diff options
-rw-r--r-- | Documentation/devicetree/bindings/i2c/i2c-qcom-cci.txt | 91 | ||||
-rw-r--r-- | arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi | 112 | ||||
-rw-r--r-- | arch/arm64/boot/dts/qcom/msm8916.dtsi | 27 | ||||
-rw-r--r-- | arch/arm64/configs/defconfig | 2 | ||||
-rw-r--r-- | drivers/i2c/busses/Kconfig | 10 | ||||
-rw-r--r-- | drivers/i2c/busses/Makefile | 1 | ||||
-rw-r--r-- | drivers/i2c/busses/i2c-qcom-cci.c | 781 |
7 files changed, 1024 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/i2c/i2c-qcom-cci.txt b/Documentation/devicetree/bindings/i2c/i2c-qcom-cci.txt new file mode 100644 index 000000000000..ca8b9ab949f1 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-qcom-cci.txt @@ -0,0 +1,91 @@ +Qualcomm Camera Control Interface (CCI) I2C controller + +PROPERTIES: + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,msm8916-cci" + "qcom,msm8996-cci" + +- reg + Usage: required + Value type: <prop-encoded-array> + Definition: base address CCI I2C controller and length of memory + mapped region. + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: specifies the CCI I2C interrupt. The format of the + specifier is defined by the binding document describing + the node's interrupt parent. + +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: a list of phandle, should contain an entry for each + entries in clock-names. + +- clock-names + Usage: required + Value type: <string> + Definition: a list of clock names, must include "cci" clock. + +- power-domains + Usage: required for "qcom,msm-8996-cci" + Value type: <prop-encoded-array> + Definition: + +SUBNODES: + +The CCI provides I2C masters for one (msm8916) or two i2c busses (msm8996), +described as subdevices named "i2c-bus@0" and "i2c-bus@1". + +PROPERTIES: + +- reg: + Usage: required + Value type: <u32> + Definition: Index of the CCI bus/master + +- clock-frequency: + Usage: optional + Value type: <u32> + Definition: Desired I2C bus clock frequency in Hz, defaults to 100 + kHz if omitted. + +Example: + + cci@a0c000 { + compatible = "qcom,msm-8996-cci"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0xa0c000 0x1000>; + interrupts = <GIC_SPI 295 IRQ_TYPE_EDGE_RISING>; + clocks = <&mmcc MMSS_MMAGIC_AHB_CLK>, + <&mmcc CAMSS_TOP_AHB_CLK>, + <&mmcc CAMSS_CCI_AHB_CLK>, + <&mmcc CAMSS_CCI_CLK>, + <&mmcc CAMSS_AHB_CLK>; + clock-names = "mmss_mmagic_ahb", + "camss_top_ahb", + "cci_ahb", + "cci", + "camss_ahb"; + + i2c-bus@0 { + reg = <0>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c-bus@1 { + reg = <1>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi index 82e14cf08d8a..6147ae33ac4e 100644 --- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi +++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi @@ -496,6 +496,118 @@ status = "okay"; firmware-name = "qcom/msm8916/wcnss.mdt"; }; + + camera_vdddo_1v8: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "camera_vdddo"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + camera_vdda_2v8: fixedregulator@1 { + compatible = "regulator-fixed"; + regulator-name = "camera_vdda"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + }; + + camera_vddd_1v5: fixedregulator@2 { + compatible = "regulator-fixed"; + regulator-name = "camera_vddd"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + }; + + cci@1b0c000 { + status = "okay"; + i2c-bus@0 { + camera_rear@76 { + compatible = "ovti,ov5645"; + reg = <0x76>; + + enable-gpios = <&msmgpio 34 GPIO_ACTIVE_HIGH>; + reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&camera_rear_default>; + + clocks = <&gcc GCC_CAMSS_MCLK0_CLK>; + clock-names = "xclk"; + assigned-clocks = <&gcc GCC_CAMSS_MCLK0_CLK>; + assigned-clock-rates = <23880000>; + + vdddo-supply = <&camera_vdddo_1v8>; + vdda-supply = <&camera_vdda_2v8>; + vddd-supply = <&camera_vddd_1v5>; + + status = "disabled"; + + port { + ov5645_ep: endpoint { + clock-lanes = <1>; + data-lanes = <0 2>; + remote-endpoint = <&csiphy0_ep>; + }; + }; + }; + + camera_rear@74 { + compatible = "ovti,ov5645"; + reg = <0x74>; + + enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>; + reset-gpios = <&msmgpio 28 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&camera_front_default>; + + clocks = <&gcc GCC_CAMSS_MCLK1_CLK>; + clock-names = "xclk"; + assigned-clocks = <&gcc GCC_CAMSS_MCLK1_CLK>; + assigned-clock-rates = <23880000>; + + vdddo-supply = <&camera_vdddo_1v8>; + vdda-supply = <&camera_vdda_2v8>; + vddd-supply = <&camera_vddd_1v5>; + + status = "disabled"; + + port { + ov5645_2_ep: endpoint { + clock-lanes = <1>; + data-lanes = <0 2>; + remote-endpoint = <&csiphy1_ep>; + }; + }; + }; + }; + }; + + camss@1b00000 { + status = "ok"; + ports { + port@0 { + reg = <0>; + csiphy0_ep: endpoint { + clock-lanes = <1>; + data-lanes = <0 2>; + remote-endpoint = <&ov5645_ep>; + status = "disabled"; + }; + }; + + port@1 { + reg = <1>; + csiphy1_ep: endpoint { + clock-lanes = <1>; + data-lanes = <0 2>; + remote-endpoint = <&ov5645_2_ep>; + status = "disabled"; + }; + }; + }; + }; }; usb2513 { diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi index a4cc5efc2ed8..c530db092614 100644 --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi @@ -1522,6 +1522,33 @@ }; }; + cci@1b0c000 { + compatible = "qcom,msm8916-cci"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x1b0c000 0x1000>; + interrupts = <GIC_SPI 50 IRQ_TYPE_EDGE_RISING>; + clocks = <&gcc GCC_CAMSS_TOP_AHB_CLK>, + <&gcc GCC_CAMSS_CCI_AHB_CLK>, + <&gcc GCC_CAMSS_CCI_CLK>, + <&gcc GCC_CAMSS_AHB_CLK>; + clock-names = "camss_top_ahb", "cci_ahb", + "cci", "camss_ahb"; + assigned-clocks = <&gcc GCC_CAMSS_CCI_AHB_CLK>, + <&gcc GCC_CAMSS_CCI_CLK>; + assigned-clock-rates = <80000000>, <19200000>; + pinctrl-names = "default"; + pinctrl-0 = <&cci0_default>; + status = "disabled"; + + cci0: i2c-bus@0 { + reg = <0>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + camss: camss@1b00000 { compatible = "qcom,msm8916-camss"; reg = <0x1b0ac00 0x200>, diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig index ee37e0f417f5..e9f185470802 100644 --- a/arch/arm64/configs/defconfig +++ b/arch/arm64/configs/defconfig @@ -431,6 +431,7 @@ CONFIG_I2C_TEGRA=y CONFIG_I2C_UNIPHIER_F=y CONFIG_I2C_RCAR=y CONFIG_I2C_CROS_EC_TUNNEL=y +CONFIG_I2C_QCOM_CCI=y CONFIG_SPI=y CONFIG_SPI_ARMADA_3700=y CONFIG_SPI_BCM2835=m @@ -600,6 +601,7 @@ CONFIG_VIDEO_RENESAS_VSP1=m CONFIG_SDR_PLATFORM_DRIVERS=y CONFIG_VIDEO_RCAR_DRIF=m CONFIG_VIDEO_QCOM_VENUS=m +CONFIG_VIDEO_QCOM_CAMSS=m CONFIG_DRM=y CONFIG_DRM_I2C_NXP_TDA998X=m CONFIG_DRM_MALI_DISPLAY=m diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig index 2ddca08f8a76..b5d95af0f17a 100644 --- a/drivers/i2c/busses/Kconfig +++ b/drivers/i2c/busses/Kconfig @@ -898,6 +898,16 @@ config I2C_QCOM_GENI This driver can also be built as a module. If so, the module will be called