aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/intel/e1000e/mac.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/ethernet/intel/e1000e/mac.c')
-rw-r--r--drivers/net/ethernet/intel/e1000e/mac.c1709
1 files changed, 1709 insertions, 0 deletions
diff --git a/drivers/net/ethernet/intel/e1000e/mac.c b/drivers/net/ethernet/intel/e1000e/mac.c
new file mode 100644
index 00000000000..decad98c105
--- /dev/null
+++ b/drivers/net/ethernet/intel/e1000e/mac.c
@@ -0,0 +1,1709 @@
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2012 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+#include "e1000.h"
+
+/**
+ * e1000e_get_bus_info_pcie - Get PCIe bus information
+ * @hw: pointer to the HW structure
+ *
+ * Determines and stores the system bus information for a particular
+ * network interface. The following bus information is determined and stored:
+ * bus speed, bus width, type (PCIe), and PCIe function.
+ **/
+s32 e1000e_get_bus_info_pcie(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ struct e1000_bus_info *bus = &hw->bus;
+ struct e1000_adapter *adapter = hw->adapter;
+ u16 pcie_link_status, cap_offset;
+
+ cap_offset = adapter->pdev->pcie_cap;
+ if (!cap_offset) {
+ bus->width = e1000_bus_width_unknown;
+ } else {
+ pci_read_config_word(adapter->pdev,
+ cap_offset + PCIE_LINK_STATUS,
+ &pcie_link_status);
+ bus->width = (enum e1000_bus_width)((pcie_link_status &
+ PCIE_LINK_WIDTH_MASK) >>
+ PCIE_LINK_WIDTH_SHIFT);
+ }
+
+ mac->ops.set_lan_id(hw);
+
+ return 0;
+}
+
+/**
+ * e1000_set_lan_id_multi_port_pcie - Set LAN id for PCIe multiple port devices
+ *
+ * @hw: pointer to the HW structure
+ *
+ * Determines the LAN function id by reading memory-mapped registers
+ * and swaps the port value if requested.
+ **/
+void e1000_set_lan_id_multi_port_pcie(struct e1000_hw *hw)
+{
+ struct e1000_bus_info *bus = &hw->bus;
+ u32 reg;
+
+ /*
+ * The status register reports the correct function number
+ * for the device regardless of function swap state.
+ */
+ reg = er32(STATUS);
+ bus->func = (reg & E1000_STATUS_FUNC_MASK) >> E1000_STATUS_FUNC_SHIFT;
+}
+
+/**
+ * e1000_set_lan_id_single_port - Set LAN id for a single port device
+ * @hw: pointer to the HW structure
+ *
+ * Sets the LAN function id to zero for a single port device.
+ **/
+void e1000_set_lan_id_single_port(struct e1000_hw *hw)
+{
+ struct e1000_bus_info *bus = &hw->bus;
+
+ bus->func = 0;
+}
+
+/**
+ * e1000_clear_vfta_generic - Clear VLAN filter table
+ * @hw: pointer to the HW structure
+ *
+ * Clears the register array which contains the VLAN filter table by
+ * setting all the values to 0.
+ **/
+void e1000_clear_vfta_generic(struct e1000_hw *hw)
+{
+ u32 offset;
+
+ for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) {
+ E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset, 0);
+ e1e_flush();
+ }
+}
+
+/**
+ * e1000_write_vfta_generic - Write value to VLAN filter table
+ * @hw: pointer to the HW structure
+ * @offset: register offset in VLAN filter table
+ * @value: register value written to VLAN filter table
+ *
+ * Writes value at the given offset in the register array which stores
+ * the VLAN filter table.
+ **/
+void e1000_write_vfta_generic(struct e1000_hw *hw, u32 offset, u32 value)
+{
+ E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset, value);
+ e1e_flush();
+}
+
+/**
+ * e1000e_init_rx_addrs - Initialize receive address's
+ * @hw: pointer to the HW structure
+ * @rar_count: receive address registers
+ *
+ * Setup the receive address registers by setting the base receive address
+ * register to the devices MAC address and clearing all the other receive
+ * address registers to 0.
+ **/
+void e1000e_init_rx_addrs(struct e1000_hw *hw, u16 rar_count)
+{
+ u32 i;
+ u8 mac_addr[ETH_ALEN] = { 0 };
+
+ /* Setup the receive address */
+ e_dbg("Programming MAC Address into RAR[0]\n");
+
+ e1000e_rar_set(hw, hw->mac.addr, 0);
+
+ /* Zero out the other (rar_entry_count - 1) receive addresses */
+ e_dbg("Clearing RAR[1-%u]\n", rar_count - 1);
+ for (i = 1; i < rar_count; i++)
+ e1000e_rar_set(hw, mac_addr, i);
+}
+
+/**
+ * e1000_check_alt_mac_addr_generic - Check for alternate MAC addr
+ * @hw: pointer to the HW structure
+ *
+ * Checks the nvm for an alternate MAC address. An alternate MAC address
+ * can be setup by pre-boot software and must be treated like a permanent
+ * address and must override the actual permanent MAC address. If an
+ * alternate MAC address is found it is programmed into RAR0, replacing
+ * the permanent address that was installed into RAR0 by the Si on reset.
+ * This function will return SUCCESS unless it encounters an error while
+ * reading the EEPROM.
+ **/
+s32 e1000_check_alt_mac_addr_generic(struct e1000_hw *hw)
+{
+ u32 i;
+ s32 ret_val = 0;
+ u16 offset, nvm_alt_mac_addr_offset, nvm_data;
+ u8 alt_mac_addr[ETH_ALEN];
+
+ ret_val = e1000_read_nvm(hw, NVM_COMPAT, 1, &nvm_data);
+ if (ret_val)
+ return ret_val;
+
+ /* not supported on 82573 */
+ if (hw->mac.type == e1000_82573)
+ return 0;
+
+ ret_val = e1000_read_nvm(hw, NVM_ALT_MAC_ADDR_PTR, 1,
+ &nvm_alt_mac_addr_offset);
+ if (ret_val) {
+ e_dbg("NVM Read Error\n");
+ return ret_val;
+ }
+
+ if ((nvm_alt_mac_addr_offset == 0xFFFF) ||
+ (nvm_alt_mac_addr_offset == 0x0000))
+ /* There is no Alternate MAC Address */
+ return 0;
+
+ if (hw->bus.func == E1000_FUNC_1)
+ nvm_alt_mac_addr_offset += E1000_ALT_MAC_ADDRESS_OFFSET_LAN1;
+ for (i = 0; i < ETH_ALEN; i += 2) {
+ offset = nvm_alt_mac_addr_offset + (i >> 1);
+ ret_val = e1000_read_nvm(hw, offset, 1, &nvm_data);
+ if (ret_val) {
+ e_dbg("NVM Read Error\n");
+ return ret_val;
+ }
+
+ alt_mac_addr[i] = (u8)(nvm_data & 0xFF);
+ alt_mac_addr[i + 1] = (u8)(nvm_data >> 8);
+ }
+
+ /* if multicast bit is set, the alternate address will not be used */
+ if (is_multicast_ether_addr(alt_mac_addr)) {
+ e_dbg("Ignoring Alternate Mac Address with MC bit set\n");
+ return 0;
+ }
+
+ /*
+ * We have a valid alternate MAC address, and we want to treat it the
+ * same as the normal permanent MAC address stored by the HW into the
+ * RAR. Do this by mapping this address into RAR0.
