summaryrefslogtreecommitdiff
path: root/ext/hal/st/stm32cube/stm32f1xx/drivers/include/stm32f1xx_hal_conf.h
diff options
context:
space:
mode:
Diffstat (limited to 'ext/hal/st/stm32cube/stm32f1xx/drivers/include/stm32f1xx_hal_conf.h')
-rw-r--r--ext/hal/st/stm32cube/stm32f1xx/drivers/include/stm32f1xx_hal_conf.h144
1 files changed, 80 insertions, 64 deletions
diff --git a/ext/hal/st/stm32cube/stm32f1xx/drivers/include/stm32f1xx_hal_conf.h b/ext/hal/st/stm32cube/stm32f1xx/drivers/include/stm32f1xx_hal_conf.h
index 9e84d74f8..0bd8d8aa2 100644
--- a/ext/hal/st/stm32cube/stm32f1xx/drivers/include/stm32f1xx_hal_conf.h
+++ b/ext/hal/st/stm32cube/stm32f1xx/drivers/include/stm32f1xx_hal_conf.h
@@ -2,15 +2,15 @@
******************************************************************************
* @file stm32f1xx_hal_conf.h
* @author MCD Application Team
- * @version V1.0.4
- * @date 29-April-2016
+ * @version V1.1.0
+ * @date 14-April-2017
* @brief HAL configuration template file.
* This file should be copied to the application folder and renamed
* to stm32f1xx_hal_conf.h.
******************************************************************************
* @attention
*
- * <h2><center>&copy; COPYRIGHT(c) 2016 STMicroelectronics</center></h2>
+ * <h2><center>&copy; COPYRIGHT(c) 2017 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
@@ -35,7 +35,7 @@
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
- */
+ */
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM32F1xx_HAL_CONF_H
@@ -50,7 +50,7 @@
/* ########################## Module Selection ############################## */
/**
- * @brief This is the list of modules to be used in the HAL driver
+ * @brief This is the list of modules to be used in the HAL driver
*/
#define HAL_MODULE_ENABLED
#define HAL_ADC_MODULE_ENABLED
@@ -83,103 +83,109 @@
#define HAL_UART_MODULE_ENABLED
#define HAL_USART_MODULE_ENABLED
#define HAL_WWDG_MODULE_ENABLED
+#define HAL_MMC_MODULE_ENABLED
/* ########################## Oscillator Values adaptation ####################*/
/**
* @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
* This value is used by the RCC HAL module to compute the system frequency
- * (when HSE is used as system clock source, directly or through the PLL).
+ * (when HSE is used as system clock source, directly or through the PLL).
*/
-#if !defined (HSE_VALUE)
+#if !defined (HSE_VALUE)
#if defined(USE_STM3210C_EVAL)
- #define HSE_VALUE ((uint32_t)25000000) /*!< Value of the External oscillator in Hz */
+ #define HSE_VALUE 25000000U /*!< Value of the External oscillator in Hz */
#else
- #define HSE_VALUE ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */
+ #define HSE_VALUE 8000000U /*!< Value of the External oscillator in Hz */
#endif
#endif /* HSE_VALUE */
#if !defined (HSE_STARTUP_TIMEOUT)
- #define HSE_STARTUP_TIMEOUT ((uint32_t)100) /*!< Time out for HSE start up, in ms */
+ #define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */
#endif /* HSE_STARTUP_TIMEOUT */
/**
* @brief Internal High Speed oscillator (HSI) value.
* This value is used by the RCC HAL module to compute the system frequency
- * (when HSI is used as system clock source, directly or through the PLL).
+ * (when HSI is used as system clock source, directly or through the PLL).
*/
#if !defined (HSI_VALUE)
- #define HSI_VALUE ((uint32_t)8000000) /*!< Value of the Internal oscillator in Hz*/
+ #define HSI_VALUE 8000000U /*!< Value of the Internal oscillator in Hz */
#endif /* HSI_VALUE */
/**
+ * @brief Internal Low Speed oscillator (LSI) value.
+ */
+#if !defined (LSI_VALUE)
+ #define LSI_VALUE 40000U /*!< LSI Typical Value in Hz */
+#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
+ The real value may vary depending on the variations
+ in voltage and temperature. */
+/**
* @brief External Low Speed oscillator (LSE) value.