i2c-qcom-geni. +config I2C_QCOM_CCI + tristate "Qualcomm Camera Control Interface" + depends on ARCH_QCOM || COMPILE_TEST + help + If you say yes to this option, support will be included for the + built-in camera control interface on the Qualcomm SoCs. + + This driver can also be built as a module. If so, the module + will be called i2c-qcom-cci. + config I2C_QUP tristate "Qualcomm QUP based I2C controller" depends on ARCH_QCOM diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile index 25d60889713c..e95454f97536 100644 --- a/drivers/i2c/busses/Makefile +++ b/drivers/i2c/busses/Makefile @@ -92,6 +92,7 @@ obj-$(CONFIG_I2C_PUV3) += i2c-puv3.o obj-$(CONFIG_I2C_PXA) += i2c-pxa.o obj-$(CONFIG_I2C_PXA_PCI) += i2c-pxa-pci.o obj-$(CONFIG_I2C_QCOM_GENI) += i2c-qcom-geni.o +obj-$(CONFIG_I2C_QCOM_CCI) += i2c-qcom-cci.o obj-$(CONFIG_I2C_QUP) += i2c-qup.o obj-$(CONFIG_I2C_RIIC) += i2c-riic.o obj-$(CONFIG_I2C_RK3X) += i2c-rk3x.o diff --git a/drivers/i2c/busses/i2c-qcom-cci.c b/drivers/i2c/busses/i2c-qcom-cci.c new file mode 100644 index 000000000000..2407b0187aad --- /dev/null +++ b/drivers/i2c/busses/i2c-qcom-cci.c @@ -0,0 +1,781 @@ +// SPDX-License-Identifier: GPL-2.0 +// Copyright (c) 2012-2016, The Linux Foundation. All rights reserved. +// Copyright (c) 2017-19 Linaro Limited. + +#include <linux/clk.h> +#include <linux/completion.h> +#include <linux/i2c.h> +#include <linux/io.h> +#include <linux/interrupt.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/pm_runtime.h> + +#define CCI_HW_VERSION 0x0 +#define CCI_RESET_CMD 0x004 +#define CCI_RESET_CMD_MASK 0x0f73f3f7 +#define CCI_RESET_CMD_M0_MASK 0x000003f1 +#define CCI_RESET_CMD_M1_MASK 0x0003f001 +#define CCI_QUEUE_START 0x008 +#define CCI_HALT_REQ 0x034 +#define CCI_HALT_REQ_I2C_M0_Q0Q1 BIT(0) +#define CCI_HALT_REQ_I2C_M1_Q0Q1 BIT(1) + +#define CCI_I2C_Mm_SCL_CTL(m) (0x100 + 0x100 * (m)) +#define CCI_I2C_Mm_SDA_CTL_0(m) (0x104 + 0x100 * (m)) +#define CCI_I2C_Mm_SDA_CTL_1(m) (0x108 + 0x100 * (m)) +#define CCI_I2C_Mm_SDA_CTL_2(m) (0x10c + 0x100 * (m)) +#define CCI_I2C_Mm_MISC_CTL(m) (0x110 + 0x100 * (m)) + +#define CCI_I2C_Mm_READ_DATA(m) (0x118 + 0x100 * (m)) +#define CCI_I2C_Mm_READ_BUF_LEVEL(m) (0x11c + 0x100 * (m)) +#define CCI_I2C_Mm_Qn_EXEC_WORD_CNT(m, n) (0x300 + 0x200 * (m) + 0x100 * (n)) +#define CCI_I2C_Mm_Qn_CUR_WORD_CNT(m, n) (0x304 + 0x200 * (m) + 0x100 * (n)) +#define CCI_I2C_Mm_Qn_CUR_CMD(m, n) (0x308 + 0x200 * (m) + 0x100 * (n)) +#define CCI_I2C_Mm_Qn_REPORT_STATUS(m, n) (0x30c + 0x200 * (m) + 0x100 * (n)) +#define CCI_I2C_Mm_Qn_LOAD_DATA(m, n) (0x310 + 0x200 * (m) + 0x100 * (n)) + +#define CCI_IRQ_GLOBAL_CLEAR_CMD 0xc00 +#define CCI_IRQ_MASK_0 0xc04 +#define CCI_IRQ_MASK_0_I2C_M0_RD_DONE BIT(0) +#define CCI_IRQ_MASK_0_I2C_M0_Q0_REPORT BIT(4) +#define CCI_IRQ_MASK_0_I2C_M0_Q1_REPORT BIT(8) +#define CCI_IRQ_MASK_0_I2C_M1_RD_DONE BIT(12) +#define CCI_IRQ_MASK_0_I2C_M1_Q0_REPORT BIT(16) +#define CCI_IRQ_MASK_0_I2C_M1_Q1_REPORT BIT(20) +#define CCI_IRQ_MASK_0_RST_DONE_ACK BIT(24) +#define CCI_IRQ_MASK_0_I2C_M0_Q0Q1_HALT_ACK BIT(25) +#define CCI_IRQ_MASK_0_I2C_M1_Q0Q1_HALT_ACK BIT(26) +#define CCI_IRQ_MASK_0_I2C_M0_ERROR 0x18000ee6 +#define CCI_IRQ_MASK_0_I2C_M1_ERROR 0x60ee6000 +#define CCI_IRQ_CLEAR_0 0xc08 +#define CCI_IRQ_STATUS_0 0xc0c +#define CCI_IRQ_STATUS_0_I2C_M0_RD_DONE BIT(0) +#define CCI_IRQ_STATUS_0_I2C_M0_Q0_REPORT BIT(4) +#define CCI_IRQ_STATUS_0_I2C_M0_Q1_REPORT BIT(8) +#define