+ */
+ e1000e_rar_set(hw, alt_mac_addr, 0);
+
+ return 0;
+}
+
+/**
+ * e1000e_rar_set - Set receive address register
+ * @hw: pointer to the HW structure
+ * @addr: pointer to the receive address
+ * @index: receive address array register
+ *
+ * Sets the receive address array register at index to the address passed
+ * in by addr.
+ **/
+void e1000e_rar_set(struct e1000_hw *hw, u8 *addr, u32 index)
+{
+ u32 rar_low, rar_high;
+
+ /*
+ * HW expects these in little endian so we reverse the byte order
+ * from network order (big endian) to little endian
+ */
+ rar_low = ((u32)addr[0] | ((u32)addr[1] << 8) |
+ ((u32)addr[2] << 16) | ((u32)addr[3] << 24));
+
+ rar_high = ((u32)addr[4] | ((u32)addr[5] << 8));
+
+ /* If MAC address zero, no need to set the AV bit */
+ if (rar_low || rar_high)
+ rar_high |= E1000_RAH_AV;
+
+ /*
+ * Some bridges will combine consecutive 32-bit writes into
+ * a single burst write, which will malfunction on some parts.
+ * The flushes avoid this.
+ */
+ ew32(RAL(index), rar_low);
+ e1e_flush();
+ ew32(RAH(index), rar_high);
+ e1e_flush();
+}
+
+/**
+ * e1000_hash_mc_addr - Generate a multicast hash value
+ * @hw: pointer to the HW structure
+ * @mc_addr: pointer to a multicast address
+ *
+ * Generates a multicast address hash value which is used to determine
+ * the multicast filter table array address and new table value.
+ **/
+static u32 e1000_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr)
+{
+ u32 hash_value, hash_mask;
+ u8 bit_shift = 0;
+
+ /* Register count multiplied by bits per register */
+ hash_mask = (hw->mac.mta_reg_count * 32) - 1;
+
+ /*
+ * For a mc_filter_type of 0, bit_shift is the number of left-shifts
+ * where 0xFF would still fall within the hash mask.
+ */
+ while (hash_mask >> bit_shift != 0xFF)
+ bit_shift++;
+
+ /*
+ * The portion of the address that is used for the hash table
+ * is determined by the mc_filter_type setting.
+ * The algorithm is such that there is a total of 8 bits of shifting.
+ * The bit_shift for a mc_filter_type of 0 represents the number of
+ * left-shifts where the MSB of mc_addr[5] would still fall within
+ * the hash_mask. Case 0 does this exactly. Since there are a total
+ * of 8 bits of shifting, then mc_addr[4] will shift right the
+ * remaining number of bits. Thus 8 - bit_shift. The rest of the
+ * cases are a variation of this algorithm...essentially raising the
+ * number of bits to shift mc_addr[5] left, while still keeping the
+ * 8-bit shifting total.
+ *
+ * For example, given the following Destination MAC Address and an
+ * mta register count of 128 (thus a 4096-bit vector and 0xFFF mask),
+ * we can see that the bit_shift for case 0 is 4. These are the hash
+ * values resulting from each mc_filter_type...
+ * [0] [1] [2] [3] [4] [5]
+ * 01 AA 00 12 34 56
+ * LSB MSB
+ *
+ * case 0: hash_value = ((0x34 >> 4) | (0x56 << 4)) & 0xFFF = 0x563
+ * case 1: hash_value = ((0x34 >> 3) | (0x56 << 5)) & 0xFFF = 0xAC6
+ * case 2: hash_value = ((0x34 >> 2) | (0x56 << 6)) & 0xFFF = 0x163
+ * case 3: hash_value = ((0x34 >> 0) | (0x56 << 8)) & 0xFFF = 0x634
+ */
+ switch (hw->mac.mc_filter_type) {
+ default:
+ case 0:
+ break;
+ case 1:
+ bit_shift += 1;
+ break;
+ case 2:
+ bit_shift += 2;
+ break;
+ case 3:
+ bit_shift += 4;
+ break;
+ }
+
+ hash_value = hash_mask & (((mc_addr[4] >> (8 - bit_shift)) |
+ (((u16)mc_addr[5]) << bit_shift)));
+
+ return hash_value;
+}
+
+/**
+ * e1000e_update_mc_addr_list_generic - Update Multicast addresses
+ * @hw: pointer to the HW structure
+ * @mc_addr_list: array of multicast addresses to program
+ * @mc_addr_count: number of multicast addresses to program
+ *
+ * Updates entire Multicast Table Array.
+ * The caller must have a packed mc_addr_list of multicast addresses.
+ **/
+void e1000e_update_mc_addr_list_generic(struct e1000_hw *hw,
+ u8 *mc_addr_list, u32 mc_addr_count)
+{
+ u32 hash_value, hash_bit, hash_reg;
+ int i;
+
+ /* clear mta_shadow */
+ memset(&hw->mac.mta_shadow, 0, sizeof(hw->mac.mta_shadow));
+
+ /* update mta_shadow from mc_addr_list */
+ for (i = 0; (u32)i < mc_addr_count; i++) {
+ hash_value = e1000_hash_mc_addr(hw, mc_addr_list);
+
+ hash_reg = (hash_value >> 5) & (hw->mac.mta_reg_count - 1);
+ hash_bit = hash_value & 0x1F;
+
+ hw->mac.mta_shadow[hash_reg] |= (1 << hash_bit);
+ mc_addr_list += (ETH_ALEN);
+ }
+
+ /* replace the entire MTA table */
+ for (i = hw->mac.mta_reg_count - 1; i >= 0; i--)
+ E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, hw->mac.mta_shadow[i]);
+ e1e_flush();
+}
+
+/**
+ * e1000e_clear_hw_cntrs_base - Clear base hardware counters
+ * @hw: pointer to the HW structure
+ *
+ * Clears the base hardware counters by reading the counter registers.
+ **/
+void e1000e_clear_hw_cntrs_base(struct e1000_hw *hw)
+{
+ er32(CRCERRS);
+ er32(SYMERRS);
+ er32(MPC);
+ er32(SCC);
+ er32(ECOL);
+ er32(MCC);
+ er32(LATECOL);
+ er32(COLC);
+ er32(DC);
+ er32(SEC);
+ er32(RLEC);
+ er32(XONRXC);
+ er32(XONTXC);
+ er32(XOFFRXC);
+ er32(XOFFTXC);
+ er32(FCRUC);
+ er32(GPRC);
+ er32(BPRC);
+ er32(MPRC);
+ er32(GPTC);
+ er32(GORCL);
+ er32(GORCH);
+ er32(GOTCL);
+ er32(GOTCH);
+ er32(RNBC);
+ er32(RUC);
+ er32(RFC);
+ er32(ROC);
+ er32(RJC);
+ er32(TORL);
+ er32(TORH);
+ er32(TOTL);
+ er32(TOTH);
+ er32(TPR);
+ er32(TPT);
+ er32(MPTC);
+ er32(BPTC);
+}
+
+/**
+ * e1000e_check_for_copper_link - Check for link (Copper)
+ * @hw: pointer to the HW structure
+ *
+ * Checks to see of the link status of the hardware has changed. If a
+ * change in link status has been detected, then we read the PHY registers
+ * to get the current speed/duplex if link exists.
