Merge branch 'tracking-qcomlt-hsuart' into integration-linux-qcomlt

* tracking-qcomlt-hsuart:
  tty: serial: msm: Unlock interrupts during SysRq processing
  tty: serial: msm: Remove 115.2 Kbps maximum baud rate limitation
  tty: serial: msm: Add RX DMA support
  tty: serial: msm: Add TX DMA support
  tty: serial: msm: Add msm prefix to all driver functions
  tty: serial: msm: Fix command Stale Event Enable definition
  tty: serial: msm: replaces (1 << x) with BIT(x) macro
  tty: serial: msm: Add mask value for UART_DM registers
  dmaengine: adm: Start next DMA even if there is no ongoing transaction
  dmaengine: adm: Don't reset controller during probe
  dmaengine: adm: Use 'soft' flush when stopping DMA
  dmaengine: adm: Fix ADM hardware descriptor creation when flow control is enabled
  dmaengine: Add ADM driver
  dt/bindings: qcom_adm: Fix channel specifiers

2 files changed, 12 insertions, 10 deletions

diff --git a/Documentation/devicetree/bindings/dma/qcom_adm.txt b/Documentation/devicetree/bindings/dma/qcom_adm.txt
index 9bcab9115982..38d45f8a0dc8 100644
--- a/Documentation/devicetree/bindings/dma/qcom_adm.txt
+++ b/Documentation/devicetree/bindings/dma/qcom_adm.txt
@@ -4,8 +4,7 @@ Required properties:
 - compatible: must contain "qcom,adm" for IPQ/APQ8064 and MSM8960
 - reg: Address range for DMA registers
 - interrupts: Should contain one interrupt shared by all channels
-- #dma-cells: must be <2>.  First cell denotes the channel number.  Second cell
-  denotes CRCI (client rate control interface) flow control assignment.
+- #dma-cells: must be <1>.  First cell denotes the channel number.
 - clocks: Should contain the core clock and interface clock.
 - clock-names: Must contain "core" for the core clock and "iface" for the
   interface clock.
@@ -22,7 +21,7 @@ Example:
 			compatible = "qcom,adm";
 			reg = <0x18300000 0x100000>;
 			interrupts = <0 170 0>;
-			#dma-cells = <2>;
+			#dma-cells = <1>;
 
 			clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
 			clock-names = "core", "iface";
@@ -35,15 +34,12 @@ Example:
 			qcom,ee = <0>;
 		};
 
-DMA clients must use the format descripted in the dma.txt file, using a three
+DMA clients must use the format descripted in the dma.txt file, using a two
 cell specifier for each channel.
 
-Each dmas request consists of 3 cells:
+Each dmas request consists of two cells:
  1. phandle pointing to the DMA controller
  2. channel number
- 3. CRCI assignment, if applicable.  If no CRCI flow control is required, use 0.
-    The CRCI is used for flow control.  It identifies the peripheral device that
-    is the source/destination for the transferred data.
 
 Example:
 
@@ -56,7 +52,7 @@ Example:
 
 		cs-gpios = <&qcom_pinmux 20 0>;
 
-		dmas = <&adm_dma 6 9>,
-			<&adm_dma 5 10>;
+		dmas = <&adm_dma 6>,
+			<&adm_dma 5>;
 		dma-names = "rx", "tx";
 	};
diff --git a/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt
index a2114c217376..182777fac9a2 100644
--- a/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt
+++ b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt
@@ -26,6 +26,12 @@ Required properties:
 Optional properties:
 - dmas: Should contain dma specifiers for transmit and receive channels
 - dma-names: Should contain "tx" for transmit and "rx" for receive channels
+- qcom,tx-crci: Identificator <u32> for Client Rate Control Interface to be
+           used with TX DMA channel. Required when using DMA for transmission
+           with UARTDM v1.3 and bellow.
+- qcom,rx-crci: Identificator <u32> for Client Rate Control Interface to be
+           used with RX DMA channel. Required when using DMA for reception
+           with UARTDM v1.3 and bellow.
 
 Note: Aliases may be defined to ensure the correct ordering of the UARTs.
 The alias serialN will result in the UART being assigned port N.  If any