* This value is used by the UART, RTC HAL module to compute the system frequency
*/
#if !defined (LSE_VALUE)
- #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External oscillator in Hz*/
+ #define LSE_VALUE 32768U /*!< Value of the External Low Speed oscillator in Hz */
#endif /* LSE_VALUE */
-
#if !defined (LSE_STARTUP_TIMEOUT)
- #define LSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for LSE start up, in ms */
-#endif /* HSE_STARTUP_TIMEOUT */
+ #define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */
+#endif /* LSE_STARTUP_TIMEOUT */
-
/* Tip: To avoid modifying this file each time you need to use different HSE,
=== you can define the HSE value in your toolchain compiler preprocessor. */
/* ########################### System Configuration ######################### */
/**
* @brief This is the HAL system configuration section
- */
-#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */
-#define TICK_INT_PRIORITY ((uint32_t)0x000F) /*!< tick interrupt priority */
-#define USE_RTOS 0
-#define PREFETCH_ENABLE 1
+ */
+#define VDD_VALUE 3300U /*!< Value of VDD in mv */
+#define TICK_INT_PRIORITY 0x0FU /*!< tick interrupt priority */
+#define USE_RTOS 0U
+#define PREFETCH_ENABLE 1U
/* ########################## Assert Selection ############################## */
/**
- * @brief Uncomment the line below to expanse the "assert_param" macro in the
+ * @brief Uncomment the line below to expanse the "assert_param" macro in the
* HAL drivers code
*/
-/*#define USE_FULL_ASSERT 1*/
-
+/* #define USE_FULL_ASSERT 1U */
/* ################## Ethernet peripheral configuration ##################### */
/* Section 1 : Ethernet peripheral configuration */
/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
-#define MAC_ADDR0 2
-#define MAC_ADDR1 0
-#define MAC_ADDR2 0
-#define MAC_ADDR3 0
-#define MAC_ADDR4 0
-#define MAC_ADDR5 0
-
-/* Definition of the Ethernet driver buffers size and count */
+#define MAC_ADDR0 2U
+#define MAC_ADDR1 0U
+#define MAC_ADDR2 0U
+#define MAC_ADDR3 0U
+#define MAC_ADDR4 0U
+#define MAC_ADDR5 0U
+
+/* Definition of the Ethernet driver buffers size and count */
#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */
#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */
-#define ETH_RXBUFNB ((uint32_t)8) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */
-#define ETH_TXBUFNB ((uint32_t)4) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */
+#define ETH_RXBUFNB 8U /* 8 Rx buffers of size ETH_RX_BUF_SIZE */
+#define ETH_TXBUFNB 4U /* 4 Tx buffers of size ETH_TX_BUF_SIZE */
/* Section 2: PHY configuration section */
-/* DP83848 PHY Address*/
-#define DP83848_PHY_ADDRESS 0x01
-/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
-#define PHY_RESET_DELAY ((uint32_t)0x000000FF)
+/* DP83848 PHY Address*/
+#define DP83848_PHY_ADDRESS 0x01U
+/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
+#define PHY_RESET_DELAY 0x000000FFU
/* PHY Configuration delay */
-#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFF)
+#define PHY_CONFIG_DELAY 0x00000FFFU
-#define PHY_READ_TO ((uint32_t)0x0000FFFF)
-#define PHY_WRITE_TO ((uint32_t)0x0000FFFF)
+#define PHY_READ_TO 0x0000FFFFU
+#define PHY_WRITE_TO 0x0000FFFFU
/* Section 3: Common PHY Registers */
-#define PHY_BCR ((uint16_t)0x00) /*!< Transceiver Basic Control Register */
-#define PHY_BSR ((uint16_t)0x01) /*!< Transceiver Basic Status Register */
-
+#define PHY_BCR ((uint16_t)0x0000) /*!< Transceiver Basic Control Register */
+#define PHY_BSR ((uint16_t)0x0001) /*!< Transceiver Basic Status Register */
+
#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */
#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */
#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */
@@ -194,13 +200,13 @@
#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */
#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */
#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */
-
+
/* Section 4: Extended PHY Registers */
-#define PHY_SR ((uint16_t)0x10) /*!< PHY status register Offset */
-#define PHY_MICR ((uint16_t)0x11) /*!< MII Interrupt Control Register */
-#define PHY_MISR ((uint16_t)0x12) /*!< MII Interrupt Status and Misc. Control Register */
-
+#define PHY_SR ((uint16_t)0x0010) /*!< PHY status register Offset */
+#define PHY_MICR ((uint16_t)0x0011) /*!< MII Interrupt Control Register */
+#define PHY_MISR ((uint16_t)0x0012) /*!< MII Interrupt Status and Misc. Control Register */
+
#define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */
#define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */
#define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */
@@ -211,11 +217,18 @@
#define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */
#define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */
+/* ################## SPI peripheral configuration ########################## */
+
+/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
+* Activated: CRC code is present inside driver
+* Deactivated: CRC code cleaned from driver
+*/
+#define USE_SPI_CRC 1U
/* Includes ------------------------------------------------------------------*/
/**
- * @brief Include module's header file
+ * @brief Include module's header file
*/
#ifdef HAL_RCC_MODULE_ENABLED
@@ -225,15 +238,15 @@
#ifdef HAL_GPIO_MODULE_ENABLED
#include "stm32f1xx_hal_gpio.h"
#endif /* HAL_GPIO_MODULE_ENABLED */
-
+
#ifdef HAL_DMA_MODULE_ENABLED
#include "stm32f1xx_hal_dma.h"
#endif /* HAL_DMA_MODULE_ENABLED */
-
+
#ifdef HAL_ETH_MODULE_ENABLED
#include "stm32f1xx_hal_eth.h"
-#endif /* HAL_ETH_MODULE_ENABLED */
-
+#endif /* HAL_ETH_MODULE_ENABLED */
+
#ifdef HAL_CAN_MODULE_ENABLED
#include "stm32f1xx_hal_can.h"
#endif /* HAL_CAN_MODULE_ENABLED */
@@ -292,15 +305,15 @@
#ifdef HAL_PCCARD_MODULE_ENABLED
#include "stm32f1xx_hal_pccard.h"
-#endif /* HAL_PCCARD_MODULE_ENABLED */
+#endif /* HAL_PCCARD_MODULE_ENABLED */
#ifdef HAL_SD_MODULE_ENABLED
#include "stm32f1xx_hal_sd.h"
-#endif /* HAL_SD_MODULE_ENABLED */
+#endif /* HAL_SD_MODULE_ENABLED */
#ifdef HAL_NAND_MODULE_ENABLED
#include "stm32f1xx_hal_nand.h"
-#endif /* HAL_NAND_MODULE_ENABLED */
+#endif /* HAL_NAND_MODULE_ENABLED */
#ifdef HAL_SPI_MODULE_ENABLED
#include "stm32f1xx_hal_spi.h"
@@ -334,11 +347,13 @@
#include "stm32f1xx_hal_pcd.h"
#endif /* HAL_PCD_MODULE_ENABLED */
-
#ifdef HAL_HCD_MODULE_ENABLED
#include "stm32f1xx_hal_hcd.h"
-#endif /* HAL_HCD_MODULE_ENABLED */
-
+#endif /* HAL_HCD_MODULE_ENABLED */
+
+#ifdef HAL_MMC_MODULE_ENABLED
+ #include "stm32f1xx_hal_mmc.h"
+#endif /* HAL_MMC_MODULE_ENABLED */
/* Exported macro ------------------------------------------------------------*/
#ifdef USE_FULL_ASSERT
@@ -346,17 +361,18 @@
* @brief The assert_param macro is used for function's parameters check.
* @param expr: If expr is false, it calls assert_failed function
* which reports the name of the source file and the source
- * line number of the call that failed.
+ * line number of the call that failed.
* If expr is true, it returns no value.
* @retval None
*/
- #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__))
+ #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
/* Exported functions ------------------------------------------------------- */
void assert_failed(uint8_t* file, uint32_t line);
#else
- #define assert_param(expr) ((void)0)
+ #define assert_param(expr) ((void)0U)
#endif /* USE_FULL_ASSERT */
+
#ifdef __cplusplus
}
#endif
generated by cgit v1.2.3 (git 2.25.1) at 2024-05-22 06:51:50 +0000