+ **/
+s32 e1000e_check_for_copper_link(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ s32 ret_val;
+ bool link;
+
+ /*
+ * We only want to go out to the PHY registers to see if Auto-Neg
+ * has completed and/or if our link status has changed. The
+ * get_link_status flag is set upon receiving a Link Status
+ * Change or Rx Sequence Error interrupt.
+ */
+ if (!mac->get_link_status)
+ return 0;
+
+ /*
+ * First we want to see if the MII Status Register reports
+ * link. If so, then we want to get the current speed/duplex
+ * of the PHY.
+ */
+ ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link);
+ if (ret_val)
+ return ret_val;
+
+ if (!link)
+ return 0; /* No link detected */
+
+ mac->get_link_status = false;
+
+ /*
+ * Check if there was DownShift, must be checked
+ * immediately after link-up
+ */
+ e1000e_check_downshift(hw);
+
+ /*
+ * If we are forcing speed/duplex, then we simply return since
+ * we have already determined whether we have link or not.
+ */
+ if (!mac->autoneg)
+ return -E1000_ERR_CONFIG;
+
+ /*
+ * Auto-Neg is enabled. Auto Speed Detection takes care
+ * of MAC speed/duplex configuration. So we only need to
+ * configure Collision Distance in the MAC.
+ */
+ mac->ops.config_collision_dist(hw);
+
+ /*
+ * Configure Flow Control now that Auto-Neg has completed.
+ * First, we need to restore the desired flow control
+ * settings because we may have had to re-autoneg with a
+ * different link partner.
+ */
+ ret_val = e1000e_config_fc_after_link_up(hw);
+ if (ret_val)
+ e_dbg("Error configuring flow control\n");
+
+ return ret_val;
+}
+
+/**
+ * e1000e_check_for_fiber_link - Check for link (Fiber)
+ * @hw: pointer to the HW structure
+ *
+ * Checks for link up on the hardware. If link is not up and we have
+ * a signal, then we need to force link up.
+ **/
+s32 e1000e_check_for_fiber_link(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ u32 rxcw;
+ u32 ctrl;
+ u32 status;
+ s32 ret_val;
+
+ ctrl = er32(CTRL);
+ status = er32(STATUS);
+ rxcw = er32(RXCW);
+
+ /*
+ * If we don't have link (auto-negotiation failed or link partner
+ * cannot auto-negotiate), the cable is plugged in (we have signal),
+ * and our link partner is not trying to auto-negotiate with us (we
+ * are receiving idles or data), we need to force link up. We also
+ * need to give auto-negotiation time to complete, in case the cable
+ * was just plugged in. The autoneg_failed flag does this.
+ */
+ /* (ctrl & E1000_CTRL_SWDPIN1) == 1 == have signal */
+ if ((ctrl & E1000_CTRL_SWDPIN1) && !(status & E1000_STATUS_LU) &&
+ !(rxcw & E1000_RXCW_C)) {
+ if (!mac->autoneg_failed) {
+ mac->autoneg_failed = true;
+ return 0;
+ }
+ e_dbg("NOT Rx'ing /C/, disable AutoNeg and force link.\n");
+
+ /* Disable auto-negotiation in the TXCW register */
+ ew32(TXCW, (mac->txcw & ~E1000_TXCW_ANE));
+
+ /* Force link-up and also force full-duplex. */
+ ctrl = er32(CTRL);
+ ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD);
+ ew32(CTRL, ctrl);
+
+ /* Configure Flow Control after forcing link up. */
+ ret_val = e1000e_config_fc_after_link_up(hw);
+ if (ret_val) {
+ e_dbg("Error configuring flow control\n");
+ return ret_val;
+ }
+ } else if ((ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) {
+ /*
+ * If we are forcing link and we are receiving /C/ ordered
+ * sets, re-enable auto-negotiation in the TXCW register
+ * and disable forced link in the Device Control register
+ * in an attempt to auto-negotiate with our link partner.
+ */
+ e_dbg("Rx'ing /C/, enable AutoNeg and stop forcing link.\n");
+ ew32(TXCW, mac->txcw);
+ ew32(CTRL, (ctrl & ~E1000_CTRL_SLU));
+
+ mac->serdes_has_link = true;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_check_for_serdes_link - Check for link (Serdes)
+ * @hw: pointer to the HW structure
+ *
+ * Checks for link up on the hardware. If link is not up and we have
+ * a signal, then we need to force link up.
+ **/
+s32 e1000e_check_for_serdes_link(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ u32 rxcw;
+ u32 ctrl;
+ u32 status;
+ s32 ret_val;
+
+ ctrl = er32(CTRL);
+ status = er32(STATUS);
+ rxcw = er32(RXCW);
+
+ /*
+ * If we don't have link (auto-negotiation failed or link partner
+ * cannot auto-negotiate), and our link partner is not trying to
+ * auto-negotiate with us (we are receiving idles or data),
+ * we need to force link up. We also need to give auto-negotiation
+ * time to complete.
+ */
+ /* (ctrl & E1000_CTRL_SWDPIN1) == 1 == have signal */
+ if (!(status & E1000_STATUS_LU) && !(rxcw & E1000_RXCW_C)) {
+ if (!mac->autoneg_failed) {
+ mac->autoneg_failed = true;
+ return 0;
+ }
+ e_dbg("NOT Rx'ing /C/, disable AutoNeg and force link.\n");
+
+ /* Disable auto-negotiation in the TXCW register */
+ ew32(TXCW, (mac->txcw & ~E1000_TXCW_ANE));
+
+ /* Force link-up and also force full-duplex. */
+ ctrl = er32(CTRL);
+ ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD);
+ ew32(CTRL, ctrl);
+
+ /* Configure Flow Control after forcing link up. */
+ ret_val = e1000e_config_fc_after_link_up(hw);
+ if (ret_val) {
+ e_dbg("Error configuring flow control\n");
+ return ret_val;
+ }
+ } else if ((ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) {
+ /*
+ * If we are forcing link and we are receiving /C/ ordered
+ * sets, re-enable auto-negotiation in the TXCW register
+ * and disable forced link in the Device Control register
+ * in an attempt to auto-negotiate with our link partner.
+ */
+ e_dbg("Rx'ing /C/, enable AutoNeg and stop forcing link.\n");
+ ew32(TXCW, mac->txcw);
+ ew32(CTRL, (ctrl & ~E1000_CTRL_SLU));
+
+ mac->serdes_has_link = true;
+ } else if (!(E1000_TXCW_ANE & er32(TXCW))) {
+ /*
+ * If we force link for non-auto-negotiation switch, check
+ * link status based on MAC synchronization for internal
+ * serdes media type.