CCI_IRQ_STATUS_0_I2C_M1_RD_DONE BIT(12) +#define CCI_IRQ_STATUS_0_I2C_M1_Q0_REPORT BIT(16) +#define CCI_IRQ_STATUS_0_I2C_M1_Q1_REPORT BIT(20) +#define CCI_IRQ_STATUS_0_RST_DONE_ACK BIT(24) +#define CCI_IRQ_STATUS_0_I2C_M0_Q0Q1_HALT_ACK BIT(25) +#define CCI_IRQ_STATUS_0_I2C_M1_Q0Q1_HALT_ACK BIT(26) +#define CCI_IRQ_STATUS_0_I2C_M0_ERROR 0x18000ee6 +#define CCI_IRQ_STATUS_0_I2C_M1_ERROR 0x60ee6000 + +#define CCI_TIMEOUT (msecs_to_jiffies(100)) +#define NUM_MASTERS 2 +#define NUM_QUEUES 2 + +/* Max number of resources + 1 for a NULL terminator */ +#define CCI_RES_MAX 6 + + +#define CCI_I2C_SET_PARAM 1 +#define CCI_I2C_REPORT 8 +#define CCI_I2C_WRITE 9 +#define CCI_I2C_READ 10 + +#define CCI_I2C_REPORT_IRQ_EN BIT(8) + +enum { + I2C_MODE_STANDARD, + I2C_MODE_FAST, + I2C_MODE_FAST_PLUS, +}; + +enum cci_i2c_queue_t { + QUEUE_0, + QUEUE_1 +}; + +struct hw_params { + u16 thigh; /* HIGH period of the SCL clock in clock ticks */ + u16 tlow; /* LOW period of the SCL clock */ + u16 tsu_sto; /* set-up time for STOP condition */ + u16 tsu_sta; /* set-up time for a repeated START condition */ + u16 thd_dat; /* data hold time */ + u16 thd_sta; /* hold time (repeated) START condition */ + u16 tbuf; /* bus free time between a STOP and START condition */ + u8 scl_stretch_en; + u16 trdhld; + u16 tsp; /* pulse width of spikes suppressed by the input filter */ +}; + +struct cci; + +struct cci_master { + struct i2c_adapter adap; + u16 master; + u8 mode; + int status; + struct completion irq_complete; + struct cci *cci; +}; + +struct cci_data { + unsigned int num_masters; + struct i2c_adapter_quirks quirks; + u16 queue_size[NUM_QUEUES]; + unsigned long cci_clk_rate; + struct hw_params params[3]; +}; + +struct cci { + struct device *dev; + void __iomem *base; + unsigned int irq; + const struct cci_data *data; + struct clk_bulk_data *clocks; + int nclocks; + struct cci_master master[NUM_MASTERS]; +}; + +static irqreturn_t cci_isr(int irq, void *dev) +{ + struct cci *cci = dev; + u32 val, reset = 0; + int ret = IRQ_NONE; + + val = readl(cci->base + CCI_IRQ_STATUS_0); + writel(val, cci->base + CCI_IRQ_CLEAR_0); + writel(0x1, cci->base + CCI_IRQ_GLOBAL_CLEAR_CMD); + + if (val & CCI_IRQ_STATUS_0_RST_DONE_ACK) { + complete(&cci->master[0].irq_complete); + if (cci->master[1].master) + complete(&cci->master[1].irq_complete); + ret = IRQ_HANDLED; + } + + if (val & CCI_IRQ_STATUS_0_I2C_M0_RD_DONE || + val & CCI_IRQ_STATUS_0_I2C_M0_Q0_REPORT || + val & CCI_IRQ_STATUS_0_I2C_M0_Q1_REPORT) { + cci->master[0].status = 0; + complete(&cci->master[0].irq_complete); + ret = IRQ_HANDLED; + } + + if (val & CCI_IRQ_STATUS_0_I2C_M1_RD_DONE || + val & CCI_IRQ_STATUS_0_I2C_M1_Q0_REPORT || + val & CCI_IRQ_STATUS_0_I2C_M1_Q1_REPORT) { + cci->master[1].status = 0; + complete(&cci->master[1].irq_complete); + ret = IRQ_HANDLED; + } + + if (unlikely(val & CCI_IRQ_STATUS_0_I2C_M0_Q0Q1_HALT_ACK)) { + reset = CCI_RESET_CMD_M0_MASK; + ret = IRQ_HANDLED; + } + + if (unlikely(val & CCI_IRQ_STATUS_0_I2C_M1_Q0Q1_HALT_ACK)) { + reset = CCI_RESET_CMD_M1_MASK; + ret = IRQ_HANDLED; + } + + if (unlikely(reset)) + writel(reset, cci->base + CCI_RESET_CMD); + + if (unlikely(val & CCI_IRQ_STATUS_0_I2C_M0_ERROR)) { + dev_err_ratelimited(cci->dev, "Master 0 error 0x%08x\n", val); + cci->master[0].status = -EIO; + writel(CCI_HALT_REQ_I2C_M0_Q0Q1, cci->base + CCI_HALT_REQ); + ret = IRQ_HANDLED; + } + + if (unlikely(val & CCI_IRQ_STATUS_0_I2C_M1_ERROR)) { + dev_err_ratelimited(cci->dev, "Master 1 error 0x%08x\n", val); + cci->master[1].status = -EIO; + writel(CCI_HALT_REQ_I2C_M1_Q0Q1, cci->base + CCI_HALT_REQ); + ret = IRQ_HANDLED; + } + + return ret; +} + +static int cci_halt(struct cci *cci, u8 master_num) +{ + struct cci_master *master; + u32 val; + + if (master_num > 1) { + dev_err(cci->dev, "Unsupported master idx (%u)\n", master_num); + return -EINVAL; + } + + val = BIT(master_num); + master = &cci->master[master_num]; + + reinit_completion(&master->irq_complete); + writel(val, cci->base + CCI_HALT_REQ); + + if (!wait_for_completion_timeout(&master->irq_complete, CCI_TIMEOUT)) { + dev_err(cci->dev, "CCI halt timeout\n"); + return -ETIMEDOUT; + } + + return 0; +} + +static int cci_reset(struct cci *cci) +{ + /* + * we reset the whole controller, here and for implicity use + * master[0].xxx for waiting on it. + */ + reinit_completion(&cci->master[0].irq_complete); + writel(CCI_RESET_CMD_MASK, cci->base + CCI_RESET_CMD); + + if (!wait_for_completion_timeout(&cci->master[0].irq_complete, + CCI_TIMEOUT)) { + dev_err(cci->dev, "CCI reset timeout\n"); + return -ETIMEDOUT; + } + + return 0; +} + +static int cci_init(struct cci *cci, const struct hw_params *hw) +{ + u32 val = CCI_IRQ_MASK_0_I2C_M0_RD_DONE | + CCI_IRQ_MASK_0_I2C_M0_Q0_REPORT | + CCI_IRQ_MASK_0_I2C_M0_Q1_REPORT | + CCI_IRQ_MASK_0_I2C_M1_RD_DONE | + CCI_IRQ_MASK_0_I2C_M1_Q0_REPORT | + CCI_IRQ_MASK_0_I2C_M1_Q1_REPORT | + CCI_IRQ_MASK_0_RST_DONE_ACK | + CCI_IRQ_MASK_0_I2C_M0_Q0Q1_HALT_ACK | + CCI_IRQ_MASK_0_I2C_M1_Q0Q1_HALT_ACK | + CCI_IRQ_MASK_0_I2C_M0_ERROR | + CCI_IRQ_MASK_0_I2C_M1_ERROR; + int i; + + writel(val, cci->base + CCI_IRQ_MASK_0); + + for (i = 0; i < cci->data->num_masters; i++) { + val = hw->thigh << 16 | hw->tlow; + writel(val, cci->base + CCI_I2C_Mm_SCL_CTL(i)); + + val = hw->tsu_sto << 16 | hw->tsu_sta; + writel(val, cci->base + CCI_I2C_Mm_SDA_CTL_0(i)); + + val = hw->thd_dat << 16 | hw->thd_sta; + writel(val, cci->base + CCI_I2C_Mm_SDA_CTL_1(i)); + + val = hw->tbuf; + writel(val, cci->base + CCI_I2C_Mm_SDA_CTL_2(i)); + + val = hw->scl_stretch_en << 8 | hw->trdhld << 4 | hw->tsp; + writel(val, cci->base + CCI_I2C_Mm_MISC_CTL(i)); + } + + return 0; +} + +static int cci_run_queue(struct cci *cci, u8 master, u8 queue) +{ + u32 val; + int ret; + + val = readl(cci->base + CCI_I2C_Mm_Qn_CUR_WORD_CNT(master, queue)); + writel(val, cci->base + CCI_I2C_Mm_Qn_EXEC_WORD_CNT(master, queue)); + + reinit_completion(&cci->master[master].irq_complete); + val = BIT(master * 2 + queue); + writel(val, cci->base + CCI_QUEUE_START); + + if (!wait_for_completion_timeout(&cci->master[master].irq_complete, + CCI_TIMEOUT)) { + dev_err(cci->dev, "master %d queue %d timeout\n", + master, queue); + + cci_reset(cci); + cci_init(cci, &cci->data->params[cci->master[master].mode]); + return -ETIMEDOUT; + } + + ret = cci->master[master].status; + if (ret < 0) + dev_err(cci->dev, "master %d queue %d error %d\n", + master, queue, ret); + + return ret; +} + +static int cci_validate_queue(struct cci *cci, u8 master, u8 queue) +{ + u32 val; + + val = readl(cci->base + CCI_I2C_Mm_Qn_CUR_WORD_CNT(master, queue)); + if (val == cci->data->queue_size[queue]) + return -EINVAL; + + if (!val) + return 0; + + val = CCI_I2C_REPORT | CCI_I2C_REPORT_IRQ_EN; + writel(val, cci->base + CCI_I2C_Mm_Qn_LOAD_DATA(master, queue)); + + return