diff options
Diffstat (limited to 'README')
| -rw-r--r-- | README | 51 |
1 files changed, 50 insertions, 1 deletions
@@ -432,6 +432,14 @@ The following options need to be configured: Select high exception vectors of the ARM core, e.g., do not clear the V bit of the c1 register of CP15. + CONFIG_SYS_THUMB_BUILD + + Use this flag to build U-Boot using the Thumb instruction + set for ARM architectures. Thumb instruction set provides + better code density. For ARM architectures that support + Thumb2 this flag will result in Thumb2 code generated by + GCC. + - Linux Kernel Interface: CONFIG_CLOCKS_IN_MHZ @@ -777,6 +785,8 @@ The following options need to be configured: CONFIG_CMD_JFFS2 * JFFS2 Support CONFIG_CMD_KGDB * kgdb CONFIG_CMD_LDRINFO ldrinfo (display Blackfin loader) + CONFIG_CMD_LINK_LOCAL * link-local IP address auto-configuration + (169.254.*.*) CONFIG_CMD_LOADB loadb CONFIG_CMD_LOADS loads CONFIG_CMD_MD5SUM print md5 message digest @@ -814,7 +824,7 @@ The following options need to be configured: CONFIG_CMD_TIME * run command and report execution time CONFIG_CMD_USB * USB support CONFIG_CMD_CDP * Cisco Discover Protocol support - CONFIG_CMD_FSL * Microblaze FSL support + CONFIG_CMD_MFSL * Microblaze FSL support EXAMPLE: If you want all functions except of network @@ -1584,10 +1594,17 @@ The following options need to be configured: CONFIG_BOOTP_NTPSERVER CONFIG_BOOTP_TIMEOFFSET CONFIG_BOOTP_VENDOREX + CONFIG_BOOTP_MAY_FAIL CONFIG_BOOTP_SERVERIP - TFTP server will be the serverip environment variable, not the BOOTP server. + CONFIG_BOOTP_MAY_FAIL - If the DHCP server is not found + after the configured retry count, the call will fail + instead of starting over. This can be used to fail over + to Link-local IP address configuration if the DHCP server + is not available. + CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS serverip from a DHCP server, it is possible that more than one DNS serverip is offered to the client. @@ -1618,6 +1635,14 @@ The following options need to be configured: the DHCP timeout and retry process takes a longer than this delay. + - Link-local IP address negotiation: + Negotiate with other link-local clients on the local network + for an address that doesn't require explicit configuration. + This is especially useful if a DHCP server cannot be guaranteed + to exist in all environments that the device must operate. + + See doc/README.link-local for more information. + - CDP Options: CONFIG_CDP_DEVICE_ID @@ -3026,6 +3051,24 @@ to save the current settings. environment area within the total memory of your DataFlash placed at the specified address. +- CONFIG_ENV_IS_IN_REMOTE: + + Define this if you have a remote memory space which you + want to use for the local device's environment. + + - CONFIG_ENV_ADDR: + - CONFIG_ENV_SIZE: + + These two #defines specify the address and size of the + environment area within the remote memory space. The + local device can get the environment from remote memory + space by SRIO or other links. + +BE CAREFUL! For some special cases, the local device can not use +"saveenv" command. For example, the local device will get the +environment stored in a remote NOR flash by SRIO link, but it can +not erase, write this NOR flash by SRIO interface. + - CONFIG_ENV_IS_IN_NAND: Define this if you have a NAND device which you want to use @@ -3462,6 +3505,12 @@ within that device. Specifies that QE/FMAN firmware is located on the primary SPI device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device. +- CONFIG_SYS_QE_FMAN_FW_IN_REMOTE + Specifies that QE/FMAN firmware is located in the remote (master) + memory space. CONFIG_SYS_FMAN_FW_ADDR is a virtual address which + can be mapped from slave TLB->slave LAW->slave SRIO outbound window + ->master inbound window->master LAW->the ucode address in master's + NOR flash. Building the Software: ====================== |