+ */
+ /* SYNCH bit and IV bit are sticky. */
+ udelay(10);
+ rxcw = er32(RXCW);
+ if (rxcw & E1000_RXCW_SYNCH) {
+ if (!(rxcw & E1000_RXCW_IV)) {
+ mac->serdes_has_link = true;
+ e_dbg("SERDES: Link up - forced.\n");
+ }
+ } else {
+ mac->serdes_has_link = false;
+ e_dbg("SERDES: Link down - force failed.\n");
+ }
+ }
+
+ if (E1000_TXCW_ANE & er32(TXCW)) {
+ status = er32(STATUS);
+ if (status & E1000_STATUS_LU) {
+ /* SYNCH bit and IV bit are sticky, so reread rxcw. */
+ udelay(10);
+ rxcw = er32(RXCW);
+ if (rxcw & E1000_RXCW_SYNCH) {
+ if (!(rxcw & E1000_RXCW_IV)) {
+ mac->serdes_has_link = true;
+ e_dbg("SERDES: Link up - autoneg completed successfully.\n");
+ } else {
+ mac->serdes_has_link = false;
+ e_dbg("SERDES: Link down - invalid codewords detected in autoneg.\n");
+ }
+ } else {
+ mac->serdes_has_link = false;
+ e_dbg("SERDES: Link down - no sync.\n");
+ }
+ } else {
+ mac->serdes_has_link = false;
+ e_dbg("SERDES: Link down - autoneg failed\n");
+ }
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_set_default_fc_generic - Set flow control default values
+ * @hw: pointer to the HW structure
+ *
+ * Read the EEPROM for the default values for flow control and store the
+ * values.
+ **/
+static s32 e1000_set_default_fc_generic(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 nvm_data;
+
+ /*
+ * Read and store word 0x0F of the EEPROM. This word contains bits
+ * that determine the hardware's default PAUSE (flow control) mode,
+ * a bit that determines whether the HW defaults to enabling or
+ * disabling auto-negotiation, and the direction of the
+ * SW defined pins. If there is no SW over-ride of the flow
+ * control setting, then the variable hw->fc will
+ * be initialized based on a value in the EEPROM.
+ */
+ ret_val = e1000_read_nvm(hw, NVM_INIT_CONTROL2_REG, 1, &nvm_data);
+
+ if (ret_val) {
+ e_dbg("NVM Read Error\n");
+ return ret_val;
+ }
+
+ if ((nvm_data & NVM_WORD0F_PAUSE_MASK) == 0)
+ hw->fc.requested_mode = e1000_fc_none;
+ else if ((nvm_data & NVM_WORD0F_PAUSE_MASK) == NVM_WORD0F_ASM_DIR)
+ hw->fc.requested_mode = e1000_fc_tx_pause;
+ else
+ hw->fc.requested_mode = e1000_fc_full;
+
+ return 0;
+}
+
+/**
+ * e1000e_setup_link_generic - Setup flow control and link settings
+ * @hw: pointer to the HW structure
+ *
+ * Determines which flow control settings to use, then configures flow
+ * control. Calls the appropriate media-specific link configuration
+ * function. Assuming the adapter has a valid link partner, a valid link
+ * should be established. Assumes the hardware has previously been reset
+ * and the transmitter and receiver are not enabled.
+ **/
+s32 e1000e_setup_link_generic(struct e1000_hw *hw)
+{
+ s32 ret_val;
+
+ /*
+ * In the case of the phy reset being blocked, we already have a link.
+ * We do not need to set it up again.
+ */
+ if (hw->phy.ops.check_reset_block(hw))
+ return 0;
+
+ /*
+ * If requested flow control is set to default, set flow control
+ * based on the EEPROM flow control settings.
+ */
+ if (hw->fc.requested_mode == e1000_fc_default) {
+ ret_val = e1000_set_default_fc_generic(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /*
+ * Save off the requested flow control mode for use later. Depending
+ * on the link partner's capabilities, we may or may not use this mode.
+ */
+ hw->fc.current_mode = hw->fc.requested_mode;
+
+ e_dbg("After fix-ups FlowControl is now = %x\n", hw->fc.current_mode);
+
+ /* Call the necessary media_type subroutine to configure the link. */
+ ret_val = hw->mac.ops.setup_physical_interface(hw);
+ if (ret_val)
+ return ret_val;
+
+ /*
+ * Initialize the flow control address, type, and PAUSE timer
+ * registers to their default values. This is done even if flow
+ * control is disabled, because it does not hurt anything to
+ * initialize these registers.
+ */
+ e_dbg("Initializing the Flow Control address, type and timer regs\n");
+ ew32(FCT, FLOW_CONTROL_TYPE);
+ ew32(FCAH, FLOW_CONTROL_ADDRESS_HIGH);
+ ew32(FCAL, FLOW_CONTROL_ADDRESS_LOW);
+
+ ew32(FCTTV, hw->fc.pause_time);
+
+ return e1000e_set_fc_watermarks(hw);
+}
+
+/**
+ * e1000_commit_fc_settings_generic - Configure flow control
+ * @hw: pointer to the HW structure
+ *
+ * Write the flow control settings to the Transmit Config Word Register (TXCW)
+ * base on the flow control settings in e1000_mac_info.
+ **/
+static s32 e1000_commit_fc_settings_generic(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ u32 txcw;
+
+ /*
+ * Check for a software override of the flow control settings, and
+ * setup the device accordingly. If auto-negotiation is enabled, then
+ * software will have to set the "PAUSE" bits to the correct value in
+ * the Transmit Config Word Register (TXCW) and re-start auto-
+ * negotiation. However, if auto-negotiation is disabled, then
+ * software will have to manually configure the two flow control enable
+ * bits in the CTRL register.
+ *
+ * The possible values of the "fc" parameter are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause frames,
+ * but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames but we
+ * do not support receiving pause frames).
+ * 3: Both Rx and Tx flow control (symmetric) are enabled.
+ */
+ switch (hw->fc.current_mode) {
+ case e1000_fc_none:
+ /* Flow control completely disabled by a software over-ride. */
+ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD);
+ break;
+ case e1000_fc_rx_pause:
+ /*
+ * Rx Flow control is enabled and Tx Flow control is disabled
+ * by a software over-ride. Since there really isn't a way to
+ * advertise that we are capable of Rx Pause ONLY, we will
+ * advertise that we support both symmetric and asymmetric Rx
+ * PAUSE. Later, we will disable the adapter's ability to send
+ * PAUSE frames.
+ */
+ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
+ break;
+ case e1000_fc_tx_pause:
+ /*
+ * Tx Flow control is enabled, and Rx Flow control is disabled,
+ * by a software over-ride.
+ */
+ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_ASM_DIR);
+ break;
+ case e1000_fc_full:
+ /*
+ * Flow control (both Rx and Tx) is enabled by a software
+ * over-ride.
+ */
+ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
+ break;
+ default:
+ e_dbg("Flow control param set incorrectly\n");
+ return -E1000_ERR_CONFIG;
+ break;
+ }
+
+ ew32(TXCW, txcw);
+ mac->txcw = txcw;
+
+ return 0;
+}
+
+/**
+ * e1000_poll_fiber_serdes_link_generic - Poll for link up
+ * @hw: pointer to the HW structure
+ *
+ * Polls for link up by reading the status register, if link fails to come
+ * up with auto-negotiation, then the link is forced if a signal is detected.