cci_run_queue(cci, master, queue); +} + +static int cci_i2c_read(struct cci *cci, u16 master, + u16 addr, u8 *buf, u16 len) +{ + u32 val, words_read, words_exp; + u8 queue = QUEUE_1; + int i, index = 0, ret; + bool first = true; + + /* + * Call validate queue to make sure queue is empty before starting. + * This is to avoid overflow / underflow of queue. + */ + ret = cci_validate_queue(cci, master, queue); + if (ret < 0) + return ret; + + val = CCI_I2C_SET_PARAM | (addr & 0x7f) << 4; + writel(val, cci->base + CCI_I2C_Mm_Qn_LOAD_DATA(master, queue)); + + val = CCI_I2C_READ | len << 4; + writel(val, cci->base + CCI_I2C_Mm_Qn_LOAD_DATA(master, queue)); + + ret = cci_run_queue(cci, master, queue); + if (ret < 0) + return ret; + + words_read = readl(cci->base + CCI_I2C_Mm_READ_BUF_LEVEL(master)); + words_exp = len / 4 + 1; + if (words_read != words_exp) { + dev_err(cci->dev, "words read = %d, words expected = %d\n", + words_read, words_exp); + return -EIO; + } + + do { + val = readl(cci->base + CCI_I2C_Mm_READ_DATA(master)); + + for (i = 0; i < 4 && index < len; i++) { + if (first) { + first = false; + continue; + } + buf[index++] = (val >> (i * 8)) & 0xff; + } + } while (--words_read); + + return 0; +} + +static int cci_i2c_write(struct cci *cci, u16 master, + u16 addr, u8 *buf, u16 len) +{ + u8 queue = QUEUE_0; + u8 load[12] = { 0 }; + int i = 0, j, ret; + u32 val; + + /* + * Call validate queue to make sure queue is empty before starting. + * This is to avoid overflow / underflow of queue. + */ + ret = cci_validate_queue(cci, master, queue); + if (ret < 0) + return ret; + + val = CCI_I2C_SET_PARAM | (addr & 0x7f) << 4; + writel(val, cci->base + CCI_I2C_Mm_Qn_LOAD_DATA(master, queue)); + + load[i++] = CCI_I2C_WRITE | len << 4; + + for (j = 0; j < len; j++) + load[i++] = buf[j]; + + for (j = 0; j < i; j += 4) { + val = load[j]; + val |= load[j + 1] << 8; + val |= load[j + 2] << 16; + val |= load[j + 3] << 24; + writel(val, cci->base + CCI_I2C_Mm_Qn_LOAD_DATA(master, queue)); + } + + val = CCI_I2C_REPORT | CCI_I2C_REPORT_IRQ_EN; + writel(val, cci->base + CCI_I2C_Mm_Qn_LOAD_DATA(master, queue)); + + return cci_run_queue(cci, master, queue); +} + +static int cci_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num) +{ + struct cci_master *cci_master = i2c_get_adapdata(adap); + struct cci *cci = cci_master->cci; + int i, ret; + + ret = pm_runtime_get_sync(cci->dev); + if (ret < 0) + goto err; + + for (i = 0; i < num; i++) { + if (msgs[i].flags & I2C_M_RD) + ret = cci_i2c_read(cci, cci_master->master, + msgs[i].addr, msgs[i].buf, + msgs[i].len); + else + ret = cci_i2c_write(cci, cci_master->master, + msgs[i].addr, msgs[i].buf, + msgs[i].len); + + if (ret < 0) { + dev_err(cci->dev, "cci i2c xfer error %d", ret); + break; + } + } + + if (!ret) + ret = num; + +err: + pm_runtime_mark_last_busy(cci->dev); + pm_runtime_put_autosuspend(cci->dev); + + return ret; +} + +static u32 cci_func(struct i2c_adapter *adap) +{ + return I2C_FUNC_I2C; +} + +static const struct i2c_algorithm cci_algo = { + .master_xfer = cci_xfer, + .functionality = cci_func, +}; + +static int cci_enable_clocks(struct cci *cci) +{ + int ret; + + ret = clk_bulk_prepare_enable(cci->nclocks, cci->clocks); + if (ret < 0) + dev_err(cci->dev, "Bulk clock prepare failed: %d\n", ret); + + return ret; +} + +static void cci_disable_clocks(struct cci *cci) +{ + clk_bulk_disable_unprepare(cci->nclocks, cci->clocks); +} + +#ifdef