/free operations the ism driver tries to ensure
that the memory is no longer accessed by the HW. When errors
during deregistration of memory regions from the HW occur the ism
driver will not unmap/free this memory.
When we receive notification from the hypervisor that a PCI function
has been detached we can no longer access the device and would never
unmap/free these memory regions which led to complaints by the DMA
debug API.
Treat this kind of errors during the deregistration of memory regions
from the HW as success since it is already ensured that the memory
is no longer accessed by HW.
Reported-by: Karsten Graul <kgraul@linux.ibm.com>
Reported-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Rather than special-casing OSN in a number of places, just give this
device type its own netdev_ops structure.
When setting up the OSN net_device, also skip the handling of the
various HW offloads (eg TSO). The device shouldn't be advertising any of
them, and the OSN code paths in qeth don't have support for them.
In particular RX VLAN filtering is not supported, so don't hook up those
callbacks in the netdev_ops.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement a trivial callback that exposes the queue sizes.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Accumulate per-TX queue statistics, and increase their size to 64 bit.
Don't bother with enabling/disabling the statistics, the overhead is
negligible.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of this is self-contained code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Counting the number of function calls and the time spent in functions
is best left to proper tracing facilities.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qeth dynamically allocates an array for storing pointers to its
Output Queue structures. Switch this to a static array - we are
currently limited to 4 Output Queues, so shrinking the qeth_qdio_info
struct by just a few bytes doesn't justify the additional complexity.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Once a qeth ccwgroup device is set online, it's also armed for internal
recovery. So allow for testing that code path via sysfs, regardless of
whether the interface is up or down.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an alternate driver (vfio-ap) has bound an ap queue and this
binding is revised the ap queue device is in an intermittent
state not bound to any driver. The internal state variable
covered this with the state AP_STATE_BORKED which is also used to
reflect broken devices. When now an ap bus scan runs such a
device is destroyed and on the next scan reconstructed.
So a stress test with high frequency switching the queue driver
between the default and the vfio-ap driver hit this gap and the
queue was removed until the next ap bus scan. This fix now
introduces another state for the in-between condition for a queue
momentary not bound to a driver and so the ap bus scan function
skips this device instead of removing it.
Also some very slight but maybe helpful debug feature messages
come with this patch - in particular a message showing that a
broken card/queue device will get removed.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Ingo Franzki <ifranzki@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This calls the existing errno translation helpers from the callbacks,
adding trivial wrappers where necessary. For cmds that have no
sophisticated errno translation, default to -EIO.
For IPA cmds with no callback, fall back to a minimal default. This is
currently being used by qeth_l3_send_setrouting().
Thus having all converted all callbacks, remove the legacy path in
qeth_send_control_data_cb().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By letting the callbacks deal with error translation, we no longer need
to pass the raw error codes back to the originator. This allows us to
slim down the callback's private data, and nicely simplifies the code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Error propagation from cmd callbacks currently works in a way where
qeth_send_control_data_cb() picks the raw HW code from the response,
and the cmd's originator later translates this into an errno.
The callback itself only returns 0 ("done") or 1 ("expect more data").
This is
1. limiting, as the only means for the callback to report an internal
error is to invent pseudo HW codes (such as IPA_RC_ENOMEM), that
the originator then needs to understand. For non-IPA callbacks, we
even provide a separate field in the IO buffer metadata (iob->rc) so
the callback can pass back a return value.
2. fragile, as the originator must take care to not translate any errno
that is returned by qeth's own IO code paths (eg -ENOMEM). Also, any
originator that forgets to translate the HW codes potentially passes
garbage back to its caller. For instance, see
commit 2aa4867198c2 ("s390/qeth: translate SETVLAN/DELVLAN errors").
Introduce a new model where all HW error translation is done within the
callback, and the callback returns
> 0, if it expects more data (as before)
== 0, on success
< 0, with an errno
Start off with converting all callbacks to the new model that either
a) pass back pseudo HW codes, or b) have a dependency on a specific
HW error code. Also convert c) the one callback that uses iob->rc, and
d) qeth_setadpparms_change_macaddr_cb() so that it can pass back an
error back to qeth_l2_request_initial_mac() even when the cmd itself
was successful.
The old model remains supported: if the callback returns 0, we still
propagate the response's HW error code back to the originator.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