+ **/
+static s32 e1000_poll_fiber_serdes_link_generic(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ u32 i, status;
+ s32 ret_val;
+
+ /*
+ * If we have a signal (the cable is plugged in, or assumed true for
+ * serdes media) then poll for a "Link-Up" indication in the Device
+ * Status Register. Time-out if a link isn't seen in 500 milliseconds
+ * seconds (Auto-negotiation should complete in less than 500
+ * milliseconds even if the other end is doing it in SW).
+ */
+ for (i = 0; i < FIBER_LINK_UP_LIMIT; i++) {
+ usleep_range(10000, 20000);
+ status = er32(STATUS);
+ if (status & E1000_STATUS_LU)
+ break;
+ }
+ if (i == FIBER_LINK_UP_LIMIT) {
+ e_dbg("Never got a valid link from auto-neg!!!\n");
+ mac->autoneg_failed = true;
+ /*
+ * AutoNeg failed to achieve a link, so we'll call
+ * mac->check_for_link. This routine will force the
+ * link up if we detect a signal. This will allow us to
+ * communicate with non-autonegotiating link partners.
+ */
+ ret_val = mac->ops.check_for_link(hw);
+ if (ret_val) {
+ e_dbg("Error while checking for link\n");
+ return ret_val;
+ }
+ mac->autoneg_failed = false;
+ } else {
+ mac->autoneg_failed = false;
+ e_dbg("Valid Link Found\n");
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_setup_fiber_serdes_link - Setup link for fiber/serdes
+ * @hw: pointer to the HW structure
+ *
+ * Configures collision distance and flow control for fiber and serdes
+ * links. Upon successful setup, poll for link.
+ **/
+s32 e1000e_setup_fiber_serdes_link(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ s32 ret_val;
+
+ ctrl = er32(CTRL);
+
+ /* Take the link out of reset */
+ ctrl &= ~E1000_CTRL_LRST;
+
+ hw->mac.ops.config_collision_dist(hw);
+
+ ret_val = e1000_commit_fc_settings_generic(hw);
+ if (ret_val)
+ return ret_val;
+
+ /*
+ * Since auto-negotiation is enabled, take the link out of reset (the
+ * link will be in reset, because we previously reset the chip). This
+ * will restart auto-negotiation. If auto-negotiation is successful
+ * then the link-up status bit will be set and the flow control enable
+ * bits (RFCE and TFCE) will be set according to their negotiated value.
+ */
+ e_dbg("Auto-negotiation enabled\n");
+
+ ew32(CTRL, ctrl);
+ e1e_flush();
+ usleep_range(1000, 2000);
+
+ /*
+ * For these adapters, the SW definable pin 1 is set when the optics
+ * detect a signal. If we have a signal, then poll for a "Link-Up"
+ * indication.
+ */
+ if (hw->phy.media_type == e1000_media_type_internal_serdes ||
+ (er32(CTRL) & E1000_CTRL_SWDPIN1)) {
+ ret_val = e1000_poll_fiber_serdes_link_generic(hw);
+ } else {
+ e_dbg("No signal detected\n");
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000e_config_collision_dist_generic - Configure collision distance
+ * @hw: pointer to the HW structure
+ *
+ * Configures the collision distance to the default value and is used
+ * during link setup.
+ **/
+void e1000e_config_collision_dist_generic(struct e1000_hw *hw)
+{
+ u32 tctl;
+
+ tctl = er32(TCTL);
+
+ tctl &= ~E1000_TCTL_COLD;
+ tctl |= E1000_COLLISION_DISTANCE << E1000_COLD_SHIFT;
+
+ ew32(TCTL, tctl);
+ e1e_flush();
+}
+
+/**
+ * e1000e_set_fc_watermarks - Set flow control high/low watermarks
+ * @hw: pointer to the HW structure
+ *
+ * Sets the flow control high/low threshold (watermark) registers. If
+ * flow control XON frame transmission is enabled, then set XON frame
+ * transmission as well.
+ **/
+s32 e1000e_set_fc_watermarks(struct e1000_hw *hw)
+{
+ u32 fcrtl = 0, fcrth = 0;
+
+ /*
+ * Set the flow control receive threshold registers. Normally,
+ * these registers will be set to a default threshold that may be
+ * adjusted later by the driver's runtime code. However, if the
+ * ability to transmit pause frames is not enabled, then these
+ * registers will be set to 0.
+ */
+ if (hw->fc.current_mode & e1000_fc_tx_pause) {
+ /*
+ * We need to set up the Receive Threshold high and low water
+ * marks as well as (optionally) enabling the transmission of
+ * XON frames.
+ */
+ fcrtl = hw->fc.low_water;
+ if (hw->fc.send_xon)
+ fcrtl |= E1000_FCRTL_XONE;
+
+ fcrth = hw->fc.high_water;
+ }
+ ew32(FCRTL, fcrtl);
+ ew32(FCRTH, fcrth);
+
+ return 0;
+}
+
+/**
+ * e1000e_force_mac_fc - Force the MAC's flow control settings
+ * @hw: pointer to the HW structure
+ *
+ * Force the MAC's flow control settings. Sets the TFCE and RFCE bits in the
+ * device control register to reflect the adapter settings. TFCE and RFCE
+ * need to be explicitly set by software when a copper PHY is used because
+ * autonegotiation is managed by the PHY rather than the MAC. Software must
+ * also configure these bits when link is forced on a fiber connection.
+ **/
+s32 e1000e_force_mac_fc(struct e1000_hw *hw)
+{
+ u32 ctrl;
+
+ ctrl = er32(CTRL);
+
+ /*
+ * Because we didn't get link via the internal auto-negotiation
+ * mechanism (we either forced link or we got link via PHY
+ * auto-neg), we have to manually enable/disable transmit an
+ * receive flow control.
+ *
+ * The "Case" statement below enables/disable flow control
+ * according to the "hw->fc.current_mode" parameter.
+ *
+ * The possible values of the "fc" parameter are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause
+ * frames but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames
+ * frames but we do not receive pause frames).
+ * 3: Both Rx and Tx flow control (symmetric) is enabled.
+ * other: No other values should be possible at this point.
+ */
+ e_dbg("hw->fc.current_mode = %u\n", hw->fc.current_mode);
+
+ switch (hw->fc.current_mode) {
+ case e1000_fc_none:
+ ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE));
+ break;
+ case e1000_fc_rx_pause:
+ ctrl &= (~E1000_CTRL_TFCE);
+ ctrl |= E1000_CTRL_RFCE;
+ break;
+ case e1000_fc_tx_pause:
+ ctrl &= (~E1000_CTRL_RFCE);
+ ctrl |= E1000_CTRL_TFCE;
+ break;
+ case e1000_fc_full:
+ ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE);
+ break;
+ default:
+ e_dbg("Flow control param set incorrectly\n");
+ return -E1000_ERR_CONFIG;
+ }
+
+ ew32(CTRL, ctrl);
+
+ return 0;
+}
+
+/**
+ * e1000e_config_fc_after_link_up - Configures flow control after link
+ * @hw: pointer to the HW structure
+ *
+ * Checks the status of auto-negotiation after link up to ensure that the
+ * speed and duplex were not forced. If the link needed to be forced, then
+ * flow control needs to be forced also. If auto-negotiation is enabled
+ * and did not fail, then we configure flow control based on our link
+ * partner.
