diff options
Diffstat (limited to 'drivers/net/wireless/ath/ath5k')
| -rw-r--r-- | drivers/net/wireless/ath/ath5k/base.h | 4 | ||||
| -rw-r--r-- | drivers/net/wireless/ath/ath5k/eeprom.c | 2 | ||||
| -rw-r--r-- | drivers/net/wireless/ath/ath5k/phy.c | 6 |
3 files changed, 6 insertions, 6 deletions
diff --git a/drivers/net/wireless/ath/ath5k/base.h b/drivers/net/wireless/ath/ath5k/base.h index b72338c9bde7..952b3a21bbc3 100644 --- a/drivers/net/wireless/ath/ath5k/base.h +++ b/drivers/net/wireless/ath/ath5k/base.h @@ -36,7 +36,7 @@ */ /* - * Defintions for the Atheros Wireless LAN controller driver. + * Definitions for the Atheros Wireless LAN controller driver. */ #ifndef _DEV_ATH_ATHVAR_H #define _DEV_ATH_ATHVAR_H @@ -190,7 +190,7 @@ struct ath5k_softc { struct ath5k_txq *cabq; /* content after beacon */ int power_level; /* Requested tx power in dbm */ - bool assoc; /* assocate state */ + bool assoc; /* associate state */ bool enable_beacon; /* true if beacons are on */ }; diff --git a/drivers/net/wireless/ath/ath5k/eeprom.c b/drivers/net/wireless/ath/ath5k/eeprom.c index 644962adda97..81ea52c4faff 100644 --- a/drivers/net/wireless/ath/ath5k/eeprom.c +++ b/drivers/net/wireless/ath/ath5k/eeprom.c @@ -1492,7 +1492,7 @@ ath5k_eeprom_read_target_rate_pwr_info(struct ath5k_hw *ah, unsigned int mode) * This info is used to calibrate the baseband power table. Imagine * that for each channel there is a power curve that's hw specific * (depends on amplifier etc) and we try to "correct" this curve using - * offests we pass on to phy chip (baseband -> before amplifier) so that + * offsets we pass on to phy chip (baseband -> before amplifier) so that * it can use accurate power values when setting tx power (takes amplifier's * performance on each channel into account). * diff --git a/drivers/net/wireless/ath/ath5k/phy.c b/drivers/net/wireless/ath/ath5k/phy.c index bbfdcd5e7cb1..72474c0ccaff 100644 --- a/drivers/net/wireless/ath/ath5k/phy.c +++ b/drivers/net/wireless/ath/ath5k/phy.c @@ -117,7 +117,7 @@ static unsigned int ath5k_hw_rfb_op(struct ath5k_hw *ah, /* * This code is used to optimize rf gain on different environments - * (temprature mostly) based on feedback from a power detector. + * (temperature mostly) based on feedback from a power detector. * * It's only used on RF5111 and RF5112, later RF chips seem to have * auto adjustment on hw -notice they have a much smaller BANK 7 and @@ -2746,7 +2746,7 @@ ath5k_setup_channel_powertable(struct ath5k_hw *ah, /* Fill curves in reverse order * from lower power (max gain) * to higher power. Use curve -> idx - * backmaping we did on eeprom init */ + * backmapping we did on eeprom init */ u8 idx = pdg_curve_to_idx[pdg]; /* Grab the needed curves by index */ @@ -2848,7 +2848,7 @@ ath5k_setup_channel_powertable(struct ath5k_hw *ah, /* Now we have a set of curves for this * channel on tmpL (x range is table_max - table_min * and y values are tmpL[pdg][]) sorted in the same - * order as EEPROM (because we've used the backmaping). + * order as EEPROM (because we've used the backmapping). * So for RF5112 it's from higher power to lower power * and for RF2413 it's from lower power to higher power. * For RF5111 we only have one curve. */ |