diff options
Diffstat (limited to 'Documentation/devicetree')
19 files changed, 697 insertions, 10 deletions
diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index 91e6e5c478d0..259c50f0a720 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -185,6 +185,8 @@ nodes to be present and contain the properties described below. be one of: "psci" "spin-table" + "qcom,arm-cortex-acc" + # On ARM 32-bit systems this property is optional and can be one of: "allwinner,sun6i-a31" diff --git a/Documentation/devicetree/bindings/arm/msm/acc.txt b/Documentation/devicetree/bindings/arm/msm/acc.txt new file mode 100644 index 000000000000..ae2d7253b363 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/msm/acc.txt @@ -0,0 +1,19 @@ +Application Processor Sub-system (APSS) Application Clock Controller (ACC) + +The ACC provides clock, power domain, and reset control to a CPU. There is one ACC +register region per CPU within the APSS remapped region as well as an alias register +region that remaps accesses to the ACC associated with the CPU accessing the region. + +Required properties: +- compatible: Must be "qcom,arm-cortex-acc" +- reg: The first element specifies the base address and size of + the register region. An optional second element specifies + the base address and size of the alias register region. + +Example: + + clock-controller@b088000 { + compatible = "qcom,arm-cortex-acc"; + reg = <0x0b088000 0x1000>, + <0x0b008000 0x1000>; + } diff --git a/Documentation/devicetree/bindings/arm/msm/ids.txt b/Documentation/devicetree/bindings/arm/msm/ids.txt new file mode 100644 index 000000000000..9ee8428f4670 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/msm/ids.txt @@ -0,0 +1,65 @@ +* MSM-ID + +The qcom,msm-id entry specifies the MSM chipset and hardware revision. It can +optionally be an array of these to indicate multiple hardware that use the same +device tree. It is expected that the bootloader will use this information at +boot-up to decide which device tree to use when given multiple device trees, +some of which may not be compatible with the actual hardware. It is the +bootloader's responsibility to pass the correct device tree to the kernel. + +PROPERTIES + +- qcom,msm-id: + Usage: required + Value type: <prop-encoded-array> (<chipset_id, rev_id> [, <c2, r2> ..]) + Definition: + The "chipset_id" consists of three fields as below: + + bits 0-15 = The unique MSM chipset id. + bits 16-31 = Reserved. Should be 0 + + chipset_id is an exact match value + + The "rev_id" is a chipset specific 32-bit id that represents + the version of the chipset. + + The rev_id is a best match id. The bootloader will look for + the closest possible patch. + +* BOARD-ID + +The qcom,board-id entry specifies the board type and revision information. It +can optionally be an array of these to indicate multiple boards that use the +same device tree. It is expected that the bootloader will use this information +at boot-up to decide which device tree to use when given multiple device trees, +some of which may not be compatible with the actual hardware. It is the +bootloader's responsibility to pass the correct device tree to the kernel. + +PROPERTIES + +- qcom,board-id: + Usage: required + Value type: <prop-encoded-array> (<board_id, subtype_id> [, <b2, s2> ..]) + Definition: + The "board_id" consists of three fields as below: + + bits 31-24 = Unusued. + bits 23-16 = Platform Version Major + bits 15-8 = Platfrom Version Minor + bits 7-0 = Platform Type + + Platform Type field is an exact match value. The Platform + Major/Minor field is a best match. The bootloader will look + for the closest possible match. + + The "subtype_id" is unique to a Platform Type/Chipset ID. For + a given Platform Type, there will typically only be a single + board and the subtype_id will be 0. However in some cases board + variants may need to be distinquished by different subtype_id + values. + + subtype_id