+ **/
+s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ s32 ret_val = 0;
+ u16 mii_status_reg, mii_nway_adv_reg, mii_nway_lp_ability_reg;
+ u16 speed, duplex;
+
+ /*
+ * Check for the case where we have fiber media and auto-neg failed
+ * so we had to force link. In this case, we need to force the
+ * configuration of the MAC to match the "fc" parameter.
+ */
+ if (mac->autoneg_failed) {
+ if (hw->phy.media_type == e1000_media_type_fiber ||
+ hw->phy.media_type == e1000_media_type_internal_serdes)
+ ret_val = e1000e_force_mac_fc(hw);
+ } else {
+ if (hw->phy.media_type == e1000_media_type_copper)
+ ret_val = e1000e_force_mac_fc(hw);
+ }
+
+ if (ret_val) {
+ e_dbg("Error forcing flow control settings\n");
+ return ret_val;
+ }
+
+ /*
+ * Check for the case where we have copper media and auto-neg is
+ * enabled. In this case, we need to check and see if Auto-Neg
+ * has completed, and if so, how the PHY and link partner has
+ * flow control configured.
+ */
+ if ((hw->phy.media_type == e1000_media_type_copper) && mac->autoneg) {
+ /*
+ * Read the MII Status Register and check to see if AutoNeg
+ * has completed. We read this twice because this reg has
+ * some "sticky" (latched) bits.
+ */
+ ret_val = e1e_rphy(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1e_rphy(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+
+ if (!(mii_status_reg & MII_SR_AUTONEG_COMPLETE)) {
+ e_dbg("Copper PHY and Auto Neg has not completed.\n");
+ return ret_val;
+ }
+
+ /*
+ * The AutoNeg process has completed, so we now need to
+ * read both the Auto Negotiation Advertisement
+ * Register (Address 4) and the Auto_Negotiation Base
+ * Page Ability Register (Address 5) to determine how
+ * flow control was negotiated.
+ */
+ ret_val = e1e_rphy(hw, PHY_AUTONEG_ADV, &mii_nway_adv_reg);
+ if (ret_val)
+ return ret_val;
+ ret_val =
+ e1e_rphy(hw, PHY_LP_ABILITY, &mii_nway_lp_ability_reg);
+ if (ret_val)
+ return ret_val;
+
+ /*
+ * Two bits in the Auto Negotiation Advertisement Register
+ * (Address 4) and two bits in the Auto Negotiation Base
+ * Page Ability Register (Address 5) determine flow control
+ * for both the PHY and the link partner. The following
+ * table, taken out of the IEEE 802.3ab/D6.0 dated March 25,
+ * 1999, describes these PAUSE resolution bits and how flow
+ * control is determined based upon these settings.
+ * NOTE: DC = Don't Care
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution
+ *-------|---------|-------|---------|--------------------
+ * 0 | 0 | DC | DC | e1000_fc_none
+ * 0 | 1 | 0 | DC | e1000_fc_none
+ * 0 | 1 | 1 | 0 | e1000_fc_none
+ * 0 | 1 | 1 | 1 | e1000_fc_tx_pause
+ * 1 | 0 | 0 | DC | e1000_fc_none
+ * 1 | DC | 1 | DC | e1000_fc_full
+ * 1 | 1 | 0 | 0 | e1000_fc_none
+ * 1 | 1 | 0 | 1 | e1000_fc_rx_pause
+ *
+ * Are both PAUSE bits set to 1? If so, this implies
+ * Symmetric Flow Control is enabled at both ends. The
+ * ASM_DIR bits are irrelevant per the spec.
+ *
+ * For Symmetric Flow Control:
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 1 | DC | 1 | DC | E1000_fc_full
+ *
+ */
+ if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) {
+ /*
+ * Now we need to check if the user selected Rx ONLY
+ * of pause frames. In this case, we had to advertise
+ * FULL flow control because we could not advertise Rx
+ * ONLY. Hence, we must now check to see if we need to
+ * turn OFF the TRANSMISSION of PAUSE frames.
+ */
+ if (hw->fc.requested_mode == e1000_fc_full) {
+ hw->fc.current_mode = e1000_fc_full;
+ e_dbg("Flow Control = FULL.\n");
+ } else {
+ hw->fc.current_mode = e1000_fc_rx_pause;
+ e_dbg("Flow Control = Rx PAUSE frames only.\n");
+ }
+ }
+ /*
+ * For receiving PAUSE frames ONLY.
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 0 | 1 | 1 | 1 | e1000_fc_tx_pause
+ */
+ else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
+ hw->fc.current_mode = e1000_fc_tx_pause;
+ e_dbg("Flow Control = Tx PAUSE frames only.\n");
+ }
+ /*
+ * For transmitting PAUSE frames ONLY.
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 1 | 1 | 0 | 1 | e1000_fc_rx_pause
+ */
+ else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
+ !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
+ hw->fc.current_mode = e1000_fc_rx_pause;
+ e_dbg("Flow Control = Rx PAUSE frames only.\n");
+ } else {
+ /*
+ * Per the IEEE spec, at this point flow control
+ * should be disabled.
+ */
+ hw->fc.current_mode = e1000_fc_none;
+ e_dbg("Flow Control = NONE.\n");
+ }
+
+ /*
+ * Now we need to do one last check... If we auto-
+ * negotiated to HALF DUPLEX, flow control should not be
+ * enabled per IEEE 802.3 spec.
+ */
+ ret_val = mac->ops.get_link_up_info(hw, &speed, &duplex);
+ if (ret_val) {
+ e_dbg("Error getting link speed and duplex\n");
+ return ret_val;
+ }
+
+ if (duplex == HALF_DUPLEX)
+ hw->fc.current_mode = e1000_fc_none;
+
+ /*
+ * Now we call a subroutine to actually force the MAC
+ * controller to use the correct flow control settings.
+ */
+ ret_val = e1000e_force_mac_fc(hw);
+ if (ret_val) {
+ e_dbg("Error forcing flow control settings\n");
+ return ret_val;
+ }
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_get_speed_and_duplex_copper - Retrieve current speed/duplex
+ * @hw: pointer to the HW structure
+ * @speed: stores the current speed
+ * @duplex: stores the current duplex
+ *
+ * Read the status register for the current speed/duplex and store the current
+ * speed and duplex for copper connections.
