Android: Linux: serial console test case unification

Change-Id: If1825f91667468fe09980ac201590790c449a753
Signed-off-by: Milosz Wasilewski <milosz.wasilewski@linaro.org>

3 files changed, 41 insertions, 76 deletions

diff --git a/generic/android/serial-console.yaml b/generic/android/serial-console.yaml
deleted file mode 100644
index 97ea267..0000000
--- a/generic/android/serial-console.yaml
+++ /dev/null
@@ -1,39 +0,0 @@
-metadata:
-    name: andriod-serial-console
-    format: "Manual Test Definition 1.0"
-    description: "Test if the serial connection to the board works well"
-    maintainer:
-        - amit.khare@linaro.org
-    os:
-        - android
-    scope:
-        - functional
-    devices:
-        - panda
-        - panda-es
-        - vexpress-a9
-        - vexpress-tc2
-        - arndale
-        - hikey
-    environment:
-        - manual-test
-
-run:
-    steps:
-        - Connect the serial cable.
-        - Install minicom on host PC.
-        - "$ sudo apt-get install minicom"
-        - Launch minicom run "$ sudo minicom -s"
-        - Set data transfer speed to "115200 8N1". For ARM Versatile Express board, it is "38400 8N1"
-        - Save and exit minicom.
-        - Re-launch minicom and run "$sudo minicom"
-        - Power on and boot the board under test.
-        - For Hikey board, If the 4 pin jumper block for UART0 is installed, attach a serial terminal and
-          ensure the console is displayed on the serial terminal. If a mezzanine board is available for UART1,
-          install it, attach a serial terminal and ensure the console is displayed on the serial terminal.
-
-
-    expected:
-        - "Verify that the output looks good."
-        - "Verify that you can type in serial console."
-
diff --git a/generic/linux/serial-console.yaml b/generic/linux/serial-console.yaml
deleted file mode 100644
index cf90059..0000000
--- a/generic/linux/serial-console.yaml
+++ /dev/null
@@ -1,37 +0,0 @@
-metadata:
-    name: serial-console
-    format: "Manual Test Definition 1.0"
-    description: "Test if the serial connection to the board works"
-    maintainer:
-        - amit.khare@linaro.org
-    os:
-        - ubuntu
-        - openembedded
-    scope:
-        - functional
-    devices:
-        - panda
-        - panda-es
-        - vexpress-a9
-        - vexpress-tc2
-        - arndale
-        - ifc6410
-        - hikey
-    environment:
-        - manual-test
-
-run:
-    steps:
-        - Connect the Serial Cable.
-        - Launch minicom in terminal of host PC.
-        - "$ minicom -D /dev/ttyUSB0 -w -C minicom_log.txt"
-        - "$ sudo screen /dev/ttyUSB0 115200"
-        - Boot the board.
-        - After boot sequence is complete run
-        - "$ ls -l"
-
-    expected:
-        - "Boot log should be shown in serial console after powering the board"
-        - "The boot log and command line prompt at the end should look like this: root@linaro-developer:~#"
-        - "Input by keyboard in serial console should work and characters should be echoed back and displayed in minicom"
-
diff --git a/generic/serial-console.yaml b/generic/serial-console.yaml
new file mode 100644
index 0000000..7b1f29b
--- /dev/null
+++ b/generic/serial-console.yaml
@@ -0,0 +1,41 @@
+metadata:
+    name: serial-console
+    format: "Manual Test Definition 1.0"
+    description: "Test if the serial connection to the board works"
+    maintainer:
+        - amit.khare@linaro.org
+    os:
+        - android
+        - ubuntu
+        - openembedded
+    scope:
+        - functional
+    devices:
+        - panda
+        - panda-es
+        - vexpress-a9
+        - vexpress-tc2
+        - juno
+        - arndale
+        - ifc6410
+        - hi6220-hikey
+        - apq8016-sbc
+    environment:
+        - manual-test
+
+run:
+    steps:
+        # depending on the board, the serial cable might be UART or symmetric serial
+        - Connect the serial cable to the device under test
+        - Launch minicom in terminal of host PC.
+        # correct tty should be used. /dev/ttyUSB0 is just an example
+        - "$ minicom -D /dev/ttyUSB0 -w -C minicom_log.txt"
+        - Power the device under test
+        - After boot sequence is complete run the following command in the console
+        - "$ ls -l"
+
+    expected:
+        - Boot log is displayed in minicom after powering the device under test
+        - Command line prompt is displayed after successful boot.
+        - Input by keyboard in works and characters are echoed back and displayed in minicom
+