is an exact match value. + +EXAMPLE: + qcom,board-id = <15 2>; + qcom,msm-id = <0x1007e 0>; diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt b/Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt index 1333db9acfee..382a574a5c55 100644 --- a/Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt +++ b/Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt @@ -21,10 +21,17 @@ PROPERTIES the register region. An optional second element specifies the base address and size of the alias register region. +- clock-output-names: + Usage: optional + Value type: <string> + Definition: Name of the output clock. Typically acpuX_aux where X is a + CPU number starting at 0. + Example: clock-controller@2088000 { compatible = "qcom,kpss-acc-v2"; reg = <0x02088000 0x1000>, <0x02008000 0x1000>; + clock-output-names = "acpu0_aux"; }; diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,kpss-gcc.txt b/Documentation/devicetree/bindings/arm/msm/qcom,kpss-gcc.txt new file mode 100644 index 000000000000..d1e12f16a28c --- /dev/null +++ b/Documentation/devicetree/bindings/arm/msm/qcom,kpss-gcc.txt @@ -0,0 +1,28 @@ +Krait Processor Sub-system (KPSS) Global Clock Controller (GCC) + +PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: should be one of: + "qcom,kpss-gcc" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: base address and size of the register region + +- clock-output-names: + Usage: required + Value type: <string> + Definition: Name of the output clock. Typically acpu_l2_aux indicating + an L2 cache auxiliary clock. + +Example: + + l2cc: clock-controller@2011000 { + compatible = "qcom,kpss-gcc"; + reg = <0x2011000 0x1000>; + clock-output-names = "acpu_l2_aux"; + }; diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,pvs.txt b/Documentation/devicetree/bindings/arm/msm/qcom,pvs.txt new file mode 100644 index 000000000000..e7cb10426a3b --- /dev/null +++ b/Documentation/devicetree/bindings/arm/msm/qcom,pvs.txt @@ -0,0 +1,38 @@ +Qualcomm Process Voltage Scaling Tables + +The node name is required to be "qcom,pvs". There shall only be one +such node present in the root of the tree. + +PROPERTIES + +- qcom,pvs-format-a or qcom,pvs-format-b: + Usage: required + Value type: <empty> + Definition: Indicates the format of qcom,speedX-pvsY-bin-vZ properties. + If qcom,pvs-format-a is used the table is two columns + (frequency and voltage in that order). If qcom,pvs-format-b is used the table is three columns (frequency, voltage, + and current in that order). + +- qcom,speedX-pvsY-bin-vZ: + Usage: required + Value type: <prop-encoded-array> + Definition: The PVS table corresponding to the speed bin X, pvs bin Y, + and version Z. +Example: + + qcom,pvs { + qcom,pvs-format-a; + qcom,speed0-pvs0-bin-v0 = + < 384000000 950000 >, + < 486000000 975000 >, + < 594000000 1000000 >, + < 702000000 1025000 >, + < 810000000 1075000 >, + < 918000000 1100000 >, + < 1026000000 1125000 >, + < 1134000000 1175000 >, + < 1242000000 1200000 >, + < 1350000000 1225000 >, + < 1458000000 1237500 >, + < 1512000000 1250000 >; + }; diff --git a/Documentation/devicetree/bindings/clock/qcom,a53cc b/Documentation/devicetree/bindings/clock/qcom,a53cc new file mode 100644 index 000000000000..209cae8afc1f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,a53cc @@ -0,0 +1,22 @@ +A53 Clock Controller + +Required properties : +- compatible : shall contain: + "qcom,a53cc" +- reg : shall contain base register location and length + of the A53 PLL +- #clock-cells : shall contain 1 +- qcom,apcs : phandle of apcs syscon node + +Example: + apcs: syscon@b011000 { + compatible = "syscon"; + reg = <0x0b011000 0x1000>; + }; + + a53cc: clock-controller@0b016000 { + compatible = "qcom,clock-a53-msm8916"; + reg = <0x0b016000 0x40>; + #clock-cells = <1>; + qcom,apcs = <&apcs>; + }; diff --git a/Documentation/devicetree/bindings/clock/qcom,hfpll.txt b/Documentation/devicetree/bindings/clock/qcom,hfpll.txt