+ **/
+s32 e1000e_get_speed_and_duplex_copper(struct e1000_hw *hw, u16 *speed,
+ u16 *duplex)
+{
+ u32 status;
+
+ status = er32(STATUS);
+ if (status & E1000_STATUS_SPEED_1000)
+ *speed = SPEED_1000;
+ else if (status & E1000_STATUS_SPEED_100)
+ *speed = SPEED_100;
+ else
+ *speed = SPEED_10;
+
+ if (status & E1000_STATUS_FD)
+ *duplex = FULL_DUPLEX;
+ else
+ *duplex = HALF_DUPLEX;
+
+ e_dbg("%u Mbps, %s Duplex\n",
+ *speed == SPEED_1000 ? 1000 : *speed == SPEED_100 ? 100 : 10,
+ *duplex == FULL_DUPLEX ? "Full" : "Half");
+
+ return 0;
+}
+
+/**
+ * e1000e_get_speed_and_duplex_fiber_serdes - Retrieve current speed/duplex
+ * @hw: pointer to the HW structure
+ * @speed: stores the current speed
+ * @duplex: stores the current duplex
+ *
+ * Sets the speed and duplex to gigabit full duplex (the only possible option)
+ * for fiber/serdes links.
+ **/
+s32 e1000e_get_speed_and_duplex_fiber_serdes(struct e1000_hw *hw, u16 *speed,
+ u16 *duplex)
+{
+ *speed = SPEED_1000;
+ *duplex = FULL_DUPLEX;
+
+ return 0;
+}
+
+/**
+ * e1000e_get_hw_semaphore - Acquire hardware semaphore
+ * @hw: pointer to the HW structure
+ *
+ * Acquire the HW semaphore to access the PHY or NVM
+ **/
+s32 e1000e_get_hw_semaphore(struct e1000_hw *hw)
+{
+ u32 swsm;
+ s32 timeout = hw->nvm.word_size + 1;
+ s32 i = 0;
+
+ /* Get the SW semaphore */
+ while (i < timeout) {
+ swsm = er32(SWSM);
+ if (!(swsm & E1000_SWSM_SMBI))
+ break;
+
+ udelay(50);
+ i++;
+ }
+
+ if (i == timeout) {
+ e_dbg("Driver can't access device - SMBI bit is set.\n");
+ return -E1000_ERR_NVM;
+ }
+
+ /* Get the FW semaphore. */
+ for (i = 0; i < timeout; i++) {
+ swsm = er32(SWSM);
+ ew32(SWSM, swsm | E1000_SWSM_SWESMBI);
+
+ /* Semaphore acquired if bit latched */
+ if (er32(SWSM) & E1000_SWSM_SWESMBI)
+ break;
+
+ udelay(50);
+ }
+
+ if (i == timeout) {
+ /* Release semaphores */
+ e1000e_put_hw_semaphore(hw);
+ e_dbg("Driver can't access the NVM\n");
+ return -E1000_ERR_NVM;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_put_hw_semaphore - Release hardware semaphore
+ * @hw: pointer to the HW structure
+ *
+ * Release hardware semaphore used to access the PHY or NVM
+ **/
+void e1000e_put_hw_semaphore(struct e1000_hw *hw)
+{
+ u32 swsm;
+
+ swsm = er32(SWSM);
+ swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI);
+ ew32(SWSM, swsm);
+}
+
+/**
+ * e1000e_get_auto_rd_done - Check for auto read completion
+ * @hw: pointer to the HW structure
+ *
+ * Check EEPROM for Auto Read done bit.
+ **/
+s32 e1000e_get_auto_rd_done(struct e1000_hw *hw)
+{
+ s32 i = 0;
+
+ while (i < AUTO_READ_DONE_TIMEOUT) {
+ if (er32(EECD) & E1000_EECD_AUTO_RD)
+ break;
+ usleep_range(1000, 2000);
+ i++;
+ }
+
+ if (i == AUTO_READ_DONE_TIMEOUT) {
+ e_dbg("Auto read by HW from NVM has not completed.\n");
+ return -E1000_ERR_RESET;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_valid_led_default - Verify a valid default LED config
+ * @hw: pointer to the HW structure
+ * @data: pointer to the NVM (EEPROM)
+ *
+ * Read the EEPROM for the current default LED configuration. If the
+ * LED configuration is not valid, set to a valid LED configuration.
+ **/
+s32 e1000e_valid_led_default(struct e1000_hw *hw, u16 *data)
+{
+ s32 ret_val;
+
+ ret_val = e1000_read_nvm(hw, NVM_ID_LED_SETTINGS, 1, data);
+ if (ret_val) {
+ e_dbg("NVM Read Error\n");
+ return ret_val;
+ }
+
+ if (*data == ID_LED_RESERVED_0000 || *data == ID_LED_RESERVED_FFFF)
+ *data = ID_LED_DEFAULT;
+
+ return 0;
+}
+
+/**
+ * e1000e_id_led_init_generic -
+ * @hw: pointer to the HW structure
+ *
+ **/
+s32 e1000e_id_led_init_generic(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ s32 ret_val;
+ const u32 ledctl_mask = 0x000000FF;
+ const u32 ledctl_on = E1000_LEDCTL_MODE_LED_ON;
+ const u32 ledctl_off = E1000_LEDCTL_MODE_LED_OFF;
+ u16 data, i, temp;
+ const u16 led_mask = 0x0F;
+
+ ret_val = hw->nvm.ops.valid_led_default(hw, &data);
+ if (ret_val)
+ return ret_val;
+
+ mac->ledctl_default = er32(LEDCTL);
+ mac->ledctl_mode1 = mac->ledctl_default;
+ mac->ledctl_mode2 = mac->ledctl_default;
+
+ for (i = 0; i < 4; i++) {
+ temp = (data >> (i << 2)) & led_mask;
+ switch (temp) {
+ case ID_LED_ON1_DEF2:
+ case ID_LED_ON1_ON2:
+ case ID_LED_ON1_OFF2:
+ mac->ledctl_mode1 &= ~(ledctl_mask << (i << 3));
+ mac->ledctl_mode1 |= ledctl_on << (i << 3);
+ break;
+ case ID_LED_OFF1_DEF2:
+ case ID_LED_OFF1_ON2:
+ case ID_LED_OFF1_OFF2:
+ mac->ledctl_mode1 &= ~(ledctl_mask << (i << 3));
+ mac->ledctl_mode1 |= ledctl_off << (i << 3);
+ break;
+ default:
+ /* Do nothing */
+ break;
+ }
+ switch (temp) {
+ case ID_LED_DEF1_ON2:
+ case ID_LED_ON1_ON2:
+ case ID_LED_OFF1_ON2:
+ mac->ledctl_mode2 &= ~(ledctl_mask << (i << 3));
+ mac->ledctl_mode2 |= ledctl_on << (i << 3);
+ break;
+ case ID_LED_DEF1_OFF2:
+ case ID_LED_ON1_OFF2:
+ case ID_LED_OFF1_OFF2:
+ mac->ledctl_mode2 &= ~(ledctl_mask << (i << 3));
+ mac->ledctl_mode2 |= ledctl_off << (i << 3);
+ break;
+ default:
+ /* Do nothing */
+ break;
+ }
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_setup_led_generic - Configures SW controllable LED
+ * @hw: pointer to the HW structure
+ *
+ * This prepares the SW controllable LED for use and saves the current state
+ * of the LED so it can be later restored.