CONFIG_PM +static int cci_suspend_runtime(struct device *dev) +{ + struct cci *cci = dev_get_drvdata(dev); + + dev_dbg(dev, "Supend invoked\n"); + cci_disable_clocks(cci); + return 0; +} + +static int cci_resume_runtime(struct device *dev) +{ + struct cci *cci = dev_get_drvdata(dev); + + dev_dbg(dev, "Resume invoked\n"); + return cci_enable_clocks(cci); +} +#endif + +#ifdef CONFIG_PM_SLEEP +static int cci_suspend(struct device *dev) +{ + if (!pm_runtime_suspended(dev)) + return cci_suspend_runtime(dev); + + return 0; +} + +static int cci_resume(struct device *dev) +{ + cci_resume_runtime(dev); + pm_runtime_mark_last_busy(dev); + pm_request_autosuspend(dev); + + return 0; +} +#endif + +static const struct dev_pm_ops qcom_cci_pm = { + SET_SYSTEM_SLEEP_PM_OPS(cci_suspend, cci_resume) + SET_RUNTIME_PM_OPS(cci_suspend_runtime, cci_resume_runtime, NULL) +}; + +static int cci_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct device_node *of_node = NULL; + unsigned long cci_clk_rate = 0; + struct resource *r; + struct cci *cci; + int ret = 0, i; + u32 val; + + cci = devm_kzalloc(dev, sizeof(*cci), GFP_KERNEL); + if (!cci) + return -ENOMEM; + + cci->dev = dev; + platform_set_drvdata(pdev, cci); + cci->data = device_get_match_data(&pdev->dev); + if (!cci->data) { + dev_err(&pdev->dev, "Driver data is null, abort\n"); + return -EIO; + } + + for (i = 0; i < cci->data->num_masters; i++) { + cci->master[i].adap.quirks = &cci->data->quirks; + cci->master[i].adap.algo = &cci_algo; + cci->master[i].adap.dev.parent = cci->dev; + cci->master[i].master = i; + cci->master[i].cci = cci; + + i2c_set_adapdata(&cci->master[i].adap, &cci->master[i]); + snprintf(cci->master[i].adap.name, + sizeof(cci->master[i].adap.name), + "Qualcomm Camera Control Interface: %d", i); + + /* find the child node for i2c-bus as we are on cci node */ + of_node = of_get_next_available_child(dev->of_node, of_node); + if (!of_node) { + dev_err(dev, "Missing i2c-bus@%d child node\n", i); + return -EINVAL; + } + cci->master[i].adap.dev.of_node = of_node; + + cci->master[i].mode = I2C_MODE_STANDARD; + ret = of_property_read_u32(of_node, "clock-frequency", &val); + if (!ret) { + if (val == 400000) + cci->master[i].mode = I2C_MODE_FAST; + else if (val == 1000000) + cci->master[i].mode = I2C_MODE_FAST_PLUS; + } + + init_completion(&cci->master[i].irq_complete); + } + + /* Memory */ + + r = platform_get_resource(pdev, IORESOURCE_MEM, 0); + cci->base = devm_ioremap_resource(dev, r); + if (IS_ERR(cci->base)) + return PTR_ERR(cci->base); + + /* Interrupt */ + + ret = platform_get_irq(pdev, 0); + if (ret < 0) { + dev_err(dev, "missing IRQ: %d\n", ret); + return ret; + } + cci->irq = ret; + + ret = devm_request_irq(dev, cci->irq, cci_isr, + IRQF_TRIGGER_RISING, dev_name(dev), cci); + if (ret < 0) { + dev_err(dev, "request_irq failed, ret: %d\n", ret); + return ret; + } + + disable_irq(cci->irq); + + /* Clocks */ + + ret = devm_clk_bulk_get_all(dev, &cci->clocks); + if (ret < 1) { + dev_err(dev, "failed to get clocks %d\n", ret); + return ret; + } + cci->nclocks = ret; + + /* Retrieve CCI clock rate */ + for (i = 0; i < cci->nclocks; i++) { + if (!strncmp(cci->clocks[i].id, "cci", 4)) { + cci_clk_rate = clk_get_rate(cci->clocks[i].clk); + break; + } + } + + if (cci_clk_rate != cci->data->cci_clk_rate) { + /* cci clock set by the bootloader or via assigned clock rate + * in DT. + */ + dev_warn(dev, "Found %lu cci clk rate while %lu was expected\n", + cci_clk_rate, cci->data->cci_clk_rate); + } + + ret = cci_enable_clocks(cci); + if (ret < 0) + return ret; + + pm_runtime_set_autosuspend_delay(dev, MSEC_PER_SEC); + pm_runtime_use_autosuspend(dev); + pm_runtime_set_active(dev); + pm_runtime_enable(dev); + + val = readl_relaxed(cci->base + CCI_HW_VERSION); + dev_dbg(dev, "%s: CCI HW version = 0x%08x", __func__, val); + + enable_irq(cci->irq); + + ret = cci_reset(cci); + if (ret < 0) + goto error; + + for (i = 0; i < cci->data->num_masters; i++) { + ret = cci_init(cci, &cci->data->params[cci->master[i].mode]); + if (ret < 0) + goto pm_error; + + ret = i2c_add_adapter(&cci->master[i].adap); + if (ret < 0) + goto error_i2c; + } + + return 0; + +error_i2c: + for (; i >= 0; i--) + i2c_del_adapter(&cci->master[i].adap); +pm_error: + pm_runtime_disable(dev); + pm_runtime_set_suspended(dev); +error: + disable_irq(cci->irq); + cci_disable_clocks(cci); + + return ret; +} + +static int cci_remove(struct platform_device *pdev) +{ + struct cci *cci = platform_get_drvdata(pdev); + int i; + + for (i = 0; i < cci->data->num_masters; i++) { + i2c_del_adapter(&cci->master[i].adap); + cci_halt(cci, i); + } + + disable_irq(cci->irq); + pm_runtime_disable(&pdev->dev); + pm_runtime_set_suspended(&pdev->dev); + + return 0; +} + +static const struct cci_data cci_8916_data = { + .num_masters = 1, + .queue_size = { 64, 16 }, + .quirks = { + .max_write_len = 10, + .max_read_len = 12, + }, + .cci_clk_rate = 19200000, + .params[I2C_MODE_STANDARD] = { + .thigh = 78, + .tlow = 114, + .tsu_sto = 28, + .tsu_sta = 28, + .thd_dat = 10, + .thd_sta = 77, + .tbuf = 118, + .scl_stretch_en = 0, + .trdhld = 6, + .tsp = 1 + }, + .params[I2C_MODE_FAST] = { + .thigh = 20, + .tlow = 28, + .tsu_sto = 21, + .tsu_sta = 21, + .thd_dat = 13, + .thd_sta = 18, + .tbuf = 32, + .scl_stretch_en = 0, + .trdhld = 6, + .tsp = 3 + }, +}; + +static const struct cci_data cci_8996_data = { + .num_masters = 2, + .queue_size = { 64, 16 }, + .quirks = { + .max_write_len = 11, + .max_read_len = 12, + }, + .cci_clk_rate = 37500000, + .params[I2C_MODE_STANDARD] = { + .thigh = 201, + .tlow = 174, + .tsu_sto = 204, + .tsu_sta = 231, + .thd_dat = 22, + .thd_sta = 162, + .tbuf = 227, + .scl_stretch_en = 0, + .trdhld = 6, + .tsp = 3 + }, + .params[I2C_MODE_FAST] = { + .thigh = 38, + .tlow = 56, + .tsu_sto = 40, + .tsu_sta = 40, + .thd_dat = 22, + .thd_sta = 35, + .tbuf = 62, + .scl_stretch_en = 0, + .trdhld = 6, + .tsp = 3 + }, + .params[I2C_MODE_FAST_PLUS] = { + .thigh = 16, + .tlow = 22, + .tsu_sto = 17, + .tsu_sta = 18, + .thd_dat = 16, + .thd_sta = 15, + .tbuf = 24, + .scl_stretch_en = 0, + .trdhld = 3, + .tsp = 3 + }, +}; + +static const struct of_device_id cci_dt_match[] = { + { .compatible = "qcom,msm8916-cci", .data = &cci_8916_data}, + { .compatible = "qcom,msm8996-cci", .data = &cci_8996_data}, + {} +}; +MODULE_DEVICE_TABLE(of, cci_dt_match); + +static struct platform_driver qcom_cci_driver = { + .probe = cci_probe, + .remove = cci_remove, + .driver = { + .name = "i2c-qcom-cci", + .of_match_table = cci_dt_match, + .pm = &qcom_cci_pm, + }, +}; + +module_platform_driver(qcom_cci_driver); + +MODULE_DESCRIPTION("Qualcomm Camera Control Interface driver"); +MODULE_AUTHOR("Todor Tomov <todor.tomov@linaro.org>"); +MODULE_AUTHOR("Loic Poulain <loic.poulain@linaro.org>"); +MODULE_LICENSE("GPL v2"); |