new file mode 100644 index 000000000000..fee92bb30344 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,hfpll.txt @@ -0,0 +1,40 @@ +High-Frequency PLL (HFPLL) + +PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: must be "qcom,hfpll" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: address and size of HPLL registers. An optional second + element specifies the address and size of the alias + register region. + +- clock-output-names: + Usage: required + Value type: <string> + Definition: Name of the PLL. Typically hfpllX where X is a CPU number + starting at 0. Otherwise hfpll_Y where Y is more specific + such as "l2". + +Example: + +1) An HFPLL for the L2 cache. + + clock-controller@f9016000 { + compatible = "qcom,hfpll"; + reg = <0xf9016000 0x30>; + clock-output-names = "hfpll_l2"; + }; + +2) An HFPLL for CPU0. This HFPLL has the alias register region. + + clock-controller@f908a000 { + compatible = "qcom,hfpll"; + reg = <0xf908a000 0x30>, <0xf900a000 0x30>; + clock-output-names = "hfpll0"; + }; diff --git a/Documentation/devicetree/bindings/clock/qcom,krait-cc.txt b/Documentation/devicetree/bindings/clock/qcom,krait-cc.txt new file mode 100644 index 000000000000..874138f88ec6 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,krait-cc.txt @@ -0,0 +1,22 @@ +Krait Clock Controller + +PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,krait-cc-v1" + "qcom,krait-cc-v2" + +- #clock-cells: + Usage: required + Value type: <u32> + Definition: must be 1 + +Example: + + kraitcc: clock-controller { + compatible = "qcom,krait-cc-v1"; + #clock-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt b/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt new file mode 100644 index 000000000000..ceef5e66fa24 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt @@ -0,0 +1,15 @@ +Qualcomm RPM Clock Controller Binding +------------------------------------------------ + +Required properties : +- compatible : shall contain only one of the following: + + "qcom,rpmcc-msm8916" + +- #clock-cells : shall contain 1 + +Example: + rpmcc: rpmcc { + compatible = "qcom,rpmcc-msm8916"; + #clock-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/dma/qcom_adm.txt b/Documentation/devicetree/bindings/dma/qcom_adm.txt index 9bcab9115982..38d45f8a0dc8 100644 --- a/Documentation/devicetree/bindings/dma/qcom_adm.txt +++ b/Documentation/devicetree/bindings/dma/qcom_adm.txt @@ -4,8 +4,7 @@ Required properties: - compatible: must contain "qcom,adm" for IPQ/APQ8064 and MSM8960 - reg: Address range for DMA registers - interrupts: Should contain one interrupt shared by all channels -- #dma-cells: must be <2>. First cell denotes the channel number. Second cell - denotes CRCI (client rate control interface) flow control assignment. +- #dma-cells: must be <1>. First cell denotes the channel number. - clocks: Should contain the core clock and interface clock. - clock-names: Must contain "core" for the core clock and "iface" for the interface clock. @@ -22,7 +21,7 @@ Example: compatible = "qcom,adm"; reg = <0x18300000 0x100000>; interrupts = <0 170 0>; - #dma-cells = <2>; + #dma-cells = <1>; clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>; clock-names = "core", "iface"; @@ -35,15 +34,12 @@ Example: qcom,ee = <0>; }; -DMA clients must use the format descripted in the dma.txt file, using a three +DMA clients must use the format descripted in the dma.txt file, using a two cell specifier for each channel. -Each dmas request consists of 3 cells: +Each dmas request consists of two cells: 1. phandle pointing to the DMA controller 2. channel number - 3. CRCI assignment, if applicable. If no CRCI flow control is required, use 0. - The CRCI is used for flow control. It identifies the peripheral device that - is the source/destination for the transferred data. Example: @@ -56,7 +52,7 @@ Example: cs-gpios = <&qcom_pinmux 20 0>; - dmas = <&adm_dma 6 9>, - <&adm_dma 