+ **/
+s32 e1000e_setup_led_generic(struct e1000_hw *hw)
+{
+ u32 ledctl;
+
+ if (hw->mac.ops.setup_led != e1000e_setup_led_generic)
+ return -E1000_ERR_CONFIG;
+
+ if (hw->phy.media_type == e1000_media_type_fiber) {
+ ledctl = er32(LEDCTL);
+ hw->mac.ledctl_default = ledctl;
+ /* Turn off LED0 */
+ ledctl &= ~(E1000_LEDCTL_LED0_IVRT | E1000_LEDCTL_LED0_BLINK |
+ E1000_LEDCTL_LED0_MODE_MASK);
+ ledctl |= (E1000_LEDCTL_MODE_LED_OFF <<
+ E1000_LEDCTL_LED0_MODE_SHIFT);
+ ew32(LEDCTL, ledctl);
+ } else if (hw->phy.media_type == e1000_media_type_copper) {
+ ew32(LEDCTL, hw->mac.ledctl_mode1);
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_cleanup_led_generic - Set LED config to default operation
+ * @hw: pointer to the HW structure
+ *
+ * Remove the current LED configuration and set the LED configuration
+ * to the default value, saved from the EEPROM.
+ **/
+s32 e1000e_cleanup_led_generic(struct e1000_hw *hw)
+{
+ ew32(LEDCTL, hw->mac.ledctl_default);
+ return 0;
+}
+
+/**
+ * e1000e_blink_led_generic - Blink LED
+ * @hw: pointer to the HW structure
+ *
+ * Blink the LEDs which are set to be on.
+ **/
+s32 e1000e_blink_led_generic(struct e1000_hw *hw)
+{
+ u32 ledctl_blink = 0;
+ u32 i;
+
+ if (hw->phy.media_type == e1000_media_type_fiber) {
+ /* always blink LED0 for PCI-E fiber */
+ ledctl_blink = E1000_LEDCTL_LED0_BLINK |
+ (E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED0_MODE_SHIFT);
+ } else {
+ /*
+ * set the blink bit for each LED that's "on" (0x0E)
+ * in ledctl_mode2
+ */
+ ledctl_blink = hw->mac.ledctl_mode2;
+ for (i = 0; i < 4; i++)
+ if (((hw->mac.ledctl_mode2 >> (i * 8)) & 0xFF) ==
+ E1000_LEDCTL_MODE_LED_ON)
+ ledctl_blink |= (E1000_LEDCTL_LED0_BLINK <<
+ (i * 8));
+ }
+
+ ew32(LEDCTL, ledctl_blink);
+
+ return 0;
+}
+
+/**
+ * e1000e_led_on_generic - Turn LED on
+ * @hw: pointer to the HW structure
+ *
+ * Turn LED on.
+ **/
+s32 e1000e_led_on_generic(struct e1000_hw *hw)
+{
+ u32 ctrl;
+
+ switch (hw->phy.media_type) {
+ case e1000_media_type_fiber:
+ ctrl = er32(CTRL);
+ ctrl &= ~E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ ew32(CTRL, ctrl);
+ break;
+ case e1000_media_type_copper:
+ ew32(LEDCTL, hw->mac.ledctl_mode2);
+ break;
+ default:
+ break;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_led_off_generic - Turn LED off
+ * @hw: pointer to the HW structure
+ *
+ * Turn LED off.
+ **/
+s32 e1000e_led_off_generic(struct e1000_hw *hw)
+{
+ u32 ctrl;
+
+ switch (hw->phy.media_type) {
+ case e1000_media_type_fiber:
+ ctrl = er32(CTRL);
+ ctrl |= E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ ew32(CTRL, ctrl);
+ break;
+ case e1000_media_type_copper:
+ ew32(LEDCTL, hw->mac.ledctl_mode1);
+ break;
+ default:
+ break;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_set_pcie_no_snoop - Set PCI-express capabilities
+ * @hw: pointer to the HW structure
+ * @no_snoop: bitmap of snoop events
+ *
+ * Set the PCI-express register to snoop for events enabled in 'no_snoop'.
+ **/
+void e1000e_set_pcie_no_snoop(struct e1000_hw *hw, u32 no_snoop)
+{
+ u32 gcr;
+
+ if (no_snoop) {
+ gcr = er32(GCR);
+ gcr &= ~(PCIE_NO_SNOOP_ALL);
+ gcr |= no_snoop;
+ ew32(GCR, gcr);
+ }
+}
+
+/**
+ * e1000e_disable_pcie_master - Disables PCI-express master access
+ * @hw: pointer to the HW structure
+ *
+ * Returns 0 if successful, else returns -10
+ * (-E1000_ERR_MASTER_REQUESTS_PENDING) if master disable bit has not caused
+ * the master requests to be disabled.
+ *
+ * Disables PCI-Express master access and verifies there are no pending
+ * requests.
+ **/
+s32 e1000e_disable_pcie_master(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ s32 timeout = MASTER_DISABLE_TIMEOUT;
+
+ ctrl = er32(CTRL);
+ ctrl |= E1000_CTRL_GIO_MASTER_DISABLE;
+ ew32(CTRL, ctrl);
+
+ while (timeout) {
+ if (!(er32(STATUS) & E1000_STATUS_GIO_MASTER_ENABLE))
+ break;
+ udelay(100);
+ timeout--;
+ }
+
+ if (!timeout) {
+ e_dbg("Master requests are pending.\n");
+ return -E1000_ERR_MASTER_REQUESTS_PENDING;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_reset_adaptive - Reset Adaptive Interframe Spacing
+ * @hw: pointer to the HW structure
+ *
+ * Reset the Adaptive Interframe Spacing throttle to default values.
+ **/
+void e1000e_reset_adaptive(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+
+ if (!mac->adaptive_ifs) {
+ e_dbg("Not in Adaptive IFS mode!\n");
+ return;
+ }
+
+ mac->current_ifs_val = 0;
+ mac->ifs_min_val = IFS_MIN;
+ mac->ifs_max_val = IFS_MAX;
+ mac->ifs_step_size = IFS_STEP;
+ mac->ifs_ratio = IFS_RATIO;
+
+ mac->in_ifs_mode = false;
+ ew32(AIT, 0);
+}
+
+/**
+ * e1000e_update_adaptive - Update Adaptive Interframe Spacing
+ * @hw: pointer to the HW structure
+ *
+ * Update the Adaptive Interframe Spacing Throttle value based on the
+ * time between transmitted packets and time between collisions.
+ **/
+void e1000e_update_adaptive(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+
+ if (!mac->adaptive_ifs) {
+ e_dbg("Not in Adaptive IFS mode!\n");
+ return;
+ }
+
+ if ((mac->collision_delta * mac->ifs_ratio) > mac->tx_packet_delta) {
+ if (mac->tx_packet_delta > MIN_NUM_XMITS) {
+ mac->in_ifs_mode = true;
+ if (mac->current_ifs_val < mac->ifs_max_val) {
+ if (!mac->current_ifs_val)
+ mac->current_ifs_val = mac->ifs_min_val;
+ else
+ mac->current_ifs_val +=
+ mac->ifs_step_size;
+ ew32(AIT, mac->current_ifs_val);
+ }
+ }
+ } else {
+ if (mac->in_ifs_mode &&
+ (mac->tx_packet_delta <= MIN_NUM_XMITS)) {
+ mac->current_ifs_val = 0;
+ mac->in_ifs_mode = false;
+ ew32(AIT, 0);
+ }
+ }
+}