5 10>; + dmas = <&adm_dma 6>, + <&adm_dma 5>; dma-names = "rx", "tx"; }; diff --git a/Documentation/devicetree/bindings/drm/msm/dsi.txt b/Documentation/devicetree/bindings/drm/msm/dsi.txt index d56923cd5590..febcc516200d 100644 --- a/Documentation/devicetree/bindings/drm/msm/dsi.txt +++ b/Documentation/devicetree/bindings/drm/msm/dsi.txt @@ -44,6 +44,17 @@ Optional properties: - port: DSI controller output port. This contains one endpoint subnode, with its remote-endpoint set to the phandle of the connected panel's endpoint. See Documentation/devicetree/bindings/graph.txt for device graph info. +- qcom,dsi-logical-lane-swap: Character string to swap logical lane to physical + lane mapping. Supported lane mappings: + "0123": Logic 0->Phys 0; Logic 1->Phys 1; Logic 2->Phys 2; Logic 3->Phys 3; + "3012": Logic 3->Phys 0; Logic 0->Phys 1; Logic 1->Phys 2; Logic 2->Phys 3; + "2301": Logic 2->Phys 0; Logic 3->Phys 1; Logic 0->Phys 2; Logic 1->Phys 3; + "1230": Logic 1->Phys 0; Logic 2->Phys 1; Logic 3->Phys 2; Logic 0->Phys 3; + "0321": Logic 0->Phys 0; Logic 3->Phys 1; Logic 2->Phys 2; Logic 1->Phys 3; + "1032": Logic 1->Phys 0; Logic 0->Phys 1; Logic 3->Phys 2; Logic 2->Phys 3; + "2103": Logic 2->Phys 0; Logic 1->Phys 1; Logic 0->Phys 2; Logic 3->Phys 3; + "3210": Logic 3->Phys 0; Logic 2->Phys 1; Logic 1->Phys 2; Logic 0->Phys 3; + Default value is "0123", which means no lane swap. DSI PHY: Required properties: @@ -129,6 +140,8 @@ Example: remote-endpoint = <&panel_in>; }; }; + + qcom,dsi-logical-lane-swap = "0123"; }; mdss_dsi_phy0: qcom,mdss_dsi_phy@fd922a00 { diff --git a/Documentation/devicetree/bindings/gpio/qcom,smp2p.txt b/Documentation/devicetree/bindings/gpio/qcom,smp2p.txt new file mode 100644 index 000000000000..e758c8b5e3fc --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/qcom,smp2p.txt @@ -0,0 +1,105 @@ +Qualcomm Shared Memory Point 2 Point binding + +The Shared Memory Point to Point (SMP2P) protocol facilitates communication of +a single 32-bit value between two processors. Each value has a single writer +(the local side) and a single reader (the remote side). Values are uniquely +identified in the system by the directed edge (local processor ID to remote +processor ID) and a string identifier. This documents defines the binding for a +driver that implements and exposes this protocol as a set of GPIO and interrupt +controllers. + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,smp2p" + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: one entry specifying the smp2p notification interrupt + +- qcom,ipc: + Usage: required + Value type: <prop-encoded-array> + Definition: three entries specifying the outgoing ipc bit used for + signaling the remote end of the smp2p edge: + - phandle to a syscon node representing the apcs registers + - u32 representing offset to the register within the syscon + - u32 representing the ipc bit within the register + +- qcom,smem: + Usage: required + Value type: <u32 array> + Definition: two identifiers of the inbound and outbound smem items used + for this edge + +- qcom,local-pid: + Usage: required + Value type: <u32> + Definition: specifies the identfier of the local endpoint of this edge + +- qcom,remote-pid: + Usage: required + Value type: <u32> + Definition: specifies the identfier of the remote endpoint of this edge + += SUBNODES +Each SMP2P pair contain a set of inbound and outbound entries, these are +described in subnodes of the smp2p device node. The node names are not +important. + +- qcom,entry-name: + Usage: required + Value type: <string> + Definition: specifies the name of this entry, for inbound entries this + will be used to match against the remotely allocated entry + and for outbound entries this name is used for allocating + entries + +- qcom,inbound: + Usage: optional + Value type: <empty> + Definition: marks the entry as inbound; the node should be specified + as a two cell interrupt-controller as defined in + "../interrupt-controller/interrupts.txt" + +- qcom,outbound: + Usage: optional + Value type: <empty> + Definition: marks the entry as outbound; the node should be specified + as a two cell gpio-controller as defined in "gpio.txt" + + += EXAMPLE +The following example shows the SMP2P setup with the wireless processor, +defined from the 8974 apps processor's point-of-view. It encompasses one +inbound and one outbound entry: + +wcnss-smp2p { + compatible = "qcom,smp2p"; + qcom,smem = <431>, <451>; + + interrupts = <0 143 1>; + + qcom,ipc = <&apcs 8 18>; + + qcom,local-pid = <0>; + qcom,remote-pid = <4>; + + wcnss_smp2p_out: master-kernel { + qcom,entry-name = "master-kernel"; + qcom,outbound; + + gpio-controller; + #gpio-cells = <2>; + }; + + wcnss_smp2p_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + qcom,inbound; + + interrupt-controller; + #interrupt-cells = <2>; + }; +}; diff --git a/Documentation/devicetree/bindings/iommu/msm,iommu-v0.txt b/Documentation/devicetree/bindings/iommu/msm,iommu-v0.txt new file mode 100644 index 000000000000..21bfbfcc5ae3 --- /dev/null +++ b/Documentation/devicetree/bindings/iommu/msm,iommu-v0.txt @@ -0,0 +1,59 @@ +* QCOM IOMMU + +The QCOM IOMMU is an implementation compatible with the ARM VMSA short +descriptor page tables. It provides address translation for bus masters outside +of the CPU, each connected to the IOMMU through a port called micro-TLB. + +Required Properties: + + - compatible: Must contain "qcom,iommu-v0". + - reg: Base address and size of the IOMMU registers. + - interrupts: Specifiers for the MMU fault interrupts. For instances that + support secure mode two interrupts must be specified, for non-secure and + secure mode, in that order. For instances that don't support secure mode a + single interrupt must be specified. + - #iommu-cells: This is the total number of stream ids that a master would + use during transactions which will be specified as a list + as a part of iommus property below. + - ncb: The total number of context banks in the IOMMU. + - clocks : List of clocks to be used during SMMU register access. See + Documentation/devicetree/bindings/clock/clock-bindings.txt + for information about the format. For each clock specified + here, there must be a corresponding entry in clock-names + (see below). + + - clock-names : List of clock names corresponding to the clocks specified in + the "clocks" property (above). See + Documentation/devicetree/bindings/clock/clock-bindings.txt + for more info. + +Each bus master connected to an IOMMU must reference the IOMMU in its device +node with the following property: + + - iommus: A reference to the IOMMU in multiple cells. The first cell is a + phandle to the IOMMU and the second cell is the list of the + stream ids used by the device. + +Example: mdp iommu and its bus master + + mdp_port0: qcom,iommu@7500000 { + compatible = "msm,iommu-v0"; + #iommu-cells = <2>; + clock-names = + "smmu_pclk", + "iommu_clk"; + clocks = + <&mmcc SMMU_AHB_CLK>, + <&mmcc MDP_AXI_CLK>; + reg = <0x07500000 0x100000>; + interrupts = + <GIC_SPI 63 0>, + <GIC_SPI 64 0>; + ncb = <2>; + }; + + mdp: qcom,mdp@5100000 { + compatible = "qcom,mdp"; + ... + iommus = <&mdp_port0 0 2>; + }; diff --git a/Documentation/devicetree/bindings/mfd/qcom-rpm-smd.txt b/Documentation/devicetree/bindings/mfd/qcom-rpm-smd.txt new file mode 100644 index 000000000000..2e28f350c548 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/qcom-rpm-smd.txt @@ -0,0 +1,156 @@ +Qualcomm Resource Power Manager (RPM) over SMD + +This driver is used to interface with the Resource Power Manager (RPM) found in +various Qualcomm platforms. The RPM allows each component in the system to vote +for state of the system resources, such as clocks, regulators and bus +frequencies. + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,rpm-msm8974" + "qcom,rpm-msm8916" + +- qcom,smd-channels: + Usage: required + Value type: <stringlist> + Definition: Shared Memory channel used for communication with the RPM + += SUBDEVICES + +The RPM exposes resources to its subnodes. The below bindings specify the set +of valid subnodes that can operate on these resources. + +== Regulators + +Regulator nodes are identified by their compatible: + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,rpm-pm8841-regulators" + "qcom,rpm-pm8941-regulators" + "qcom,rpm-pm8916-regulators" + +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: +- vdd_s4-supply: +- vdd_s5-supply: +- vdd_s6-supply: +- vdd_s7-supply: +- vdd_s8-supply: + Usage: optional (pm8841 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: +- vdd_l1_l3-supply: +- vdd_l2_lvs1_2_3-supply: +- vdd_l1_l3-supply: +- vdd_l4_l11-supply: +- vdd_l5_l7-supply: +- vdd_l6_l12_l14_l15-supply: +- vdd_l5_l7-supply: +- vdd_l8_l16_l18_l19-supply: +- vdd_l9_l10_l17_l22-supply: +- vdd_l9_l10_l17_l22-supply: +- vdd_l4_l11-supply: +- vdd_l6_l12_l14_l15-supply: +- vdd_l13_l20_l23_l24-supply: +- vdd_l6_l12_l14_l15-supply: +- vdd_l6_l12_l14_l15-supply: +- vdd_l8_l16_l18_l19-supply: +- vdd_l9_l10_l17_l22-supply: +- vdd_l8_l16_l18_l19-supply: +- vdd_l8_l16_l18_l19-supply: +- vdd_l13_l20_l23_l24-supply: +- vdd_l21-supply: +- vdd_l9_l10_l17_l22-supply: +- vdd_l13_l20_l23_l24-supply: +- vdd_l13_l20_l23_l24-supply: +- vdd_l2_lvs1_2_3-supply: +- vdd_l2_lvs1_2_3-supply: +- vdd_l2_lvs1_2_3-supply: +- vin_5vs-supply: +- vin_5vs-supply: + Usage: optional (pm8941 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: +- vdd_s4-supply: +- l1_l2_l3-supply: +- l4_l5_l6-supply: +- l7-supply: +- l8_l9_l10_l11_l12_l13_l14_l15_l16_l17_l18-supply: + + Usage: optional (pm8916 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + +The regulator node houses sub-nodes for each regulator within the device. Each +sub-node is identified using the node's name, with valid values listed for each +of the pmics below. + +pm8841: + s1, s2, s3, s4, s5, s6, s7, s8 + +pm8941: + s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, + l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, + lvs3, 5vs1, 5vs2 + +pm8916: + s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, + l14, l15, l16, l17, l18 + +The content of each sub-node is defined by the standard binding for regulators - +see regulator.txt. + += EXAMPLE + + smd { + compatible = "qcom,smd"; + + rpm { + interrupts = <0 168 1>; + qcom,ipc = <&apcs 8 0>; + qcom,smd-edge = <15>; + + rpm_requests { + compatible = "qcom,rpm-msm8974"; + qcom,smd-channels = "rpm_requests"; + + pm8941-regulators { + compatible = "qcom,rpm-pm8941-regulators"; + vdd_l13_l20_l23_l24-supply = <&pm8941_boost>; + + pm8941_s3: s3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + pm8941_boost: s4 { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + pm8941_l20: l20 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + }; + }; + }; + }; + }; + diff --git a/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt index a2114c217376..182777fac9a2 100644 --- a/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt +++ b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt @@ -26,6 +26,12 @@ Required properties: Optional properties: - dmas: Should contain dma specifiers for transmit and receive channels - dma-names: Should contain "tx" for transmit and "rx" for receive channels +- qcom,tx-crci: Identificator <u32> for Client Rate Control Interface to be + used with TX DMA channel. Required when using DMA for transmission + with UARTDM v1.3 and bellow. +- qcom,rx-crci: Identificator <u32> for Client Rate Control Interface to be + used with RX DMA channel. Required when using DMA for reception + with UARTDM v1.3 and bellow. Note: Aliases may be defined to ensure the correct ordering of the UARTs. The alias serialN will result in the UART being assigned port N. If any diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smem.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smem.txt new file mode 100644 index 000000000000..19cad6cc427c --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smem.txt @@ -0,0 +1,51 @@ +Qualcomm Shared Memory Manager binding + +This binding describes the Qualcomm Shared Memory Manager, used to share data +between various subsystems and OSes in Qualcomm platforms. + +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be: + "qcom,smem" + +- memory-region: + Usage: required + Value type: <prop-encoded-array> + Definition: handle to memory reservation for main SMEM memory region. + +- reg: + Usage: optional + Value type: <prop-encoded-array> + Definition: base address and size pair for any additional memory areas + of the shared memory. + +- hwlocks: + Usage: required + Value type: <prop-encoded-array> + Definition: reference to a hwspinlock used to protect allocations from + the shared memory + += EXAMPLE +The following example shows the SMEM setup for MSM8974, with a main SMEM region +at 0xfa00000 and an auxiliary region at 0xfc428000: + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + smem_region: smem@fa00000 { + reg = <0xfa00000 0x200000>; + no-map; + }; + }; + + smem@fa00000 { + compatible = "qcom,smem"; + + memory-region = <&smem_region>; + reg = <0xfc428000 0x4000>; + + hwlocks = <&tcsr_mutex 3>; + }; diff --git a/Documentation/devicetree/bindings/thermal/qcom-tsens.txt b/Documentation/devicetree/bindings/thermal/qcom-tsens.txt new file mode 100644 index 000000000000..cfb79fc80316 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/qcom-tsens.txt @@ -0,0 +1,37 @@ +* QCOM SoC Temperature Sensor (TSENS) + +Required properties: +- compatible : + - "qcom,msm8916-tsens" : For 8916 Family of SoCs + - "qcom,msm8974-tsens" : For 8974 Family of SoCs + - "qcom,msm8960-tsens" : For 8960 Family of SoCs + +- reg: Address range of the thermal registers +- qcom,tsens-slopes : Must contain slope value for each of the sensors controlled + by this device +- #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description. +- Refer to Documentation/devicetree/bindings/eeprom/eeprom.txt to know how to specify +an eeprom cell + +Optional properties: +- qcom,sensor-id: List of sensor instances used in a given SoC. A TSENS IP can + have a fixed number of sensors (like 11) but a given SoC can + use only 5 of these and they might not always the first 5. They + could be sensors 0, 1, 4, 8 and 9. This property is used to + describe the subset of the sensors used. If this property is + missing they are assumed to be the first 'n' sensors numbered + sequentially in which case the number of sensors defaults to + the number of slope values. + +Example: +tsens: thermal-sensor@900000 { + compatible = "qcom,msm8916-tsens"; + qcom,tsens-slopes = <1176 1176 1154 1176 1111 + 1132 1132 1199 1132 1199 + 1132>; + calib_data = <&tsens_caldata>; + calib_sel = <&tsens_calsel>; + qcom,tsens-slopes = <3200 3200 3200 3200 3200>; + qcom,sensor-id = <0 1 2 4 5>; + #thermal-sensor-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index a057b75ba4b5..db48bad84228 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -46,6 +46,11 @@ Optional properties: (4 bytes), This register represents the maximum length of a the burst in 32-bit words while moving data from the USB bus to system memory, changing this value takes effect only the SBUSCFG.AHBBRST is 0. +- extcon: phandles to external connector devices. First phandle should point to + external connector, which provide "USB" cable events, the second should point + to external connector device, which provide "USB-HOST" cable events. If one + of the external connector devices is not required, empty <0> phandle should + be specified. Example: @@ -62,4 +67,5 @@ Example: ahb-burst-config = <0x0>; tx-burst-size-dword = <0x10>; /* 64 bytes */ rx-burst-size-dword = <0x10>; + extcon = <0>, <&usb_id>; }; |